Skip to main content

Advertisement

Log in

The contents and release behavior of heavy metals in construction and demolition waste used in freeway construction

  • Research Article
  • Published:
Environmental Science and Pollution Research Aims and scope Submit manuscript

Abstract

A large volume (more than 4.0 million m3) of treated construction and demolition waste (CDW) is planned to be used in the construction of the Xi’an-Xianyang north loop line freeway in West China. These CDW were preliminarily separated into broken concretes, bricks, and porcelains in the treatment plants. In this study, a total of 190 CDW samples including 80 concretes, 80 bricks, 20 porcelains, and 10 mixed samples were collected from five treatment plants. Five farmland soil samples near treatment plants were collected as controls. The contents of 10 elements including cadmium (Cd), arsenic (As), copper (Cu), nickel (Ni), zinc (Zn), chromium (Cr), lead (Pb), manganese (Mn), silver (Ag), and mercury (Hg) in these samples were measured. The contents of 8 elements (Cu, Ni, Zn, Cr, Pb, Mn, Ag, and Hg) in all CDW samples were qualified for the third-level criterion of the Standard of Soil Environment (GB15618-2008). However, Cd contents in 37 concretes, 34 bricks, 6 porcelain samples, and 4 mixed CDW samples exceeded the national third-level standards (1 mg/kg) in GB15618-2008. And As contents in 28 concretes, 21 bricks, 5 porcelain samples, and 3 mixed CDW samples were higher than the national third-level standards (40 mg/kg). The total exceeding standard rates (ESRs) of Cd and As were 42.6% and 30%, respectively. The leaching tests for Cd and As were also done due to their higher ESRs. The results showed that the release amounts (μg/kg) of Cd and As from CDW were increased with increasing liquid to solid ratio (0.4–10 l/kg) but decreased with increasing pH (4–7). The leached concentrations of Cd and As from four types of CDW samples were both in a descending order: brick, mixed materials, concrete, and porcelain. The measured concentrations (μg/L) of Cd and As in leachate were all lower than second-grade criteria of Standard for Groundwater Quality (GB3838-2002). By comparing the leached concentrations of Cd and As with the value in European criteria (EU Council Decision 2003/33/EC) for hazardous wastes, all the CDW samples should be classified as inert or non-hazardous wastes. Thus, it could be concluded that heavy metals in these CDW would not pollute surrounding soil, surface water, and groundwater environment when applied in freeway construction.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4

Similar content being viewed by others

References

  • Allegrini E, Butera S, Kosson DS, Zomeren AV, Van der Sloot HA, Astrup TF (2015) Life cycle assessment and residue leaching: the importance of parameter, scenario and leaching data selection. Waste Manag 38:474–485

    CAS  Google Scholar 

  • Alonso-Santurde R, Coz A, Quijorna N, Quijorna N, Viguri JR, Andrés A (2010) Valorization of foundry sand in clay bricks at industrial scale. J Ind Ecol 14:217–230

    CAS  Google Scholar 

  • Ashraf S, Ali Q, Zahir ZA, Ashraf S, Asghar HN (2019) Phytoremediation: environmentally sustainable way for reclamation of heavy metal polluted soils. Ecotox Environ Safe 174:714–727

    CAS  Google Scholar 

  • Barbudo A, Agrela F, Ayuso J, Jiménez JR, Poon CS (2012) Statistical analysis of recycled aggregates derived from different sources for sub-base applications. Constr Build Mater 28:129–138

    Google Scholar 

  • Butera S, Christensen TH, Astrup TF (2014) Composition and leaching of construction and demolition waste: inorganic elements and organic compounds. J Hazard Mater 276:302–311

    CAS  Google Scholar 

  • Butera S, Hyks J, Christensen TH, Astrup TF (2015) Construction and demolition waste: comparison of standard up-flow column and down-flow lysimeter leaching tests. Waste Manag 43:386–397

    CAS  Google Scholar 

  • Cardoso R, Silva RV, De Brito J, Dhir R (2016) Use of recycled aggregates from construction and demolition waste in geotechnical applications: a literature review. Waste Manag 49:131–145

    Google Scholar 

  • Chandler AJ, Eighmy TT, Hartlén J, Hjelmar O, Sawell DKS, van der Sloot H, Hardbound JV (1997) Municipal solid waste incinerator residues. Elsevier, Amsterdam

    Google Scholar 

  • Cocke DL, Mollah MYA (1993) The chemistry and leaching mechanisms of hazardous substances in cementitious solidification/stabilization systems. In: Spence RD (ed) Chemistry of microestructure solidified waste forms. Lewis Publishers, Boca Raton, pp 187–242

    Google Scholar 

  • CSATICWRI, 2014. Industrialization development report of China’s construction waste resource, 2014 Annual Report. China Strategic Alliance of Technological Innovation for Construction Waste Recycling Industry (CSATICWRI) In Chinese

  • Delay M, Lager T, Schulz HD, Frimmel FZ (2007) Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste. Waste Manag 27:248–255

    CAS  Google Scholar 

  • Ding T, Xiao J (2014) Estimation of building-related construction and demolition waste in Shanghai. Waste Manag 34:2327–2324

    Google Scholar 

  • Domingo N, Luo H (2017) Canterbury earthquake construction and demolition waste management: issues and improvement suggestions. Int J Disaster Risk Reduct 22:130–138

    Google Scholar 

  • Duan H, Wang J, Huang Q (2015) Encouraging the environmentally sound management of C&D waste in China: an integrative review and research agenda. Renew Sust Energ Rev 43:611–620

    Google Scholar 

  • Engelsen CJ, Van der Sloot HA, Wibetoe G, Petkovic G, Stoltenberg-Hansson E, Lund W (2009) Release of major elements from recycled concrete aggregates and geochemical modeling. Cement Concrete Res 39:446–459

    CAS  Google Scholar 

  • Engelsen CJ, Van der Sloot HA, Wibetoe G, Justnes H, Lund W, Stoltenberg-Hansson E (2010) Leaching characterization and geochemical modeling of minor and trace elements released from recycled concrete aggregates. Cement Concrete Res 40:1639–1649

    CAS  Google Scholar 

  • EU Council Decision 2003/33/EC of 19 December 2002. Establishing criteria and procedures for the acceptance of waste at landfills pursuant to Article 16 and Annex II to Directive 1999/31/EC

  • Ezemonye LI, Adebayo PO, Enuneku AA, Tongo I, Ogbomida E (2019) Potential health risk consequences of heavy metal concentrations in surface water, shrimp (Macrobrachium macrobrachion) and fish (Brycinus longipinnis) from Benin River, Nigeria. Toxicol Rep 6:1–9

    CAS  Google Scholar 

  • Galvín AP, Ayuso J, Agrela F, Ayuso J, Jiménez JR (2012) Comparison of batch leaching tests and influence of pH on the release of metals from construction and demolition wastes. Waste Manag 32:88–95

    Google Scholar 

  • Galvín AP, Ayuso J, Agrela F, Barbudo A, Jiménez JR (2013) Analysis of leaching procedures for environmental risk assessment of recycled aggregate use in unpaved roads. Constr Build Mater 40:1207–1214

    Google Scholar 

  • Galvín AP, Ayuso J, García I, Jimenez JR, Gutierrez F (2014) The effect of compaction on the leaching and pollutant emission time of recycled aggregates from construction and demolition waste. J Clean Prod 83:294–304

    Google Scholar 

  • Garrabrants AC, Sanchez F, Kosson DS (2004) Changes in constituent equilibrium leaching and pore water characteristics of a Portland cement mortar as a result of carbonation. Waste Manag 24:19–36

    CAS  Google Scholar 

  • GB15618-2008 environmental quality standard for soil, China. http://datacenter.mee.gov.cn/websjzx/report/list.vm (In Chinese)

  • GB3838-2002 environmental quality standard for surface water, China. http://datacenter.mee.gov.cn/websjzx/report!list.action?xmlname=1520238134405 (In Chinese)

  • Huang B, Wang X, Kua H, Geng Y, Bleischwitz R, Ren J (2018) Construction and demolition waste management in China through the 3R principle. Res Conserv Recy 129:36–44

    Google Scholar 

  • Huang J, Peng S, Mao X, Li F, Guo S, Shi L, Shi Y, Yu H, Zeng G (2019) Source apportionment and spatial and quantitative ecological risk assessment of heavy metals in soils from a typical Chinese agricultural county. Process Saf Environ 126:339–347

    Google Scholar 

  • Jia S, Yan G, Shen A, Zheng J (2017) Dynamic simulation analysis of a construction and demolition waste management model under penalty and subsidy mechanisms. J Clean Prod 147:531–545

    Google Scholar 

  • Jin R, Li B, Zhou T, Wanatowski D, Piroozfar P (2017) An empirical study of perceptions towards construction and demolition waste recycling and reuse in China. Resour Conserv Recy 126:86–98

    Google Scholar 

  • Juan-Valdés A, Rodríguez-Robles D, García-González J, Guerra-Romero MI, Pozo JMM (2018) Mechanical and microstructural characterization of non-structural precast concrete made with recycled mixed ceramic aggregates from construction and demolition wastes. J Clean Prod 180:482–493

    Google Scholar 

  • Kianimehr M, Shourijeh PT, Binesh SM, Mohammadinia A, Arulrajah A (2019) Utilization of recycled concrete aggregates for light-stabilization of clay soils. Constr Build Mater 227:116792–116802

    Google Scholar 

  • Li XD, Poon CS, Sun H, Lo IMC, Kirk DW (2001) Heavy metals speciation and leaching behaviors in cement based solidified/stabilized wasted materials. J Hazard Mater 82:215–230

    Google Scholar 

  • Liang J, Feng C, Zeng G, Gao X, Zhong M, Li X, Li X, He X, Fang Y (2017) Spatial distribution and source identification of heavy metals in surface soils in a typical coal mine city, Lianyuan, China. Environ Pollut 225:681–690

    CAS  Google Scholar 

  • Liang J, Liu J, Xu G, Chen B (2019) Distribution and transport of heavy metals in surface sediments of the Zhejiang nearshore area, East China Sea: sedimentary environmental effects. Mar Pollut Bull 146:542–551

    CAS  Google Scholar 

  • Lidelöw S, Macsik J, Carabante I, Kumpiene J (2017) Leaching behaviour of copper slag, construction and demolition waste and crushed rock used in a full-scale road construction. J Environ Manag 204:695–703

    Google Scholar 

  • Liu M, Zhang A, Liao Y, Chen B, Fan D (2015) The environment quality of heavy metals in sediments from the central Bohai Sea. Mar Pollut Bull 100:534–543

    CAS  Google Scholar 

  • Milenkovic B, Stajic JM, Stojic N, Pucarevic M, Strbac S (2019) Evaluation of heavy metals and radionuclides in fish and seafood products. Chemosphere 229:324–331

    CAS  Google Scholar 

  • Mulugeta M, Engelsen CJ, Wibetoe G, Lund W (2011) Charge-based fractionation of oxyanion-forming metals and metalloids leached from recycled concrete aggregates of different degrees of carbonation: a comparison of laboratory and field leaching tests. Waste Manag 31:253–258

    CAS  Google Scholar 

  • Mwesigye AR, Young SD, Bailey EH, Tumwebaze SB (2016) Population exposure to trace elements in the Kilembe copper mine area, Western Uganda: a pilot study. Sci Total Environ 573:366–375

    CAS  Google Scholar 

  • Nakamura K, Kinoshita S, Takatsuki H (1996) The origin and behavior of lead, cadmium, and antimony in MSW incinerator. Waste Manag 16:509–517

    CAS  Google Scholar 

  • NEN 7341, 1994. Determination of the leaching characteristics of soil, construction materials and wastes–leaching tests–determination of the availability of inorganic constituents for leaching from construction materials and waste materials. Nederlands Normalisatie-Instituut

  • Poon CS, Chan D (2006) Feasible use of recycled concrete aggregates and crushed clay brick as unbound road sub-base. Constr Build Mater 20:578–585

    Google Scholar 

  • Rahman MA, Arulrajah A, Piratheepan J, Bo MW, Imteaz MA (2013) Resilient modulus and permanent deformation responses of geogrid-reinforced construction and demolition materials. J Mater Civ Eng 26:512–519

    Google Scholar 

  • Ravindra K, Mor S (2019) Distribution and health risk assessment of arsenic and selected heavy metals in groundwater of Chandigarh, India. Environ Pollut 250:820–830

    CAS  Google Scholar 

  • Robey NM, Solo-Gabriele HM, Jones AS, Marini J, Townsend TG (2018) Metals content of recycled construction and demolition wood before and after implementation of best management practices. Environ Pollut 242:1198–1205

    CAS  Google Scholar 

  • Rotter VS, Kost T, Winkler J, Bilitewski B (2004) Material flow analysis of RDF-production process. Waste Manag 24:1005–1021

    CAS  Google Scholar 

  • Roussat N, Méhu J, Abdelghafour M, Brula P (2008) Leaching behavior of hazardous demolition waste. Waste Manag 28:2032–2040

    CAS  Google Scholar 

  • Silva RV, de Brito J, Dhir RK (2014) Properties and composition of recycled aggregates from construction and demolition waste suitable for concrete production. Constr Build Mater 65:201–217

    Google Scholar 

  • Sun C, Zhang Z, Cao H, Xu M, Xu L (2019) Concentrations, speciation, and ecological risk of heavy metals in the sediment of the Songhua River in an urban area with petrochemical industries. Chemosphere 219:538–545

    CAS  Google Scholar 

  • Tavira J, Jiménez JR, Ayuso J, Sierra MJ, Ledesma EF (2018) Functional and structural parameters of a paved road section constructed with mixed recycled aggregates from non-selected construction and demolition waste with excavation soil. Constr Build Mater 164:57–69

    Google Scholar 

  • Townsend TG, Jang YC, Tolaymat T (2003) Leaching tests for evaluating risk in solid waste management decision making, Florida Center for Solid and Hazardous. Waste management. Report no. 03-01. Gainesville, USA

  • Townsend T, Tolaymat T, Leo K, Jambeck J (2004) Heavy metals in recovered fines from construction and demolition debris recycling facilities in Florida. Sci Total Environ 332:1–11

    CAS  Google Scholar 

  • Van der Sloot HA, Van Zomeren A, Dijkstra JJ, Hoede D, Scharff H (2002) Modeling of the source term for a predominantly inorganic waste landfill using data obtained from laboratory scale testing, lysimeter studies and pilot scale monitoring. Second intercontinental landfill research symposium, Asheville

    Google Scholar 

  • Vegas I, Ibañez JA, José JTS, Urzelai A (2008) Construction demolition wastes, Waelz slag and MSWI bottom ash: a comparative technical analysis as material for road construction. Waste Manag 28:565–574

    CAS  Google Scholar 

  • Wahlstrom M, Laine-Ylijoki J, Maattanen A (2000) Environmental quality assurance system for use of crushed mineral demolition wastes in road constructions. Waste Manag 20:225–232

    CAS  Google Scholar 

  • Wen X, Lu J, Wu J, Lin Y, Luo Y (2019) Influence of coastal groundwater salinization on the distribution and risks of heavy metals. Sci Total Environ 652:267–277

    Google Scholar 

  • Xiao J, Xie H, Zhang C (2012) Investigation on building waste and reclaim in Wenchuan earthquake disaster area. Resour Conserv Recy 61:109–117

    Google Scholar 

  • Yin S, Feng C, Li Y, Yin L, Shen Z (2015) Heavy metal pollution in the surface water of the Yangtze Estuary: a 5-year follow-up study. Chemosphere 138:718–725

    CAS  Google Scholar 

  • Yu D, Duan H, Song Q, Li X, Zhang H, Zhang H, Liu Y, Shen W, Wang J (2018) Characterizing the environmental impact of metals in construction and demolition waste. Environ Sci Pollut Res 25:13823–13832

    CAS  Google Scholar 

  • Yuan H (2013) A SWOT analysis of successful construction waste management. J Clean Prod 39:1–8

    CAS  Google Scholar 

  • Zhang J, Gu F, Zhang Y (2019) Use of building-related construction and demolition wastes in highway embankment: laboratory and fifield evaluations. J Clean Prod 230:1051–1060

    Google Scholar 

  • Zhao Y, Huang S (2017) Chapter six: migration patterns of pollutants in construction & demolition waste. Pollution Control and Resource Recovery, pp 125–146

Download references

Funding

The research was supported by the National Natural Science Funds of China (Grant No. 41302206), the Provincial Natural Science Foundation of Shaanxi Province, China (Grant No. 2018JM4039), the Science and Technology Project of Ministry of Transport construction (Grant No. 2013318J16490), and the Fundamental Research Funds for the Central Universities, CHD (Grant No. 300102299205).

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Yuyun Chen.

Additional information

Responsible editor: Philippe Garrigues

Publisher’s note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Chen, Y., Zhou, Y. The contents and release behavior of heavy metals in construction and demolition waste used in freeway construction. Environ Sci Pollut Res 27, 1078–1086 (2020). https://doi.org/10.1007/s11356-019-07067-w

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11356-019-07067-w

Keywords

Navigation