Abstract
This paper presents experimentally-obtained data which can be of importance in the design procedure of engineering components made of 1.4057 (X17CrNi16-2; AISI 431) steel. In this manner, uniaxialy tests related to determine material mechanical properties and short-time creep behavior were performed. Based on the mentioned tests, ultimate tensile strength, 0.2 offset yield strength and modulus of elasticity at low and elevated temperatures were determined. Also, creep behavior of considered steel was tested for selected temperatures and selected stress levels. According to experimentally determined Charpy impact energy an assessment of fracture toughness was made.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Bramfitt B L. Effects of Composition, Processing, and Structures on Properties of Irons and Steels, In: S. R. Lampman(Ed.), Materials Selection and Design[M]. OH: ASM International, 1997
Boresi A P, Schmidt R J. Advanced Mechanics of Materials[M]. sixth ed. New York: John Wiley & Sons, 2003
Collins A. Failure of Materials in Mechanical Design[M]. Second ed. New York: John Wiley & Sons, 1993
Solecki R, Conant P R. Advanced Mechanics of Materials[M]. New York: Oxford University Press, 2003
Findley W N, Lai J, Onaran S K. Creep and Relaxation of Nonlinear Viscoelastic Materials[M]. New York: Dover Publication, 1989
Raghavan V. Materials Science and Engineering[M]. New Delhi: Prentice-Hall of India, 2004
Timmins P F. Failure Control in Process Operations, In: S R Lampman Ed. Fatigue and Fracture[M]. OH: ASM International, 1997
Rajasekhar A, Madhusudhan G R, Mohandas T, et al. Influence of Austenitizing Temperature on Microstructure and Mechanical Properties of AISI 431 Martensitic Stainless Steel Electron Beam Welds [J]. Materials & Design, 2009, 30(5): 1 612–1 624
Manova D, Mändl S, Neumann H, et al. Influence of Annealing Conditions on Ion Nitriding of Martensitic Stainless Steel [J]. Surface and Coatings Technology, 2006, 200(22–23): 6 563–6 567
Manova D, Mändl S, Neumann H, et al. Wear Behaviour of Martensitic Stainless Steel after PIII Surface Treatment[J]. Surface and Coatings Technology, 2005, 200(1–4): 137–140
Yuan X, Sun D, Yu H, et al. Preparation of Amorphous-nanocrystalline Composite Structured Ni-P Electrodeposits[J]. Surface and Coatings Technology, 2007, 202(2): 294–300
Santa J F, Baena J C, Toro A. Slurry Erosion of Thermal Spray Coatings and Stainless Steels for Hydraulic Machinery[J]. Wear, 2007: 263(1–6): 258–264
Brnic J, Turkalj G, Canadija M, et al. Creep Behavior of High-strength Low-alloy Steel at Elevated Temperatures[J]. Mat. Sci. Eng. A, 2009, 499(1–2): 23–27
Brnic J, Turkalj G, Canadija M, et al. 50CrMo4 Steel-Determination of Mechanical Properties at Lowered and Elevated Temperatures, Creep Behavior and Fracture Toughness Calculation[J]. J. of Engineering Materials and Technology.-Trans. ASME, 2010, 132(2): 021 004
Pepelnjak T, Barisic B. Computer-assisted Engineering Determination of the Formability Limit for Thin Sheet Metals by a Modified Marciniak Method[J]. Journal of Strain Analysis for Engineering Design, 2009, 44(6): 459–472
Brnic J, Turkalj G, Canadija M. Optimal Design Procedure Based on Viscoplastic Material Behaviour[J]. Acta Metallurgica Sinica, 2000, 13(2): 587–592
Brnic J, Niu J, G Turkalj G, et al. Behavior of HSLA A709 Steel at Different Environmental Conditions[J]. Journal of Wuhan University of Technology-Mater. Sci. Ed., 2010, 25(6): 897–902
International Standard. Metalic Materials-Tensile Testing at Low Temperature[S]. ISO 15579:2000 (E), 2000
ASTM International. Annual Book of ASTM Standards, Metal Test Methods and Analytical Procedures[M]. Baltimore: ASTM International, 2012
Zhang L. Failure Assessment of Thin-walled Structures with Particular Reference to Pipelines[M]. Southampton: WIT Press, 2010
Anderson T L. Fracture Mechanics[M]. New York: CRC Press, 1995
Courtney T H. Fundamental Structure-property Relationships in Engineering Materials, In S. R. Lampman Ed. Materials Selection and Design[M].OH: ASM International, 1997
Shekhter A, Kim S, Carr D G, et al. Assesment of Temper Embrittlement in an Ex-service 1Cr-1Mo-0.25V Power Generating Rotor by Charpy V-Notch Testing, K Ic Fracture Toughness and Small Punch Test[J]. Int. Journal of Pressure Vessels and Piping, 2002, 79(8–10): 611–615
Roberts R, Newton C. Interpretive Report on Small Scale Test Correlations with K Ic Data[C]. Welding Research Council Bulletins, 1981
Y Chao, J D Ward, R G Sands. Charpy Impact Energy, Fracture Toughness and Ductile-brittle Transition Temperature of Dual-phase 590 Steel[J]. Materials & Design, 2007, 28(2): 551–557
Farahmand B, Bockrath G, Glassco J. Fatigue and Fracture Mechanics of High Risk Parts[M]. New York: International Thomson Publishing, 1997
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Brnic, J., Turkalj, G., Niu, J. et al. Significance of experimental data in the design of structures made from 1.4057 steel. J. Wuhan Univ. Technol.-Mat. Sci. Edit. 29, 131–136 (2014). https://doi.org/10.1007/s11595-014-0880-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11595-014-0880-0