Abstract
This review describes the use of an experimental technique known as electron back-scatter diffraction (EBSD) to measure microtexture, that is, spatially specific texture measured on an individual orientation basis. Other methods of microtexture determination are briefly described and compared with EBSD. The EBSD technique itself is described in considerable detail including recent developments such as on-line automation. Those EBSD-based microtexture studies which have been reported in the literature are summarized, including those which provide a direct comparison with macrotexture measurements obtained by X-ray diffraction. The concept of microtexture as the texture of individual grains leads naturally to the idea of “mesotexture” as the texture of grain boundaries. Mesotexture data can be computed from the EBSD-generated microtexture measurements and this is demonstrated and examples are given. Examples of microtexture/mesotexture studies in multiphase materials are also shown. Finally, because EBSD allows the simultaneous determination of microtexture/mesotexture and microstructural information, it is pertinent to discuss ways of displaying this sort of data, and so the review is completed by a discussion of the representation of microtextures and mesotextures, including the use of Rodrigues-Frank space and orientation mapping.
Similar content being viewed by others
References
H. J. Bunge, “Mathematische Methoden der Texturanalyse” (Akademie-Verlag, Berlin, 1969).
K. Lucke, in “Proceedings of the 6th International Conference on Textures of Materials (ICOTOM6)”, edited by S. Nagashima (ISI Japan, Tokyo, 1981) p. 14.
H. J. Bunge, “Texture Analysis in Materials Science” (translated by P. R. Morris) (Butterworths, London, 1982).
H. R. Wenk (ed.), “Preferred Orientation in Deformed Metals and Rocks: an Introduction to Modern Texture Analysis” (Academic Press, London, 1985).
M. Hatherley andW. B. Hutchinson, “An Introduction to Textures in Metals”, Institution of Metallurgists Monograph No. 5 (Chameleon Press, London, 1979).
F. J. Humphreys,Tex. Micros. 6 (1983) 45.
Idem, in “Proceedings of the 5th Riso Symposium”, edited by N. Hessel Anderson, M. Eldrup, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt, O. B. Pedersen and B. N. Singh (Riso National Laboratory Press, Denmark, 1984) p. 35.
R. A. Schwarzer andH. Weiland, in “Experimental Techniques of Texture Analysis”, edited by H. J. Bunge (DGM Informationsgesellschraft Verlag, Oberursel, 1986) p. 287.
R. A. Schwarzer andH. Weiland, in Proceedings of ICOTOM8”, edited by J. S. Kallend and G. Gottstein (AIME, Warrendale, PA, 1988) p. 203.
R. A. Schwarzer, in “Proceedings of ICOTOM9”,Tex. Mic. 14–18 (1991) 85.
D. J. Dingley,Phys. Bull. 36 (1985) 3.
J. A. Venables andC. J. Harland,Phil. Mag. 27 (1973) 1193.
J. A. Venables andR. Bin Jaya,ibid. 35 (1977) 1317.
D. G. Coates,ibid. 16 (1967) 1179.
D. C. Joy, in “Quantitative Scanning Electron Microscopy”, edited by D. B. Holt, M. D. Muir, P. R. Grant and I. M. Boswarva (Academic Press, London, 1974) p. 131.
D. L. Davidson, in “Proceedings of the 36th Annual Meeting EMSA” (Claitors Press, Baton Rouge, 1976) p. 402.
S. Nagagawa, in “Proceedings of the XIth International Congress on Electron Microscopy”, Vol. 35, Kyoto, edited by T. Imura, S. Maruse, T. Suzuki (Japanese Society for Electron Microscopy, Tokyo, 1986) p. 761.
S. Vale, in Institute of Physics Conference Series no. 78, “EMAG 85”, edited by G. J. Tatlock (Adam Hilger, Bristol, 1985) p. 79.
J. Harase andR. Shimizu, in “Proceedings of the 10th Riso Symposium”, edited by J. B. Bilde-Sorensen, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt and O. B. Pedersen (Riso National Laboratory Press, 1989) p. 365.
J. Harase, R. Shimizu andT. Watanabe, in “Proceedings of ICOTOM8”, edited by J. S. Kallend and G. Gottstein (Metals Society Inc., PA, 1988) pp. 723, 729.
Y. Inokuti andR. D. Doherty,Acta Metall. 26 (1978) 61.
D. J. Dingley,Scanning 1 (1978) 79.
D. J. Dingley, C. Harper andS. Long, in “Proceedings of the Institute of Physics Conference Series”, 61 (Adam Hilger, Bristol, 1981) p. 63.
M. N. Alam, M. Blackman andD. W. Pashley,Proc. R. Soc. 221A (1954) 224.
D. J. Dingley,Scan. Elect. Microsc. 11 (1984) 74.
Idem, in “Proceedings of ICOTOM8”, edited by J. S. Kallend and G. Gottstein (Metals Society Inc., PA, 1988) p. 189.
J. Harase, T. Shimizu, D. J. Dingley andY. Arai,Jpn Inst. Metals Conf. Ser. 62 (1987) 502.
D. J. Dingley, M. Longdon, J. Wienbren andJ. Alderman,Scan. Elect. Microsc. 1,2 (1987) 451.
K. Baba-Kishi, PhD thesis, University of Bristol (1986).
J. B. Buras, A. R. Hanson, E. M. Risemsan,Trans. IEEE P AMI 8 (1986) 425.
A. Day, private communication (1989).
D. Juul Jensen andN. H. Schmidt, in “Proceedings of Recrystallisation '90”, Wollongong, Australia, edited by T. Chandra (Min. Met. Mater. Soc., USA, 1990) in press.
S. I. Wright, J. W. Zhao andB. L. Adams,Tex. Micros.,13 (1991) 123.
D. Juul Jensen, N. Hansen, J. K. Kjems andT. Leffers, in “Proceedings of the 5th Riso Symposium”, edited by N. Hessel Andersen, M. Eldrup, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt, O. B. Pedersen and B. N. Singh (Riso National Laboratory Press, Roskilde, Denmark, 1984) p. 325.
D. Juul Jensen andV. Randle, in “Proceedings of the 10th Riso Symposium”, edited by J. Bilde-Sorensen, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt and O. B. Pedersen (Riso National Laboratory Press, 1989) p. 103.
S. Wismayer, B. Ralph andV. Randle, in “Proceedings of Recrystallisation '90”, Wollongong, Australia, edited by T. Chandra (Min. Met. Mater. Soc., USA, 1990) p. 181.
P. Van Houtte, private communication (1990).
“Proceedings of the Conference on Textures of Materials (ICOTOM9)”, September 1990, in press.
J. S. Kallend andG. Gottstein (eds) “Proceedings of ICOTOM8” (Metallurgical Society, 1987).
H. R. Wenk andU. F. Kocks,Met. Trans. 18A (1987) 1083.
F. C. Frank,ibid. 19A (1988) 403.
Idem, MRS Bull. March (1988) 24.
V. Randle, unpublished work (1989).
P. N. Quested, P. J. Henderson andM. McLean,Acta Metall. 36 (1988) 2743.
R. A. D. Mackenzie andD. J. Dingley, in “Proceedings of the Xth Congress on Electron Microscopy”, Kyoto, Japan (1986) p. 709.
R. Orsund andE. Nes,Scripta Metall. 23 (1989) 1187.
R. Orsund, J. Hjelen andE. Nes,ibid. 23 (1989) 1193.
H. J. Roven, E. A. Starke, O. Sodahl andJ. Hjelen,Scripta Metall. Mater. 24 (1990) 421.
J. Hjelen andE. Nes, in “Proceedings of ICOTOM8”, edited by J. S. Kallend and G. Gottstein (Met. Soc., 1988) p. 597.
A. Bottcher, M. Hastenrath, K. Lucke andJ. Hjelen, in “Proceedings of ICOTOM9”,Tex. Mic. 14–18 (1991) 673.
D. Juul Jensen, N. Hansen andY. L. Liu, in “Proceedings of the 10th Riso Symposium”, edited by J. B. Bilde-Sorensen, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt and O. B. Pedersen (Riso National Laboratory, Denmark, 1989) p. 409.
V. Randle, B. Ralph andD. J. Dingley,Acta Metall. 36 (1988) 267.
V. Randle andB. Ralph,Tex. Micros. 8/9 (1988) 531.
V. Randle andA. Brown,Phil. Mag. A58 (1988) 717.
Idem, ibid. A59 (1989) 1075.
V. Randle andB. Ralph,Proc. R. Soc. A415 (1988) 239.
Idem, Proc. Inst. Phys. Conf. Ser. 90 (1987) 205.
“Grain Boundary Structure and Kinetics” (ASM, Ohio, USA, 1980).
V. Randle andB. Ralph,J. Mater. Sci. 21 (1986) 3823.
L. Priester,Rev. Phys. Appl. 24 (1989) 419.
H. Mykura, “Grain Boundary Structure and Kinetics” (ASM, OH, 1980) p. 445.
V. Randle,Met. Trans. 21A (1990) 2215.
T. Watanabe,Phil. Mag. 47A (1983) 531.
M. Lunnon, PhD thesis, University of Bristol (1979).
M. L. Kronberg andF. H. Wilson,Met. Trans. 185 (1949) 501.
J. Furley andV. Randle,Mater. Sci. Technol. 7 (1991) 12.
V. Randle andB. Ralph, in “Proceedings of EMSA” (1988) p. 63.
Idem, in “Proceedings of the MRS Spring Meeting”, pp. 122, 419.
Idem, in “Proceedings of EUREM”, edited by P. J. Goodhew and H. G. Dickson, Inst. Phys. Conf. Ser no. 93 (1988) p. 231.
V. Randle, in “Proceedings of the 10th Riso Symposium”, edited by B. J. Bilde-Sorensen, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt and O. B. Pedersen (Riso National Laboratory, Denmark, 1989) p. 529.
S. R. Ortner andV. Randle,Scripta Metall. 23 (1989) 1903.
V. Randle andD. J. Dingley, in “Proceedings of Recrystallisation '90”, Wollongong, Australia, edited by T. Chandra (Min. Met. Mater. Soc., USA, 1990) p. 175.
V. Randle,Acta Metall. Mat. 39 (1991) 481.
Idem, Scripta Metall. 23 (1989) 773.
V. Randle andD. J. Dingley,ibid. 23 (1989) 1565.
Idem, in “Proceedings of Euromat '89”, Aachen, Germany, 1990, edited by H. E. Exner, V. Schumacher and D. G. M. Oberusel.
D. J. Dingley andK. Baba-Kishi, in “Proceedings of the XIth International Congress on Electron Microscopy”, Kyoto, 1986, p. 743.
K. Baba-Kishi andD. J. Dingley,ibid., p. 741.
Idem, Inst. Phys. Conf. Ser. 90 (EMAG 87) (1987) 135.
Idem, Institute of Metals Book 425, AEM workshop (1987) p. 71.
Idem, J. Appl. Crystallogr. 22 (1989) 89.
A. O. Kluken, O. Grong andJ. Hjelen,Met. Trans., submitted.
D. B. Jack, E. Koken andR. Underhill, in “Proceedings of the 10th Riso Symposium”, edited by B. J. Bilde-Sorensen, N. Hansen, D. Juul Jensen, T. Letters, H. Lilholt and O. B. Pedersen (Riso National Laboratory Press, Denmark, 1989) p. 403.
G. Laird II andV. Randle,Acta Met. Mat., submitted.
O. Rodrigues,J. de Math. Pure Appl. 5 (1840) 380.
K. H. G. Ashbee andJ. P. Sargent,Met. Trans. 21A (1990) 253.
P. Neumann, in “Proceedings of ICOTOM9”,Tex. Mic. 14–18 (1991) 53.
V. Randle,Proc. Roy. Soc. 431A (1990) 61.
J. K. Mackenzie,Acta Metall. 12 (1964) 223.
D. J. Dingley, A. Day andA. Bewick, in “Proceedings of ICOTOM9”,Tex. Mic. 14–18 (1991) 91.
D. J. Dingley,Inst. Phys. Conf. Ser. Vol.98 (1989) 473.
J. Hjelen, in Proceedings of Conference on Microscale Textures of Materials, to be published inTex. Mic.
R. Penelle,ibid.
T. Wang, P. R. Morris andB. L. Adams,Met. Trans. 21A (1990) 2265.
D. P. Field, B. L. Adams andJ. Zhao, in “Proceedings of ICOTOM9”, in press.
D. P. Field andB. L. Adams,Acta Met. Mat., in press.
B. L. Adams, J. Zhao andD. O'Hara,Acta Met. Mat.,38 (1990) 953.
‘Microscale Texture of Materials’, American Society for Metals meeting in Cincinnati, USA, 1991; to be published inTextures and Microstructures
V. Randle,Microtexture Determination and its Applications, Institute of Metals, London, in press.
V. Randle,Mat. Sci. Tech.,7 (1991) 985.
R. Penelle, T. Baudin, P. Paillard andL. Mora, Proc. ICOTOM9,Tex. and Mic. 14–18 (1991) 597.
H. S. Ubhi, C. J. Gilmore andA. W. Bowen, Proc. ‘EMAG '91’, Bristol, in press.
J. Hjelen, H. Weiland, J. Butler, J. Liu, H. Hu andE. Nes, Proc. ICOTOM9,Tex. and Mic. 14–18 (1991) 983.
D. Juul Jensen, N. Hansen andY. L. Liu,Mat. Sci. Tech. 7 (1991) 369.
C. T. Necker, R. D. Doherty andA. D. Rollett, Proc. ICOTOM9,Tex. and Mic. 14–18 (1991) 635.
A. J. Wilkinson,Mat. Sci. Eng. A135 (1991) 189.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Dingley, D.J., Randle, V. Microtexture determination by electron back-scatter diffraction. J Mater Sci 27, 4545–4566 (1992). https://doi.org/10.1007/BF01165988
Received:
Accepted:
Issue Date:
DOI: https://doi.org/10.1007/BF01165988