Skip to main content
SpringerLink
Log in

Elastic Modulus of 304 Stainless Steel Coating by Cold Gas Dynamic Spraying

  • Published:
Journal of Iron and Steel Research International Aims and scope Submit manuscript

Abstract

304 stainless steel coating was deposited on the IF steel substrate by cold gas dynamic spraying (CGDS), and the elastic modulus of the 304 stainless steel coating was studied. The elastic modulus of cold sprayed 304 stainless steel coating was measured using the three-point bend testing and the compound beam theory, and the other mechanic parameters (such as the equivalent flexural rigidity and the moment of inertia of area) of the coatings were also calculated using this compound beam theory. It is found that the calculated results using the above methods are accurate and reliable. The elastic modulus value of the cold sprayed 304 stainless steel coating is 1. 179×105 MPa, and it is slightly lower than the 304 stainless steel plate (about 2 × 105 MPa). It indicates that the elastic modulus of the cold sprayed coatings was quite different from the comparable bulk materials. The main reason is that the pores and other defects are existed in the coatings, and the elastic modulus of the coatings also depends on varies parameters such as the feed stock particle size, porosity, and processing parameters.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Pardhasaradhi S P, Venkatachalapathy V, Joshi S V, et al. Optical Diagnostics Study of Gas Particle Transport Phenomena in Cold Gas Dynamic Spraying and Comparison with Model Predictions [J]. Journal of the Thermal Spray Technology. 2008, 17(4): 551.

    Article  Google Scholar 

  2. Spencer K, Zhang M X. The Use of Kinetic Metallization to Form Intermetallic Reinforced Composite Coatings by Post-Spray Heat Treatment [J]. Surface and Coatings Technology, 2009, 203(20/21): 3019.

    Article  Google Scholar 

  3. Novoselova T, Fox P, Morgan R, et al. Experimental Study of Titanium/Aluminium Deposits Produced by Cold Gas Dynamic Spray [J]. Surface and Coatings technology, 2006, 200(8): 2775.

    Article  Google Scholar 

  4. Lee H, Lee S, Shin H, et al. Mechanical Matching and Micro-structural Evolution at the Coating/Substrate Interfaces of Cold-Sprayed Ni, Al Coatings [J]. Journal of Alloys and Compounds, 2009, 478(1/2): 636.

    Article  Google Scholar 

  5. Wang H T, Li C J, Yang G J, et al. Cold Spraying of Fe/AI Powder Mixture: Coating Characteristics and Influence of Heat Treatment on the Phase Structure [J]. Applied Surface Science, 2008, 255(5): 2538.

    Article  Google Scholar 

  6. Lee H Y, Jung S H, Lee S Y, et al. Correlation Between Al2O3 Particles and interface of Al-Al2O3 Coatings by Cold Spray [J]. Applied Surface Science, 2005, 252(5): 1891.

    Article  Google Scholar 

  7. Wu J W, Yang J G, Fang H Y, et al. The Bond Strength of Al-Si Coating on Mild Steel by Kinetic Spraying Deposition [J]. Applied Surface Science, 2006, 252(22): 7809.

    Article  Google Scholar 

  8. Guo X P, Zhang G, Li W Y, et al. Investigation of the Micro-structure and Tribological Behavior of Cold-Sprayed Tin-Bronze-Based Composite Coatings [J]. Applied Surface Science, 2009, 255(6): 3822.

    Article  Google Scholar 

  9. Zhao Z B, Gillispie B A, Smith J R. Coating Deposition by the Kinetic Spray Process [J]. Surface and Coatings Technology, 2006, 200(16/17): 4746.

    Article  Google Scholar 

  10. Li C J, Li W Y, Wang Y Y. Formation of Metastable Phases in Cold-Sprayed Soft Metallic Deposit [J]. Surface and Coatings Technology, 2005, 198(1/2/3): 469.

    Article  Google Scholar 

  11. Li C J, Li W Y. Deposition Characteristics of Titanium Coating in Cold Spraying [J]. Surface and Coatings Technology, 2003, 167(2/3): 278.

    Article  Google Scholar 

  12. Ajdelsztajn L, Zuniga A, Jodoin B, et al. Cold Gas Dynamic Spraying of a High Temperature Al alloy [J]. Surface and Coatings Technology, 2006, 201(6): 2109.

    Article  Google Scholar 

  13. Lima R S, Karthikeyan J, Kay C M, et al. Microstructural Characteristics of Cold-Sprayed Nanostructured WC-Co [J]. Thin Solid Films, 2002, 416(1/2): 129.

    Article  Google Scholar 

  14. Kim H J, Lee C H, Hwang S Y. Fabrication of WC-Co Coatings by Cold Spray Deposition [J]. Surface and oatings Technology, 2005, 191(2/3): 335.

    Article  Google Scholar 

  15. Kim H J, Lee C H, Hwang S Y. Superhard Nano WC-12 %Co Coating by Cold Spray Deposition [J]. Materials Science and Engineering A, 2005, 391(1/2): 243.

    Google Scholar 

  16. Lee H Y, Jung S H, Lee S Y, et al. Alloying of Cold-Sprayed Al-Ni Composite Coatings by Post-Annealing [J]. Applied Surface Science, 2007, 253(7): 3496.

    Article  Google Scholar 

  17. Stoloff N S, Liu C T, Deevi S C. Emerging Applications of Intermetallics [J]. Intermetallics, 2000, 8(9/10/11): 1313.

    Article  Google Scholar 

  18. Hodge A M, Dunand D C. Synthesis of Nickel-Aluminide Foams by Pack-Aluminization of nickel Foams [J]. Intermetallics, 2001, 9(7): 581.

    Article  Google Scholar 

  19. Mitchell T E, Hirth J P, Misra A. Apparent Activation Energy and Stress Exponent in Materials With a High Peierls Stress [J]. Acta Materialia, 2002, 50(5): 1087.

    Article  Google Scholar 

  20. Kim H J, Kweon Y G. Elastic Modulus of Plasma-Sprayed Coatings Determined by Indentation and Bend Tests [J]. Thin Solid Films, 1999, 342(1/2): 201.

    Article  Google Scholar 

  21. Li J F, Ding C X. Determining Microhardness and Elastic Modulus of Plasma-Sprayed Cr3C2-NiCr Coatings Using Knoop Indentation Testing [J]. Surface and Coatings Technology, 2001, 135(2/3): 229.

    Article  Google Scholar 

  22. CHENG Ying-ke, ZHANG Jian-jun, XU Lian-yong. Investigation on Measuring the Elastic Modulus of Coatings [J]. Sci-encepaper Online, 2008, 3(4): 293 (in Chinese).

    MathSciNet  Google Scholar 

  23. Bansal P, Shipway P H, Leen S B, et al. Experimental Validation of FE Predicted Fracture Behaviour of Thermally Sprayed Coatings [J]. Materials Science and Engineering A, 2006, 430(1/2): 104.

    Article  Google Scholar 

  24. Zhang K, Zhang K, Li H X, et al. Interface Fracture Behavior of Electroplated Coating on Metal Substrate Under Compressive Strain [J]. Journal of Materials Processing Technology, 2009, 209(3): 1337.

    Article  Google Scholar 

  25. XU Lian-yong, JING Hong-yang, HUO Li-xing, et al. Measuring of Young’s Modulus of Coatings by High Velocity Arc Spraying [J]. Transactions of the China Welding Institution, 2005, 26(4): 13 (in Chinese).

    Google Scholar 

  26. Sekiya S, Kakumakoto N, Tanimura S, et al. The Latest Mechanics of Materials [M]. Tokyo: [s. n.], 1990 (in Japanese).

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Material Science and Engineering, Dalian University of Technology, Dalian, Liaoning, 116085, China

    Wei Han (Master), Xian-ming Meng & Jie Zhao

  2. Baoshan Iron and Steel Company Limited, Baosteel Research Institute, Shanghai, 201900, China

    Jun-bao Zhang

Authors
  1. Wei Han
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Xian-ming Meng
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Jun-bao Zhang
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Jie Zhao
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Wei Han.

Additional information

Foundation Item: Item Sponsored by National Natural Foundtion of China (51134013, 51171037)

Rights and permissions

Reprints and permissions

About this article

Cite this article

Han, W., Meng, Xm., Zhang, Jb. et al. Elastic Modulus of 304 Stainless Steel Coating by Cold Gas Dynamic Spraying. J. Iron Steel Res. Int. 19, 73–78 (2012). https://doi.org/10.1016/S1006-706X(12)60077-6

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1016/S1006-706X(12)60077-6

Key words

Search

Navigation