Abstract
Time of flight diffraction (TOFD) is a well-developed ultrasonic non-destructive testing (NDT) technique which has been applied successfully for accurate sizing of defects in thick sections. Codes of practice such as ASME now permit TOFD for routine examination as an alternative to radiography for thick weldments. However, examination of thinner sections by TOFD has its limitations. The main limitation is that as the thickness of the specimen reduces, the lateral wave, diffracted wave and the back wall echo merge together and it is very difficult to identify and size the discontinuity. Also, the size of conventional transducers limits the required probe separation. Limited success has been obtained internationally through the application of miniature probes and software for extending TOFD to lower thicknesses. In these cases, the minimum thickness that has been examined is 7 mm. A new methodology based on a simple and novel combination of TOFD and the immersion technique has been proposed by the authors that successfully extends the application of TOFD to thinner sections down to 3 mm. Immersion coupling provides a delay line, the necessary angles and probe separation making it possible to examine the thin components successfully. This paper highlights the results of detailed experimental investigations on immersion TOFD and its successful application for the evaluation of welds in hexcan used for encapsulating nuclear fuel pins.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Silk, M.G.: The use of diffraction-based time of flight measurements to locate and size defects. Br. J. NDT 26, 208–213 (1984)
Ogilvy, J.A., Temple, J.A.G.: Diffraction of elastic waves by cracks: application to time of flight inspection. Ultrasonics 259–268 (1983)
Temple, J.A.G.: Time-of-flight inspection: theory. Nucl. Energy 22(5), 335–348 (1983)
Silk, M.G.: The transfer of ultrasonic energy in the diffraction technique for crack sizing. Ultrasonics 113–121 (1979)
Ravenscraft, F.A., Newton, K., Scruby, C.B.: Diffraction of ultrasound by cracks: comparison of experiment with theory. Ultrasonics 28, 29–37 (1991)
Verkooijen, J.: TOFD used to replace radiography. Insight 37(6), 433–435 (1995)
Subbaratnam, R., Abraham, S.T., Menaka, M., Venkatraman, B., Raj, B.: Application of time of flight diffraction technique for evaluation of austenitic stainless steel weldments at elevated temperatures. Mater. Eval. 66(3), 332–337 (2008)
Charlesworth, J.P., Temple, J.A.G.: Eng. Application of Ultrasonic Time of Flight Diffraction, 2nd edn. Springer, Berlin (2001)
Baskaran, G., Balasubramaniam, K., Krishnamurthy, C.V., Rao, L.: Ultrasonic TOFD flaw sizing and imaging in thin plates using embedded signal identification technique (ESIT). Insight 46(9), 537–542 (2004)
Baskaran, G., Balasubramaniam, K., Rao, C.L.: Shear-wave time of flight diffraction (S-TOFD) technique. NDT E Int. 39(6), 458–467 (2006)
Silk, M.G.: An evaluation of the performance of the TOFD techniques as a means of sizing flaws with particular reference to flaws with curved profiles. Insight 38(4), 280–287 (1996)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Subbaratnam, R., Abraham, S.T., Venkatraman, B. et al. Immersion and TOFD (I-TOFD): A Novel Combination for Examination of Lower Thicknesses. J Nondestruct Eval 30, 137–142 (2011). https://doi.org/10.1007/s10921-011-0101-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10921-011-0101-0