Abstract
Discordant iron-rich ultramafic pegmatites (IRUPs) intersect the UG2 chromitite at many places in the Bushveld Complex. The effects of IRUP interactions on the UG2 ore mineralogy and PGE grade are assessed at the Thaba mine, north-west Bushveld, based on a borehole profile through the UG2 layer and detailed analysis of mineral textures and compositional variations across the UG2-IRUP contacts using micro-XRF element mapping. The UG2-IRUP interaction operated at different scales and probably by different mechanisms. At the local scale (< 10 cm), a thin layer of Fe–Ti–Cr spinel and ilmenite formed on the IRUP side of the contact with UG2, whereas the UG2 chromitite developed grain coarsening, loss of interstitial silicates, and chemical gradients in Cr, Al, Fe, and Ti that extend a few centimeters from the contact into the seam. These local effects are attributed to the intrusion of IRUP melt into the solidified UG2 layer, followed by re-equilibration of the oxide minerals across the contact during cooling. On a larger scale, changes in the ore and gangue mineral assemblages in UG2 took place throughout the entire meter-thick main seam. Compared with regional UG2 compositions, chromite has higher TiO2 and lower Mg#, and there is an anomalously low abundance of interstitial plagioclase. The IRUP-affected UG2 shows relatively abundant secondary hydrous silicates, replacement of PGE sulfides by PGE alloys and PGE-As–Sb–Bi–Te–Pb phases, and formation of secondary Ni–Cu–Fe sulfides after pentlandite and chalcopyrite. These large-scale effects are attributed to hydrothermal fluids derived from IRUP melts. The IRUP bodies at the Thaba mine caused redistribution of PGE within the UG2 layer but did not significantly reduce the overall grade. However, significant changes in the ore mineral assemblage and an increased abundance of secondary silicates can reduce the efficiency of PGE recovery.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Discordant bodies of iron-rich ultramafic pegmatite (IRUP) are widespread in the Rustenburg Layered Suite (RLS) of the Bushveld Complex. The name IRUP derives from the distinctly coarse grain size, the iron-rich nature of constituent mafic silicates, and the local abundance of Fe–Ti oxide minerals (Viljoen and Scoon 1985). Field observations and several geochemical–mineralogical studies have demonstrated that IRUP bodies formed from a mobile phase at high temperatures and that they partly replaced existing layered-suite rocks. There is still no consensus on the nature of IRUP-generating melts or fluids, nor on how and where they form (Viljoen and Scoon 1985; Scoon and Mitchell 1994, 2004, 2020; Cawthorn et al. 2000, 2018; Reid and Basson 2002; Scoon et al. 2017). In this paper, we use the term IRUP melt but acknowledge that its nature is undefined. IRUP bodies occur in most levels of the Rustenburg Layered Suite above the Lower Zone, but they are particularly well known in the Upper Critical Zone where they intersect the Merensky Reef and UG2 platinum group element (PGE) orebodies. Several studies of the contact zones of IRUP with Merensky Reef have shown that the interaction caused changes in the ore assemblages of the reef and some remobilization of metals (Viljoen and Scoon 1985; Kinloch 1982; Scoon and Mitchell 1994, 2011; Viring and Cowell 1999; Reid and Basson 2002; Scoon and Eales 2002). The effects of IRUP’s interaction with the UG2 chromitite have been less well studied. Penberthy and Merkle (1999) mentioned the effects of IRUP on the mineralization of the UG2 in a regional overview of the Bushveld Complex, but detailed case studies are lacking. A study by Mitchell et al. (2019a) described the contact zone of UG2 with IRUP from a platinum exploration project at Wilgerspruit in the western limb, but no information on PGE concentrations or mineralogy was reported.
This paper presents a case study of the mineralogical and geochemical effects of IRUP-UG2 interaction as revealed in a drillcore profile from the Thaba chromite mine in the northwestern Bushveld Complex. The borehole MD17 is located at the edge of one of the largest known IRUP bodies in the complex, the 1.5-km-diameter Middellaagte body. This was described as a pipe by Viljoen and Scoon (1985) and is incorrectly marked on Thaba mine records as “dunite pipe,” but it has since been characterized as disc-shaped (Scoon et al. 2017). The 645-m borehole contains many IRUP intersections, which we interpret as apophyses of the main body. These include one about 6-m thick at the footwall of the UG2 chromitite and two cm-thick IRUPs within the main seam, which are the subject of this study. We present electron microprobe analyses of the major oxide and silicate phases in the IRUPs, the UG2 layer, and the hanging wall pyroxenite, as well as quantitative ore mineralogy by mineral liberation analysis (MLA) and PGE distribution from a series of samples through the UG2 chromitite. Detailed textural and compositional profiles across the contacts of all three IRUP bodies with UG2 were obtained by micro-X-ray fluorescence (micro-XRF) element mapping. These data are used to document the variations in PGE geochemistry and mineralogy of the IRUP-effected UG2 chromitite and to understand how IRUPs interact with UG2.
Geological setting
The Bushveld Complex, summarized by Cawthorn (2015) and Viljoen (2016), comprises the approximately 8-km-thick Rustenburg Layered Series (RLS) of mafic to ultramafic rocks, the overlying 3.5-km-thick volcanic and subvolcanic roof rocks known as the Rooiberg Group, and granitic intrusions of the Lebowa Suite that were emplaced between the layered series and roof rocks. Radiometric dating suggests that all igneous components of the Bushveld Complex, including the felsic units at the roof were emplaced over a period of ~ 5 Ma from 2060 to 2055 Ma (Scoates et al. 2021). The focus of this paper is on the Critical Zone of the RLS, which hosts world-class PGE and Cr deposits. The Critical Zone contains about a dozen layers of chromitite, each on the order of tens of centimeters to 1-m thick, and many more centimeter-thick or thinner chromitite stringers. The chromitite layers are grouped into a lower (LG), middle (MG), and upper group (UG), each of which contains several layers numbered consecutively upwards from the base (inset in Fig. 1). The UG2 is stratigraphically the second-highest chromitite layer of the upper group. There has been abundant research on the geology and mineralogy of the UG2 and other chromitite layers since the 1970s (Von Gruenewaldt et al. 1986; Naldrett et al. 2012), but debate continues on how they formed (Kinnaird et al. 2002; Voordouw et al. 2009; Latypov et al. 2017, 2018; Cawthorn et al. 2018; Mitchell et al. 2019b; Veksler and Hou 2020; Zhou et al. 2021).
Discordant IRUP bodies in the RLS are widespread on the eastern and western limbs of the Bushveld Complex, occurring in the Critical, Main, and Upper Zones. The IRUP bodies vary considerably in composition and form, depending partly on the stratigraphic interval in which they occur (e.g., Scoon and Mitchell 1994). The rocks are dominantly made up of Fe-rich clinopyroxene and olivine, with variable amounts of Fe–Ti oxides and accessory sulfide minerals occurring locally. Typical features that set IRUPs apart from their host-rock pyroxenites and norites are as follows: (1) a coarser grain size, (2) higher Fe/(Fe + Mg) ratios of ferromagnesian minerals, (3) a paucity of plagioclase and orthopyroxene, and (4) a higher abundance of hydrous phases (accessory amphibole and mica). Field observations demonstrate a spatial association of IRUP with zones of structural disturbance in the RLS (i.e., faults, dome structures), highly variable shapes of the IRUP bodies, and a differential replacement of the layered series rocks by IRUP, which is especially strong for plagioclase-rich lithologies and weak for chromitite and ultramafic layers (Cameron and Desborough 1964; Viljoen and Scoon 1985; Reid and Basson 2002). Mineral compositions of pyroxene and plagioclase (Scoon and Mitchell 1994), as well as O-isotope exchange thermometry (Cawthorn et al. 2000), attest to high temperatures of formation and a magmatic affinity, but the rock composition represents mineral accumulation, not quenched magma. Initial Sr isotope ratios of IRUP in the Critical Zone contrast with those of the host rocks but resemble those of the Upper Zone (Scoon and Mitchell 1994; Reid and Basson 2002). This, and the similar Ti-magnetite compositions in IRUP and in magnetite layers of the Upper Zone suggest that IRUP may have derived from residual or exsolved melts from the Upper Zone, an idea supported by field evidence for downward-directed emplacement of IRUP (Scoon and Mitchell 2021). On the other hand, Cawthorn et al. (2018) argued for an external source of the IRUP melts, so many fundamental questions about the origin of IRUPs remain unanswered.
Geology of the Thaba mine and borehole MD17
The Thaba mine in the northwestern Bushveld Complex produces chromite from the chromitite layers LG-6, LG-6A, and MG-1 to MG-4. This rock package dips southeast at 15° to 27° and is cut by steep, NW–SE trending normal faults (Fig. 2). Mafic dikes with the same orientation as the faults also occur. Information about the mineralogy and ore grades of the LG and MG chromitite layers at Thaba, including their PGE concentrations, is given by Bachmann et al. (2018) and Kaufmann et al. (2019). The Thaba mining lease is adjacent and parallel to the Amandelbult section (Dishaba and Tumela platinum mines), which exploits the UG2 and the Merensky Reef. South-east of the Amandelbult section is the Northam platinum mine, which also exploits UG2 and Merensky Reef ores (Fig. 1). The UG2 chromitite is generally not exposed in the Thaba mine, with the exception of a graben that is also the locus of the Middellaagte IRUP body. Many smaller IRUPs in the vicinity of the Middellaagte body are known from outcrops and magnetic surveys (Viljoen and Scoon 1985). Borehole logs from the Thaba mine compiled by Bachmann et al. (2019) show that IRUP intersections are widespread in the stratigraphic interval of the LG and MG series chromitites (Fig. 2A).
Viljoen and Scoon (1985) and Scoon and Mitchell (1994) described the geology of the Middellaagte body and smaller IRUPs in the region in detail, including observations from underground exposures in the Amandelbult mine to the west of the main body. They also provided bulk-rock and mineral geochemical data from IRUP and host rocks and discussed the possible origin of IRUP, including comparisons with occurrences in the eastern limb of the Bushveld Complex. Three clusters of IRUPs were recognized by Viljoen and Scoon (1985), all of which are related to NW–SE trending faults. The Middellaagte body, with a 1.5-km-diameter subcircular outcrop pattern, is located in a graben (Fig. 2A) with about 500 m of vertical offset. Underground exposures in the Amandelbult mine demonstrate that IRUP extensively replaced pre-existing rocks of the layered suite, especially those rich in plagioclase (Fig. 2B). In places, IRUP has largely replaced the Merensky Reef feldspathic pyroxenite, leaving the chromitite stringers partly intact (Scoon and Mitchell 2011). An interesting feature of the replaced Merensky Reef described by Scoon and Eales (2002) is the transformation of chromite to an intermediate Fe–Ti–Cr spinel and the local thickening of relict chromitite stringers by the formation of a new, oxide-rich layer. Similar oxide-rich contact zones between IRUP and chromitite have been found elsewhere in the Bushveld Complex (e.g., Cameron and Glover 1973; Mitchell et al. 2019a), and this is also a prominent feature of the IRUP-UG2 contact at Thaba mine as described below.
Petrography of the UG2 and IRUP in MD17
The MD17 borehole was drilled to a depth of 645 m and intersects Critical Zone chromitite layers from UG2 at 143 m below the collar to LG1 at 633 m. Core logs show that the upper 130 m of MD17 consists almost entirely of IRUP, interrupted by a few intervals of pyroxenite and norite 2 to 5 m thick. Thinner sheets of IRUP occur at and below the UG2, which we interpret as apophyses of the Middellaagte body.
The drillcore profile investigated in this study comprises a 2.3-m interval across the UG2 chromitite, extending from the pyroxenite hanging wall through two chromitite leaders and the main seam (1.5-m thick), and ending in the IRUP footwall (Fig. 3). The core interval shows that the footwall IRUP is 6.5-m thick (referred to herein as IRUP-1). Two additional, thin IRUP apophyses (IRUP-2 and IRUP-3, about 4-cm thick each) occur within the main UG2 seam.
The footwall IRUP-1 is made up of approximately 40 vol.% clinopyroxene (up to 20 mm), 40% olivine (up to 10 mm), 10% Ti–Fe oxides, 6% hornblende, 2% sulfides, and 2% combined orthopyroxene, plagioclase, and phlogopite. Hornblende occurs as independent grains (up to 5 mm) and locally as inclusions (50–500 μm) in clinopyroxene. Euhedral phlogopite is present as inclusions in hornblende. Plagioclase (1–2 mm), sulfide, and oxide minerals are sparsely disseminated in the interstitial network. The oxide assemblage comprises titanomagnetite and ilmenite with Cr–Fe–Ti spinel forming at the UG2 contact. The sulfide minerals are dominated by pyrrhotite, with minor pentlandite, chalcopyrite, and cubanite. Similar sulfide mineral assemblages have been reported in the IRUP from the Middellaagte body and elsewhere in the Upper Critical Zone (Scoon and Mitchell 1994, 2011; Reid and Basson 2002).
The IRUP-2 and IRUP-3 bodies occur within the main chromitite seam at 37 and 84 cm above its base, respectively. They mainly consist of olivine and clinopyroxene, in modal proportions of 35% vs. 65%, respectively, in IRUP-2 and 75% vs. 25% in IRUP-3. Accessory sulfide and oxide minerals have similar proportions and characteristics as described for IRUP-1.
The UG2 chromitite main seam has two textural varieties, equigranular and poikilitic, which also differ in mineral proportions as determined by MLA (Zhou et al. 2023). The more common equigranular variety contains 81 to 86 vol.% chromite with interstitial silicate minerals comprising orthopyroxene (1–6%), olivine (1–10%), and hornblende (0.5–11%), with minor phlogopite, alteration phases (chlorite, serpentinite, talc,) and accessory amounts of apatite, feldspar, rutile, and quartz. The poikilitic chromitite, with up to centimeter-sized orthopyroxene oikocrysts, has less chromite (70–78%) and more orthopyroxene (10–20%) than the equigranular variety but similar amounts of olivine, hornblende, and minor silicates as the latter. Interstitial Fe–Ni–Cu sulfides and PGE minerals comprise less than 0.1%.
Two chromitite “leaders” (20 and 15 cm in thickness) occur in the hanging wall pyroxenite. Both are characterized by a poikilitic texture with orthopyroxene oikocrysts. Mitchell et al. (2019a) also noted a poikilitic texture in the UG2 leaders at Winnarshoek. Only the upper leader in MD17 was analyzed for quantitative mineralogy, and the results are similar to those of poikilitic samples from the main seam.
Finally, the pyroxenite hanging wall is made up mainly of orthopyroxene, with interstitial plagioclase and minor hornblende, disseminated chromite, and olivine.
Sampling and analytical methods
The drillcore through UG2 was cut into 60 segments of 3–5-cm length, numbered upwards from MD17-01 to MD17-60. Thin sections for the petrographic study were prepared from all segments, and a subset of these (Fig. 3) was chosen for analysis.
Whole-rock PGE analyses were performed by fire assay with nickel sulfide collection at Mintek Analytical Services Division in Johannesburg, South Africa. After crushing and milling, the samples were fused with nickel sulfide, the sulfide bead was dissolved in aqua regia, and the solution was analyzed for five PGEs (Pt, Pd, Ir, Rh, Ru) and Au using inductively coupled plasma-optical emission spectrometry (ICP-OES). A minimum of 40 g of sample mass was needed for each analysis, and this required combining two of the 3–5-cm drillcore segments as one assay sample. Due to the small thickness of IRUP layers 2 and 3, only the footwall IRUP-1 could be analyzed for PGE. Four samples from the UG2 chromitite were analyzed (UG2-1 to UG2-4), one from the upper chromitite leader (UG2-5), and one from the pyroxenite hanging wall (Fig. 3). Reference Material SARM-64 was analyzed with the samples to monitor analytical accuracy, and the results are included with the UG2 analyses in Table 1.
MLA was used to determine the identity and distribution of ore and gangue minerals in polished thin sections. The MLA instrumentation at the Helmholtz Institute Freiberg for Resource Technology (Bachmann et al. 2017) combines an FEI Quanta 650F scanning electron microscope (SEM) with two Bruker Quantax X-Flash 5030 energy-dispersive X-ray spectrometers (EDS). Automated data acquisition and analysis were controlled by the MLA 3.1.4 software suite using the sparse phase liberation (SPL-Lt) mode (Fandrich et al. 2007). The MLA study was done on 14 polished thin sections, 10 of which correspond to the sections used for whole-rock PGE analyses of the main seam and upper leader. An additional four samples were chosen to include the base of UG2 above the footwall IRUP-1 (MD17-04, MD17-07) and the middle of UG2 below IRUP-3 (MD17-23, MD17-24). The position of the thin sections studied and their correspondence with the fire-assay samples are shown in Fig. 3.
Following Voordouw et al. (2010) and Bachmann et al. (2018), the assemblages of PGE minerals, base-metal sulfides (BMS), and silicate minerals are simplified into six groups each. For the PGE minerals, these are as follows: (1) PtPdS group (cooperite-braggite-vysotskite), (2) laurite group (laurite-ehrlichmannite: (Ru,Ir,Os)S2), (3) PGE-CuS group (malanite-cuprorhodsite: Cu(Pt,Rh)2S4), (4) PGE-FeSn alloy group (ferroplatinum, rustenburgite), (5) PGE-AsS group (hollingworthite, irarsite, ruarsite, platarsite: (Pt,Rh,Ir)AsS), (6) PGE-SbBiTePb group (geversite, insizwaite, moncheite, stibiopalladinite, sudburyite). The six BMS mineral groups are as follows: (1) pentlandite, (2) chalcopyrite, (3) Py/Po (pyrite, pyrrhotite), (4) CuFeS group (chalcocite, bornite, cubanite, covellite, enargite), (5) millerite (NiS), and (6) violarite (FeNi3S4). The gangue minerals are grouped into (1) pyroxene, (2) olivine, (3) feldspars, (4) amphibole, (5) alteration silicates (chlorite, serpentine, talc), and (6) carbonate. Quartz, biotite, and other accessory minerals (e.g., apatite, zircon, monazite, rutile, and barite) were also detected, but their abundance is negligible in the samples.
Electron probe microanalysis (EPMA) on polished, carbon-coated thin sections was carried out using a JEOL super probe JXA-8230 instrument at the German Research Centre for Geosciences (GFZ), Potsdam. An accelerated voltage of 15 kV, a beam current of 20 nA, and beam sizes of 3 μm (for Fe–Ti–Cr oxides), 5 μm (for olivine, pyroxenes, hornblende, and phlogopite), and 15 μm (for plagioclase) were used for measurement. Analytical details about the standards, X-ray lines used, counting time on peak and background, and detection limits are listed in Zhou et al. (2023).
Micro-XRF mapping of element distribution across the contact zones between IRUP and chromitite was obtained by a Bruker Tornado M4 micro-XRF instrument at GFZ Potsdam. The instrument is equipped with an Rh X-ray source that operates at 50 kV and 600 µA and with poly-capillary X-ray optics that irradiates a spot of 20 µm for 50 ms. Dual 30 mm2 Si-drift detectors were used for spectra acquisition. Element intensities were normalized by an initial spectrum deconvolution and visualized by relative element abundance in 2D maps with a spatial resolution of 50 µm.
Platinum-group element concentrations and ore mineralogy
Whole-rock analyses
The PGE concentrations of IRUP, UG2 chromitite, and hanging wall pyroxenite are listed in Table 1. A summary of total 5PGE + Au concentrations (Pt, Pd, Ir, Rh, Ru, Au), and the distribution of individual elements and element ratios in the profile are shown in Fig. 4A. The values are compared with the average UG2 from Amandelbult (McLaren and De Villiers 1982; Von Gruenewaldt et al. 1986) and with a regional UG2 average (Barnes and Maier 2002) on a chondrite-normalized plot in Fig. 4B. Values of the 5PGE + Au in the UG2 main seam are between 2.8 and 11.4 ppm, with an average of 5.8 ± 3.4 ppm (n = 5). The highest value occurs near the top (sample UG2-4, with 11.4 ppm), which is twice that of the next-highest value of 5.9 ppm in sample UG2-1 from the base. The upper leader (sample UG2-5) yielded a value of 5.3 ppm. The values in the footwall IRUP-1 and the hanging wall pyroxenite are 0.16 and 0.26 ppm, respectively.
Platinum-group element ratios also vary with sample height in the UG2 profile (Fig. 4A). The Pt/Pd ratios are between 1.8 and 2.5 in all but one UG2 sample from MD17. These values agree with the average Pt/Pd ratio of 2.5 for UG2 in the western Bushveld according to McLaren and Villiers (1982) and 1.8 for the Amandelbult mine (Von Gruenewaldt et al. 1986). However, the PGE-rich sample UG2-4 from the top of the main seam has a high Pt/Pd ratio of 3.9. Another discriminant variable is the ratio of “palladium group elements” (PPGE: Pd + Pt + Rh) to “iridium-group elements” (IPGE: Ir + Os + Ru). Our 5PGE + Au assay data do not include Os, but data from the adjacent Amandelbult mine show that Os accounts for just 11 wt.% of the IPGE sum (Von Gruenewaldt et al. 1986), so its absence should not affect the PPGE/IPGE ratio by much. The PPGE/IPGE ratio in the Amandelbult UG2 averages 4.2 (Von Gruenewaldt et al. 1986). In comparison, the MD17 samples have considerably lower PPGE/IPGE ratios in the bottom and middle parts. (2.3–2.9) and a higher ratio (5.7) in the upper sample UG2-4. The PPGE/IPGE ratio in the upper leader (sample UG2-5) at Thaba mine is 4.3, similar to the value at Amandelbult. The chondrite-normalized pattern of PGE distribution in the upper leader sample corresponds closely with the regional average for UG2 (dashed black line in Fig. 4B).
Quantitative mineralogy
The MLA results of ore and gangue mineral assemblages are summarized in a bar chart in Fig. 5 in terms of the PGE, BMS, and gangue mineral groups. The MLA data are reported in Zhou et al. (2023). The typical PGE mineral assemblage of UG2 ore regionally is dominated (> 80 modal %) by sulfide minerals, comprising Pt and Pd sulfides, laurite (RuS2), and PGE-Cu sulfides (Kinloch 1982; Gain 1985; Penberthy et al. 2000; Voordouw et al. 2010; Fig. 5). In contrast, Pt–Pd sulfides and PGE-Cu sulfides make up just 10% or less of the UG2 ore assemblage in samples from drillcore MD17. Instead, the mineralogy is dominated by laurite, PGE alloys, PGE sulfarsenides, and PGE-bearing Sb–Bi–Te–Pb minerals. In detail, there are interesting differences in the abundance patterns of PGE minerals within the main seam. The lower section (MD17-04 through MD17-09) contains subequal amounts of laurite and PGE-alloys, with < 20% combined PGE sulfarsenides and Sb–Bi–Te–Pb minerals. Higher up in the seam, starting from sample MD17-23, the proportion of sulfarsenides and Sb–Bi–Te–Pb phases increases to 40% or more of the total PGE assemblage, while the relative abundance of laurite decreases. The PGE assemblage in samples MD17-40 and MD17-41 is rich in ferroplatinum and other alloys (40–50% of the total), which probably explains the uniquely high Pt/Pd and PPGE/IPGE ratios of their corresponding assay values (sample UG2-4, Table 1) compared to the rest of the main seam and upper leader. Interestingly, the PGE mineralogy of the upper leader (samples MD17-55 and MD17-56) is much different than that of the main seam, being dominated to about 80% by PGE sulfarsenide minerals. In this sense, the leader also stands in stark contrast to “normal” UG2 from the Amandelbult mine and elsewhere, but the assay values of PGE concentration and ratios (sample UG2-5) are unaffected by this change in the mineral assemblage.
The distribution of base-metal sulfide (BMS) minerals in the MD17 drillcore interval also varies within the UG2 seam as well as between it and the upper leader. Pentlandite and chalcopyrite dominate the BMS assemblage in UG2 regionally (McLaren and Villiers 1982; Voordouw et al. 2010; Langa et al. 2021), and this is the case for most samples of the main seam and upper leader of MD17, but the middle part of the main seam (samples MD17-23, MD17-24, MD17-30 and MD17-31), near IRUP-2 and IRUP-3, shows a local abundance of millerite, violarite, and secondary CuFeS phases at the expense of pentlandite and chalcopyrite. Notably, these are the same samples with the highest proportion of PGE sulfarsenide and Sb–Bi–Te–Pb-bearing phases in the main seam, as well as abundant alteration silicates and amphibole at the expense of pyroxene.
It is noted that the lowermost sample, MD17-04, is mostly within the chromitite but contains the IRUP contact at its base. Because of the negligible PGE contents in IRUP-1 (0.16 ppm; Table 1), the PGE mineralogy of this sample represents that of the chromitite layer alone, but the abundance and proportion of BMS and silicate phases reflect a mixture of both rock types and cannot be usefully interpreted.
Mineral compositions
To characterize the IRUP in drillcore MD17 and assess the variations in composition at the IRUP-UG2 contact, we determined the composition of oxide and silicate phases by electron microprobe analyses from three UG2-IRUP contacts: footwall IRUP-1 (samples MD17-01, MD17-03, MD17-04, MD17-05), IRUP-2 (MD17-14, MD17-15), and IRUP-3 (MD17-23, MD17-24, MD17-26, MD17-27). The analyzed samples also include the upper leader (MD17-55, MD17-56) and the hanging wall pyroxenite (MD17-58). All results are provided by Zhou et al. (2023).
Pyroxene
Clinopyroxene is abundant in the IRUP and has a uniform composition in all samples analyzed (Fig. 6). Clinopyroxene from IRUP-1, IRUP-2, and IRUP-3 yielded similar average Mg# values [Mg/(Mg + Fe2+) × 100] of 78 ± 2 (n = 13), 78 ± 2 (n = 21), and 80 ± 4 (n = 11), respectively. Scoon and Mitchell (1994) reported a considerably lower average Mg# of 66 for clinopyroxene from the Middellaagte IRUP body. It is possible that the higher Mg# in samples from MD17 reflects the fact that the IRUP here represents apophyses of the main body at its periphery. The interstitial clinopyroxene in the UG2 chromitite adjoining IRUP-1 and IRUP-3 has an average Mg# of 86 ± 2 (n = 13) and 84 ± 3 (n = 7), respectively, while the Mg# in the upper leader averages 90 ± 2 (n = 3). Similar values (Mg# of 86–88) were reported by Veksler et al. (2015) for interculumus clinopyroxene from the Upper Critical Zone between UG1 and the Merensky Reef at the Northam (west limb) and Nkwe (east limb) mines. No clinopyroxene was found in the hanging wall pyroxenite.
Orthopyroxene is rare in IRUP, and it was found only locally as small grains in IRUP-1 and IRUP-3. Analyses from IRUP-1 yielded an average Mg# of 68 ± 2 (n = 10), and a single analysis from IRUP-3 yielded an Mg# of 56. Orthopyroxene is the dominant phase in the hanging wall pyroxenite where it has an average Mg# of 79 ± 1 (n = 8), which is considerably more magnesian than in IRUP. Interstitial orthopyroxene compositions in UG2 adjoining IRUP-1 and IRUP-3 and in the upper leader have nearly the same Mg#, with average values of 85 (n = 1), 87 ± 3 (n = 5), and 85 ± 2 (n = 12), respectively. These values compare well with those of orthopyroxene from UG2 in other localities (e.g., Mg# = 89: Mondal and Mathez 2007; 88–91: Veksler et al. 2018).
Olivine
The three IRUP bodies contain olivine of similar composition. The average Fo values [Fo = Mg/(Mg + Fe) × 100] are 54 ± 3 (n = 5), 56 ± 3 (n = 16), and 58 ± 3 (n = 11) for IRUP-1, IRUP-2, and IRUP-3, respectively. These are slightly higher than the Fo32–50 for olivine in the Middellaagte IRUP body (Viljoen and Scoon 1985), which, as postulated above for clinopyroxene, may reflect the marginal position of our samples relative to the main IRUP body studied by those authors. Interstitial olivine in UG2 was analyzed from the lower section of the main seam adjoining IRUP-1 (Fo = 77 ± 3, n = 11) and from the upper leader (Fo = 84 ± 2, n = 6). Olivine in the hanging wall pyroxenite is rare; two analyses both gave a Fo value of 76. These results compare well with the Fo values of 79–85 reported elsewhere for olivine in pyroxenites from the Upper Critical Zone (Veksler et al. 2015; Mitchell et al. 2019a). Nickel contents in olivine from IRUP (< 0.1 wt.% NiO) are low compared with interstitial olivine in UG2 (0.2–0.5 wt.%) and in hanging wall pyroxenite (0.4 wt.%).
Plagioclase
Plagioclase is rare in IRUP generally (e.g., Viljoen and Scoon 1985), although Reid and Basson (2002) found ubiquitous interstitial plagioclase in IRUP from the Northam mine, with up to 15 vol.% locally. In our samples plagioclase was found only in the footwall IRUP-1. Plagioclase in this sample is surrounded by clinopyroxene and likely represents a relict phase. This is supported by the fact that the average anorthite component (An) in this sample is 80 ± 3 (n = 8), essentially the same as in the hanging wall pyroxenite (An = 83 ± 1, n = 5) and significantly lower than reported from other IRUP bodies nearby. Viljoen and Scoon (1985), Scoon and Mitchell (1994), and Reid and Basson (2002) found An values of 90 and above in plagioclase from the Middellaagte IRUP and in IRUP from Northam, respectively.
Hornblende and phlogopite
Hornblende is common in all three IRUP layers, and it has a uniform Mg# throughout (averages for IRUP-1, IRUP-2, and IRUP-3 are 66, 68, and 65, respectively). This is much more iron-rich than interstitial hornblende in the hanging wall pyroxenite (Mg# = 81 ± 1, n = 13) and in the UG2 (adjoining IRUP-3) and upper leader (85 and 83, respectively). Also distinctive for hornblende in IRUP are high concentrations of TiO2 (average 2.6, 1.8, and 2.1 wt.% in IRUP-1, IRUP-2, and IRUP-3, respectively) and K2O (1.1, 0.2, and 0.7 wt.% in IRUP-1, IRUP-2, and IRUP-3). These values for TiO2 and K2O are about twice those of interstitial hornblende in UG2 and in hanging wall pyroxenite.
Phlogopite was found as rare interstitial grains in IRUP-1 (Mg# = 70 ± 1, n = 3), and in hanging wall pyroxenite (Mg# = 88, n = 1). Interstitial phlogopite in UG2 was mostly chloritized, and only a few analyses of fresh grains were obtained in samples adjoining IRUP-1. These yielded an average Mg# of 82 ± 3 (n = 4), which is lower than the values (92–97) reported from studies of undisturbed UG2 (Mathez and Mey 2005; Mondal and Mathez 2007; Zhou et al. 2021), probably due to the IRUP influence.
Fe–Ti–Cr oxides
Ilmenite was found only in the IRUP bodies, not in UG2, and its composition is similar throughout except that MgO contents are lower in footwall IRUP-1 (average 1.6 wt.%) than in IRUP-2 and IRUP-3 that intrude the main seam (2.5 and 2.8 wt.% MgO, respectively). The contents of Cr2O3 in ilmenite are uniformly low (0.1–0.2 wt.%) in all samples, independent of their location.
Spinel phases are common in all lithologies studied. The spinel compositions are highly diverse in terms of Mg# [Mg/(Mg + Fe2+) × 100], Cr# [Cr/(Cr + Al) × 100], and TiO2 concentration (Figs. 7 and 8). The variations of Cr–Al–Fe–Mg–Ti contents define continuous trends between what has been referred to as “unusual Fe–Ti–Cr spinel” (Scoon and Eales 2002) and Ti-magnetite on the one hand and chromite on the other (Fig. 7). The Fe–Ti–Cr spinel occurs at IRUP-UG2 contacts on the IRUP side, with a lesser amount in the adjoining UG2 layer (see next section). The overall composition range of Fe–Ti-Cr spinel is Mg# = 2–12, Cr# = 35–69, and TiO2 = 4.8–15.2 wt.%. The corresponding range in UG2 chromite is Mg# = 11–37, Cr# = 55–67, and TiO2 = 0.7–5.3 wt.%. The chromite in the upper leader has a more uniform composition, with Mg# = 29–39, Cr# = 58–61, and TiO2 = 0.8–1.0 wt.%. Finally, interstitial chromite in the pyroxenite hanging wall has a composition similar to that of the upper leader, with Mg# = 20–30, Cr# = 54–65, and TiO2 = 0.6–2.3 wt.%.
The comparison of the chromite Mg# and TiO2 contents in UG2 from this study and from other localities in the complex (Fig. 8) shows that TiO2 concentrations in the main seam and upper leader at Thaba mine reach values typical for UG2 regionally, but the Mg# is 5 to 10% lower than typical UG2. We interpret the pervasively low Mg# in chromite as an effect of IRUP interaction, as noted above for the interstitial olivine, pyroxene, hornblende, and phlogopite in UG2.
Element mapping of the UG2-IRUP contact
Back-scatter electron (BSE) micrographs and micro-XRF element maps of thin sections across the contacts of all three IRUP bodies with UG2 show important details of their interaction. The precise original contact is not easy to locate because of a silicate-free zone of Fe–Ti oxide minerals (ilmenite and Fe–Ti–Cr spinel) that appears to grade into the chromitite of UG2 (Cameron and Glover 1973; Scoon and Eales 2002). Since ilmenite is not known to form in UG2 except for rare, fine-grained exsolutions in chromite (e.g., Junge et al. 2014), we defined the original contact at the limit of abundant ilmenite grains, which is a few millimeters beyond the limit of the IRUP silicate minerals. Figure 9 shows element maps and electron microprobe profiles of spinel composition across the UG2 contact with IRUP-1. Corresponding profiles across the IRUP-2 and IRUP-3 contacts are presented in Zhou et al. (2023). All contacts examined show similar features.
The IRUP side is characterized by ilmenite and Fe–Ti–Cr spinel intergrowths, whereby the spinel phase shows strong variations in Cr, Ti, Fe, and Mg# (Figs. 7 and 8). In detail, there are complex microtextural relations between the newly formed ilmenite and Fe–Ti–Cr spinel in this replacement layer (Fig. 10). Locally, the two phases appear to form symplectic intergrowths, and ilmenite is commonly rimmed by a third phase, which is dark in BSE images (Figs. 10B, C). These dark rims are 1–10 μm thick and too small for quantitative analysis, but EPMA element mapping shows that they have lower Fe and Ti and higher Cr and Mg contents than the associated Fe–Ti–Cr spinel grains, while qualitative analysis by EDS indicates that Al is also a major constituent. Cameron and Glover (1973) and Scoon and Eales (2002) described similar microtextures in the oxide layer formed in IRUP at contact with chromitite. The latter study attributed the symplectic intergrowths of ilmenite and Fe–Ti–Cr spinel to coarsening of an exsolution texture and also identified the dark rims on ilmenite as Al-spinel.
The UG2 side of the contact is characterized by the larger grain size of chromitite grains, the formation of a lesser amount of Fe–Ti–Cr spinel, and the loss of interstitial silicates and sulfide minerals, which is particularly visible in the BSE images and micro-XRF maps of Mg and S distribution (Figs. 9B and 10A). Also, there are smooth concentration gradients in Cr, Al, Fe, and Ti within the chromitite that are parallel to the contact (Fig. 9B). The element maps suggest that the gradients extend a few millimeters from the contact, but the EPMA profiles demonstrate that the chemical effects of IRUP interaction extend into the chromitite for up to about 5 cm beyond the contact (Fig. 9A). Similar concentration gradients of Cr and Ti in chromite were documented by Mitchell et al. (2019a) by micro-XRF scanning of the UG2-IRUP contact at the Wilgerspruit locality to the SW of our study area (Fig. 1). Mitchell et al. (2019a) also described coarsening of chromite grains and loss of interstitial phases (“sintering” in their terminology). These centimeter-scale effects are referred to as “local,” but it is important to note that throughout most of the main UG2 seam in drillcore MD17, chromite compositions show higher TiO2 contents than normal for UG2 (< 2 wt.% as shown in Fig. 7).
Discussion
Transformation of chromite to Fe–Ti–Cr spinel
Several studies in the Bushveld Complex noted the presence of unusual spinel compositions in places where IRUP intrudes chromitite and interpreted them as recrystallization or replacement of former chromite grains (Cameron and Glover 1973; Viljoen and Scoon 1985; Scoon and Mitchell 1994; Scoon and Eales 2002). This is also the case in our study, as shown by the textural changes and concentration gradients in UG2 chromitite (Fig. 9). Importantly, Fe–Ti–Cr spinel formed on the IRUP side of the contract where chromite was absent, and the modal amount of oxide minerals in this zone is much greater than can be explained by replacement of Ti-magnetite and ilmenite in normal IRUP. Furthermore, an oxide layer formed at UG2 contacts in all three IRUP bodies in MD17, regardless of their thickness (Fig. 10; Zhou et al. 2023). We suggest that the oxide layer crystallized in situ from the IRUP melt. Possibly, as suggested by Scoon and Eales (2002), the refractory chromitite layers acted to channel and pool the IRUP melt at their contacts, where Fe–Ti–Cr spinel and ilmenite crystallized at the chromitite interface. Subsequent cooling caused recrystallization and/or equilibration within and across the oxide layers, resulting in exsolution textures, grain coarsening, chemical gradients in chromitite, and the “unusual” Fe–Ti–Cr spinel compositions that seem unique to the chromitite-IRUP contact zones in Bushveld. Indeed, the range of spinel compositions reported by Scoon and Eales (2002) coincides remarkably with our results from borehole MD17 (Fig. 7), and they also reported similar spinel-ilmenite intergrowths in association with Fe–Ti–Cr spinel compositions at chromitite contacts in the Merensky Reef as found in our study of UG2 (Fig. 10C).
The effects of IRUP on UG2 mineralization
Our MLA results and whole-rock assay values from the UG2 profile in borehole MD17, in comparison with IRUP-free localities, show significant changes in ore mineralogy (Fig. 5) and redistribution of PGE within the layer, which we attribute to the effects of IRUP interaction. However, the overall grade of UG2 appears not to have been affected. Thus, the average 5PGE + Au concentration in 5 samples from the main seam is 5.9 ppm, which is similar to that of the upper leader (5.3 ppm) and close to the 6.5 ppm reported from the nearby Amandelbult mine (Von Gruenewaldt et al. 1986). Previous work indicates a range of PGE grades from 4 to 10 ppm for UG2 regionally (Mclaren and De Villiers 1982; Gain 1985; Von Gruenewaldt et al. 1986; Penberthy and Merkle 1999; Cawthorn et al. 2002; Maier and Barnes 2008; Voordouw et al. 2009; Junge et al. 2014; Osbahr et al. 2014). On the other hand, a typical feature of UG2 in the Bushveld Complex, including Amandelbult, is a concentration of PGE in the lower part, where contents typically exceed 10 ppm (Fig. 11). This feature is missing at MD17 from the Thaba mine, where the basal sample UG2-1 yielded 5.9 ppm 5PGE + Au, about half of the maximum 11.4 ppm found near the top of the main seam. We cannot rule out that the base of UG2 at Thaba mine was originally less mineralized than in other localities, but it seems more likely that interaction with the footwall IRUP caused a loss of PGE from the base. This is supported by the textural and mineralogical changes at the IRUP-UG2 contacts described above and the MLA results that show correlated changes in the ore mineral assemblages (PGE and BMS minerals) as well as the interstitial silicate phases (Fig. 5).
The regional PGE mineralogy of UG2 is dominated by Pt and Pd sulfides, Ru sulfide (laurite), and PGE-Cu sulfides (McLaren and De Villiers 1982; Osbahr et al. 2014). Indeed, these phases make up 85% of the PGE assemblage at Amandelbult, according to Kinloch (1982). In contrast, the only abundant PGE sulfide in UG2 at Thaba mine is laurite, while most PGEs are contained in PGE alloys, sulfarsenides, and PGE-bearing Bi–Te–Sb phases. In this respect the Thaba UG2 resembles the IRUP- “affected” UG2 ore from the Brits-Marikana area, southwestern Bushveld (Penberthy and Merkle 1999; Penberthy et al. 2000; Fig. 5). The low proportion of primary PGE sulfide minerals near IRUP in MD17 can be caused by the grain coarsening and loss of interstitial phases in the chromitite (e.g., Fig. 9), as noted in other studies (Scoon and Eales 2002; Mitchell et al. 2019a). Interestingly, the proportion of laurite in “normal” UG2 vs. “affected” UG2 (related to IRUP, faults, and potholes) from comparative studies is about the same (20–30% of the PGE assemblage), and this is also true for the base of UG2 at Thaba mine (Fig. 5). The survival of laurite probably owes to its presence as inclusions in chromite (e.g., Kinloch 1982; McLaren and De Villiers 1982).
The vertical distribution of PGE, BMS, and gangue mineral assemblages within the UG2 layer (Fig. 5) shows correlations that shed light on how the layer was affected by IRUP. The middle part of the main seam, near IRUP-2 and IRUP-3, is enriched in interstitial amphibole and “alteration silicates” (chlorite, serpentine, talc) at the expense of pyroxene. This abundance of hydrous silicates in the chromitite interstitial network is a sign that UG2 was metasomatized by hydrothermal fluid. Also, there is an almost complete lack of interstitial plagioclase in the whole UG2 layer, whereas plagioclase is important or dominant in the interstitial silicates of “normal” UG2 (Mathez and Mey 2005; Voordouw et al. 2010; Veksler et al. 2018; Mitchell et al. 2019a). Destruction of plagioclase in rocks partially replaced by IRUP is common (Viljoen and Scoon 1985; Reid and Basson 2002), and we suspect that the anomalously low plagioclase abundance in UG2 from MD17 is an effect of IRUP interaction. Pentlandite and chalcopyrite are the dominant primary BMS minerals in normal UG2 elsewhere (Fig. 5), but samples near IRUP-2 and IRUP-3 contain very little chalcopyrite and significant amounts of secondary Ni–Fe sulfides (millerite, violarite) at the expense of pentlandite. We consider it significant that the part of the main seam showing an abundance of secondary Ni–FE and Cu–Fe sulfide minerals is also rich in hydrous silicates and in PGE sulfarsenides and Sb–Bi–Te–Pb phases (samples MD17-23 to MD17-41; Fig. 5). Although there is no IRUP intersection near the upper leader in borehole MD17, the PGE mineralogy there is dominated by secondary PGE sulfarsenides and Sb–Bi–Te–Pb phases. Considering the location of borehole MD17 with respect to the Middellaagte IRUP body and the abundance of smaller IRUPs in the region (Fig. 2A), we can speculate that other IRUP bodies may be close by but not present in the drillcore. On the other hand, it must be noted that secondary ore assemblages and hydrous silicates in UG2 similar to those described here are found in places that are apparently free of IRUP but affected by faults and potholes (McLaren and De Villiers 1982; Kinloch and Peyerl 1990; Penberthy and Merkle 1999; Voordouw et al. 2010). What these settings have in common is that they enhanced the access of hydrothermal fluids to the UG2 layer. A comparison can also be drawn to the “UG2 equivalent” (UG2E) layer on the Bushveld northern limb described by Langa et al. (2021). Here, too, the PGE assemblages are dominated by alloys and As–Bi–Te phases, and the BMS assemblage contains significant amounts of pyrrhotite at the expense of the otherwise typical pentlandite–chalcopyrite association. IRUP bodies are unknown from this locality, and the authors suggested that the particular features of the UG2E chromitite were caused by the magmatic assimilation of Transvaal Group country rocks.
In summary, we distinguish two sets of phenomena caused by UG2-IRUP interaction at the Thaba mine, which operated at different scales. The small-scale effects are limited to the immediate IRUP-UG2 contact and include crystallization of a layer with Fe–Ti–Cr spinel intergrown with ilmenite on the IRUP side and coarsening, recrystallization, and chemical gradients within chromitite on the UG2 side. We propose that these effects were caused by the interaction of IRUP melt with the solidified UG2, possibly aided by ponding of the melt at the chromitite contact as envisioned by Scoon and Eales (2002). Grain coarsening and “sintering” during this process probably caused a loss of interstitial sulfides and PGE grade from the basal part of UG2, which is typically the richest zone in “normal” UG2. On a larger scale, the IRUP interaction affected most of the main seam and the upper leader. Evidence includes the anomalous chromite composition (elevated TiO2 contents, lower Mg#), the unusually low abundance of interstitial plagioclase, the formation of hydrous silicates and secondary PGE- and Ni–Cu–Fe sulfide minerals, and the lowering of the Mg# of the mafic silicates (e.g., phlogopite). We suggest that these large-scale effects were caused by hydrothermal fluids derived from IRUP melts.
From an economic standpoint, the IRUP interaction with UG2 at the Thaba mine did not significantly reduce the overall PGE grade, causing only a redistribution of grade within the layer. However, significant changes in the ore mineralogy of IRUP-affected UG2 (replacement of PGE sulfides by alloys and PGE-bearing As-Sb-Bi-Te-Pb phases) and in the gangue assemblage (secondary talc, serpentinite) will decrease the efficiency of PGE recovery when using conventional flotation techniques (Kinloch 1982; Peyerl 1982; Penberthy et al. 2000; Bachmann et al. 2018).
Conclusions
Three IRUP bodies intersect the UG2 chromitite in borehole MD17 from the Thaba mine in the northwestern Bushveld Complex: one at the footwall and two within the main chromitite seam. These IRUPs are interpreted as the apophyses of the large Middellaagte body, a disc-shaped IRUP some 1.5 km in diameter. The studied IRUPs consist of clinopyroxene (Mg# = 78–80) and olivine (Fo54–58) with minor hornblende, ilmenite, Ti-magnetite, and accessory iron sulfides. All contacts of IRUP and UG2 in this study display an oxide layer a few millimeters thick that formed on the IRUP side and consists of intergrowths of ilmenite and compositionally diverse Fe–Ti–Cr spinel, with microtextures suggesting exsolution during cooling. On the UG2 side of the contact, there is an increase in the grain size of chromite with concomitant destruction of interstitial phases, including sulfide minerals. Additionally, the chromite composition shows contact-parallel gradients in Ti, Fe, Cr, and Al that extend a few centimeters into the UG2 layer. We attribute these features to the crystallization of an oxide layer from the IRUP melt onto the solidified chromitite interface, followed by re-equilibration and chemical exchange on both sides during cooling.
Quantitative mineral assemblage analysis by MLA and bulk-rock PGE assays show strong effects of IRUP interaction on the PGE mineralogy and redistribution of grade within the UG2 seam with little or no net loss. The average grade of 5PGE + Au (5.9 ppm) is similar to that of unaffected UG2 in the nearby Amandelbult mine and regionally. However, while typical UG2 ore is dominated by PGE sulfide minerals, pentlandite and chalcopyrite, the ore assemblage at Thaba mine is dominated by PGE alloys, sulfarsenides, and Sb–Bi–Te–Pb phases, and there is a significant proportion of secondary Ni–sulfide phases at the expense of pyroxene. These changes in the ore assemblage of UG2 are associated with an abundance of interstitial hornblende and secondary hydrous silicates at the expense of pyroxene. We attribute these meter-scale effects to hydrothermal fluids released from the IRUP melt.
Our results demonstrate that IRUP interaction with UG2 has not destroyed the overall PGE grade, but there is likely to be a significant loss of value because of the replacement of primary PGE sulfides by alloys and PGE-bearing As–Sb–Bi–Te–Pb minerals, along with the formation of alteration silicates. These will have a negative impact on the PGE recovery by flotation.
References
Bachmann K, Frenzel M, Krause J, Gutzmer J (2017) Advanced identification and quantification of in-bearing minerals by scanning electron microscope-based image analysis. Microsc Microanal 23:527–537. https://doi.org/10.1017/s1431927617000460
Bachmann K, Osbahr I, Tolosana-Delgado R, Chetty D, Gutzmer J (2018) Variation in platinum group mineral and base metal sulfide assemblages in the Lower Group chromitites of the western Bushveld Complex, South Africa. Can Mineral 56:723–743. https://doi.org/10.3749/canmin.1700094
Bachmann K, Menzel P, Tolosana-Delgado R, Schmidt C, Hill M, Gutzmer J (2019) The use of assay data as a foundation for a geometallurgical model—the case of the Thaba Chromite Mine, South Africa. J Geochem Explor 201:99–112. https://doi.org/10.1016/j.gexplo.2019.01.008
Barnes S-J, Maier WD (2002) Platinum-group element distributions in the Rustenburg Layered Suite of the Bushveld Complex, South Africa. In: Cabri LJ (ed) The geology, geochemistry, mineralogy and mineral beneficiation of platinum-group elements, special, vol 54. Canadian Institute of Mining. Metallurgy and Petroleum, Montreal, pp 431–458
Cameron EN, Desborough GA (1964) Origin of certain magnetite-bearing pegmatites in the eastern part of the Bushveld complex, South Africa. Econ Geol 59:197–225. https://doi.org/10.2113/gsecongeo.59.2.197
Cameron EN, Glover ED (1973) Unusual titanian-chromian spinels from the eastern Bushveld Complex. Am Miner 58:172–188
Cawthorn RG, Harris C, Kruger FJ (2000) Discordant ultramafic pegmatoidal pipes in the Bushveld Complex. Contrib Miner Petrol 140:119–133. https://doi.org/10.1007/s004100000175
Cawthorn RG, Lee CA, Schouwstra RP, Mellowship P (2002) Relationship between PGE and PGM in the Bushveld Complex. Can Mineral 40:311–328. https://doi.org/10.2113/gscanmin.40.2.311
Cawthorn RG, Latypov R, Klemd R, Vuthuza A (2018) Origin of discordant ultramafic pegmatites in the Bushveld Complex from externally-derived magmas. S Afr J Geol 121:287–310. https://doi.org/10.25131/sajg.121.0027
Cawthorn RG (2015) The bushveld complex, South Africa. In: Charlier B, Namur O, Latypov R, Tegner C (eds) Layered Intrusions. Springer Netherlands, Dordrecht, pp 517–587. https://doi.org/10.1007/978-94-017-9652-1_12
Fandrich R, Gu Y, Burrows D, Moeller K (2007) Modern SEM-based mineral liberation analysis. Int J Miner Process 84:310–320. https://doi.org/10.1016/j.minpro.2006.07.018
Gain SB (1985) The geologic setting of the platiniferous UG-2 chromitite layer on the farm Maandagshoek, eastern Bushveld Complex. Econ Geol 80:925–943. https://doi.org/10.2113/gsecongeo.80.4.925
Junge M, Oberthür T, Melcher F (2014) Cryptic variation of chromite chemistry, platinum group element and platinum group mineral distribution in the UG2 chromitite: an example from the Karee Mine, western Bushveld Complex, South Africa. Econ Geol 109:795–810. https://doi.org/10.2113/econgeo.109.3.795
Kaufmann FED, Hoffmann MC, Bachmann K, Veksler IV, Trumbull RB, Hecht L (2019) Variations in composition, texture, and platinum group element mineralization in the Lower Group and Middle Group chromitites of the northwestern Bushveld Complex, South Africa. Econ Geol 114:569–590. https://doi.org/10.5382/econgeo.4641
Kinloch ED (1982) Regional trends in the platinum-group mineralogy of the critical zone of the Bushveld Complex, South Africa. Econ Geol 77:1328–1347. https://doi.org/10.2113/gsecongeo.77.6.1328
Kinloch ED, Peyerl W (1990) Platinum-group minerals in various rock types of the Merensky Reef; genetic implications. Econ Geol 85:537–555. https://doi.org/10.2113/gsecongeo.85.3.537
Kinnaird JA, Kruger FJ, Nex PAM, Cawthorn RG (2002) Chromitite formation—a key to understanding processes of platinum enrichment. Appl Earth Sci 111:23–35. https://doi.org/10.1179/aes.2002.111.1.23
Kinnaird JA, Hutchinson D, Schurmann L, Nex PAM, de Lange R (2005) Petrology and mineralisation of the southern Platreef: northern limb of the Bushveld Complex, South Africa. Miner Deposita 40:576–597. https://doi.org/10.1007/s00126-005-0023-9
Langa MM, Jugo PJ, Leybourne MI, Grobler DF (2021) Sulfide mineral chemistry and platinum-group minerals of the UG-2 chromitite in the northern limb of the Bushveld Igneous Complex, South Africa. Can Mineral 59:1339–1362. https://doi.org/10.3749/canmin.2100042
Latypov R, Chistyakova S, Mukherjee R (2017) A novel hypothesis for origin of massive chromitites in the Bushveld Igneous Complex. J Petrol 58:1899–1940. https://doi.org/10.1093/petrology/egx077
Latypov R, Costin G, Chistyakova S, Hunt EJ, Mukherjee R, Naldrett T (2018) Platinum-bearing chromite layers are caused by pressure reduction during magma ascent. Nat Commun 9:462. https://doi.org/10.1038/s41467-017-02773-w
Maier W, Barnes S-J (2008) Platinum-group elements in the UG1 and UG2 chromitites, and the Bastard reef, at Impala platinum mine, western Bushveld Complex, South Africa: Evidence for late magmatic cumulate instability and reef constitution. S Afr J Geol 111:159–176. https://doi.org/10.2113/gssajg.111.2-3.159
Mathez EA, Mey JL (2005) Character of the UG2 chromitite and host rocks and petrogenesis of its pegmatoidal footwall, northeastern Bushveld Complex. Econ Geol 100:1617–1630. https://doi.org/10.2113/gsecongeo.100.8.1617
McDonough WF, Sun SS (1995) The composition of the Earth. Chem Geol 120:223–253. https://doi.org/10.1016/0009-2541(94)00140-4
McLaren CH, De Villiers JPR (1982) The platinum-group chemistry and mineralogy of the UG-2 chromitite layer of the Bushveld Complex. Econ Geol 77:1348–1366. https://doi.org/10.2113/gsecongeo.77.6.1348
Mitchell AA, Henckel J, Mason-Apps A (2019a) The Upper Critical Zone of the Rustenburg Layered Suite in the Swartklip Sector, north-western Bushveld Complex, on the farm Wilgerspruit 2JQ: I. Stratigraphy and PGE mineralization patterns. S Afr J Geol 122:117–142. https://doi.org/10.25131/sajg.122.0010
Mitchell AA, Scoon RN, Sharpe MR (2019b) The Upper Critical Zone in the Swartklip Sector, north-western Bushveld Complex, on the farm Wilgerspruit 2JQ: II. Origin by intrusion of ultramafic sills with concomitant partial melting of host norite-anorthosite cumulates. S Afr J Geol 122:143–162. https://doi.org/10.25131/sajg.122.0011
Mondal SK, Mathez EA (2007) Origin of the UG2 chromitite layer, Bushveld Complex. J Petrol 48:495–510. https://doi.org/10.1093/petrology/egl069
Naldrett AJ, Wilson A, Kinnaird J, Yudovskaya M, Chunnett G (2012) The origin of chromitites and related PGE mineralization in the Bushveld Complex: new mineralogical and petrological constraints. Miner Deposita 47:209–232. https://doi.org/10.1007/s00126-011-0366-3
Osbahr I, Oberthür T, Klemd R, Josties A (2014) Platinum-group element distribution in base-metal sulfides of the UG2 chromitite, Bushveld Complex, South Africa—a reconnaissance study. Miner Deposita 49:655–665. https://doi.org/10.1007/s00126-014-0538-z
Penberthy CJ, Merkle RKW (1999) Lateral variations in the platinum-group element content and mineralogy of the UG2 Chromitite Layer, Bushveld Complex. S Afr J Geol 102:240–250
Penberthy CJ, Oosthuyzen EJ, Merkle RKW (2000) The recovery of platinum-group elements from the UG-2 chromitite, Bushveld Complex – a mineralogical perspective. Mineral Petrol 68:213–222. https://doi.org/10.1007/s007100050010
Peyerl W (1982) The influence of the Driekop dunite pipe on the platinum-group mineralogy of the UG-2 chromitite in its vicinity. Econ Geol 77:1432–1438. https://doi.org/10.2113/gsecongeo.77.6.1432
Reid DL, Basson IJ (2002) Iron-rich ultramafic pegmatite replacement bodies within the Upper Critical Zone, Rustenburg Layered Suite, Northam Platinum Mine, South Africa. Mineral Mag 66:895–914. https://doi.org/10.1180/0026461026660066
Scoates JS, Wall CJ, Friedman RM, Weis D, Mathez EA, VanTongeren JA (2021) Dating the Bushveld Complex: timing of crystallization, duration of magmatism, and cooling of the world’s largest layered intrusion and related rocks. J Petrol 62:egaa107. https://doi.org/10.1093/petrology/egaa107
Scoon RN, Eales HV (2002) Unusual Fe-Ti-Cr spinels from discordant bodies of iron-rich ultramafic pegmatite at the Amandelbult Platinum mine, northwestern Bushveld Complex. Mineral Mag 66:857–879. https://doi.org/10.1180/0026461026660064
Scoon RN, Mitchell AA (1994) Discordant iron-rich ultramafic pegmatites in the Bushveld Complex and their relationship to iron-rich intercumulus and residual liquids. J Petrol 35:881–917. https://doi.org/10.1093/petrology/35.4.881
Scoon RN, Mitchell AA (2004) The platiniferous dunite pipes in the eastern limb of the Bushveld Complex: Review and comparison with unmineralized discordant ultramafic bodies. S Afr J Geol 107:505–520. https://doi.org/10.2113/gssajg.107.4.505
Scoon RN, Mitchell AA (2011) The principal geological features of the Mooihoek platiniferous dunite pipe, eastern limb of the Bushveld Complex, and similarities with replaced Merensky Reef at the Amandelbult Mine, South Africa. S Afr J Geol 114:15–40. https://doi.org/10.2113/gssajg.114.1.15
Scoon RN, Mitchell AA (2021) Discussion of “Crustal fluid contamination in the Bushveld Complex, South Africa: an analogue for subduction zone fluid migration by Benson, E., Connolly, J.A.D. and Boudreau, A.E. (2020). Int Geol Rev 63:2279–2286. https://doi.org/10.1080/00206814.2020.1830443
Scoon RN, Costin G, Gräbe PJ (2017) Geology and origin of the vanadiferous Fe-Ti oxide-rich Kennedy’s Vale discordant body, eastern limb of the Bushveld Complex, South Africa. S Afr J Geol 120:251–270. https://doi.org/10.25131/gssajg.120.2.251
Veksler IV, Hou T (2020) Experimental study on the effects of H2O upon crystallization in the Lower and Critical Zones of the Bushveld Complex with an emphasis on chromitite formation. Contrib Miner Petrol 175:85. https://doi.org/10.1007/s00410-020-01733-w
Veksler IV, Reid DL, Dulski P, Keiding JK, Schannor M, Hecht L, Trumbull RB (2015) Electrochemical processes in a crystal mush: cyclic units in the Upper Critical Zone of the Bushveld Complex, South Africa. J Petrol 56:1229–1250. https://doi.org/10.1093/petrology/egv036
Veksler IV, Sedunova AP, Darin AV, Anosova MO, Reid DL, Kaufmann FED, Hecht L, Trumbull RB (2018) Chemical and textural re-equilibration in the UG2 chromitite layer of the Bushveld Complex, South Africa. J Petrol 59:1193–1216. https://doi.org/10.1093/petrology/egy058
Viljoen M (2016) The Bushveld Complex - Host to the world’s largest platinum, chromium and vanadium resources. Episodes 39:238–268. https://doi.org/10.18814/epiiugs/2016/v39i2/95777
Viljoen MJ, Scoon RN (1985) The distribution and main geologic features of discordant bodies of iron-rich ultramafic pegmatite in the Bushveld Complex. Econ Geol 80:1109–1128. https://doi.org/10.2113/gsecongeo.80.4.1109
Viring RG, Cowell MW (1999) The Merensky Reef on Northam Platinum Limited. S Afr J Geol 102:192–208
Von Gruenewaldt G, Hatton CJ, Merkle RKW (1986) Platinum-group element-chromitite associations in the Bushveld Complex. Econ Geol 81:1067–1079. https://doi.org/10.2113/gsecongeo.81.5.1067
Voordouw R, Gutzmer J, Beukes NJ (2009) Intrusive origin for Upper Group (UG1, UG2) stratiform chromitite seams in the Dwars River area, Bushveld Complex, South Africa. Mineral Petrol 97:75–94. https://doi.org/10.1007/s00710-009-0072-3
Voordouw RJ, Gutzmer J, Beukes NJ (2010) Zoning of platinum group mineral assemblages in the UG2 chromitite determined through in situ SEM-EDS-based image analysis. Miner Deposita 45:147–159. https://doi.org/10.1007/s00126-009-0265-z
Zhou HY, Trumbull RB, Veksler IV, Bindeman IN, Glodny J, Kaufmann FED, Rammlmair D (2021) Contamination of the Bushveld Complex (South Africa) magmas by basinal brines: Stable isotopes in phlogopite from the UG2 chromitite. Geology 49:1272–1276. https://doi.org/10.1130/g49173.1
Zhou HY, Appelt O, Tjallingii R, Bachmann K, Trumbull RB (2023) Quantitative mineralogy, mineral chemistry and microtextural data on the UG2 chromitite intruded by iron-rich ultramafic pegmatite (IRUP) at the Thaba Mine, northwestern Bushveld Complex South Africa. GFZ Data Serv. https://doi.org/10.5880/GFZ.3.1.2022.005
Acknowledgements
The senior author’s stay at the GFZ Potsdam was supported by the German Academic Exchange Service (DAAD). Ilya Veksler acknowledges support from DFG grant VE 619-6-1. This study is a contribution of the Applied Mineralogy for Resource Efficiency of Platinum Metals (AMREP) project funded by the German Federal Ministry of Education and Research (BMBF grant 033R119). We are grateful to Moritz Hill and the staff of Cronimet Chrome Mining SA (Pty) Ltd. for access to the mine property and for providing drillcore samples and borehole logs that made this work possible. We acknowledge preliminary work on the MD17 core samples by Frank Rosendahl (MSc, University of Potsdam), and we thank Franziska Wilke (GFZ Potsdam) for expert help with EPMA analyses and Rik Tjallingii (GFZ Potsdam) for the micro-XRF element mapping. We are grateful to Roger Scoon and an anonymous reviewer for constructive comments that improved the paper and to Georges Beaudoin and Wolfgang Maier for editorial handling.
Funding
Open access funding provided by University of Oslo (incl Oslo University Hospital)
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare no conflict of interest.
Additional information
Editorial handling: G. Beaudoin
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhou (周浩阳), H., Trumbull, R.B., Veksler, I.V. et al. The effects of iron-rich ultramafic pegmatite on the composition and mineralogy of the UG2 chromitite: a case study in the western Bushveld Complex, South Africa. Miner Deposita 58, 1005–1021 (2023). https://doi.org/10.1007/s00126-023-01167-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00126-023-01167-x