Abstract
The limit flow stresses for transverse loading of metal matrix composites reinforced with continuous fibers and for uniaxial loading of spherical particle-reinforced metal matrix composites are investigated by recently developed embedded cell models in conjunction with the finite element method. A fiber of circular cross section or a spherical particle is surrounded by a metal matrix, which is again embedded in the composite material with the mechanical behavior to be determined iteratively in a self-consistent manner. Good agreement has been obtained between experiment and calculation, and the embedded cell model is thus found to represent well metal matrix composites with randomly arranged inclusions.
Systematic studies of the mechanical behavior of fiber and particle-reinforced composites with plane strain and axisymmetric embedded cell models are carried out to determine the influence of fiber or particle volume fraction and matrix strain-hardening ability on composite strengthening levels. Results for random inclusion arrangements obtained with self-consistent embedded cell models are compared with strengthening levels for regular inclusion arrangements from conventional unit cell models.
Based on the self-consistent embedded cell models, a self-consistent matricity model has been developed to simulate the mechanical behavior of composites with two randomly distributed phases of interpenetrating microstructures. The model is an extension of the self-consistent model for matrices with randomly distributed inclusions. In addition to the volume fraction of the phases, the matricity model allows a further parameter of the microstructure, the matricity M of each phase, to be included into the simulation of the mechanical behavior of composites with interpenetrating microstructures. Good agreement has been obtained between experiment and calculation with respect to the composites’ mechanical behavior, and the matricity model is thus found to represent well metal matrix composites with interpenetrating microstructures. The matricity model can be applied to describe the mechanical behavior of arbitrary microstructures as observed in two-phase functionally graded materials, where the volume fraction as well as the matricity of the phases varies between the extreme values of 0 and 1.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Harrington WC Jr. Metal matrix composite applications. In: Ochiai S, editor. Mechanical properties of metallurgical composites. New York: Marcel Dekker; 1993.
Brockenbrough JR, Suresh S. Plastic deformation of continuous fiber reinforced MMCs: effects of fiber shape and distribution. Scripta Metall Mater. 1990;24:325.
Rammerstorfer FG, Fischer FD, Böhm HJ. Treatment of micro-mechanical phenomena by finite elements. In: Kuhn G, et al. editors. Discretization methods in structural mechanics. IUTAM/IACM Symposium, Vienna; 1989. Berlin/Heidelberg: Springer; 1990.
Evans AG. The mechanical properties of reinforced ceramic, metal and intermetallic matrix composites. Mater Sci Eng. 1991; A143:63.
Brockenbrough JR, Suresh S, Wienecke HA. Deformation of metal-matrix composites with continuous fibers: geometrical effects of fiber distribution and shape. Acta Metall Mater. 1991;39:735.
Dietrich C. Mechanisches Verhalten von Zweiphasengefügen: numerische und experimentelle Untersuchungen zum Einfluß der Gefügegeometrie. VDI-Fortschrittsberichte, Reihe 18, Nr. 128. Düsseldorf: VDI-Verlag; 1993.
Nakamura IT, Suresh S. Effects of thermal residual stresses and fiber packing on deformation of metal-matrix composites. Acta Metall Mater. 1993;41:1665.
Dietrich CM, Poech H, Schmauder S, Fischmeister HF. Numerische Modellierung des mechanischen Verhaltens von Faserverbundwerkstoffen unter transversaler Belastung. In: Leonhardt G, et al. editors. Verbundwerkstoffe und Werkstoffverbunde. DGM-lnformationsgesellschaft mbH. Oberursel; 1993.
Adams D. Inelastic analysis of a unidirectional composite subjected to transverse normal loading. J Compos Mater. 1970;4:310.
Jansson S. Homogenized nonlinear constitutive properties and local stress concentrations for composites with periodic internal structure. Int J Solids Struct. 1992;29:2181.
Zahl DB, Schmauder S, McMeeking RM. Transverse strength of metal matrix composites reinforced with strongly bonded continuous fibers in regular arrangements. Acta Metall Mater. 1994;42:2983.
Llorca J, Needleman A, Suresh S. An analysis of the effects of matrix void growth on deformation and ductility in metal-ceramic composites. Acta Metall Mater. 1991;39:2317.
Sautter M. Modellierung des Verformungsverhaltens mehrphasiger Werkstoffe mit der Methode der Finiten Elemente. PhD. Dissertation, University of Stuttgart; 1995.
Povirk GL, Stout MG, Bourke M, Goldstone JA, Lawson AC, Lovato M, Macewen SR, Nutt SR, Needleman A. Thermally and mechanically induced residual strains in Al-SiC composites. Acta Metall Mater. 1992;40:2391.
Böhm HJ, Rammerstorfer FG, Weissenbek E. Some simple models for micromechanical investigations of fiber arrangement effects in MMCs. Comput Mater Sci. 1993;1:177.
Böhm HJ, Rammerstorfer FG, Fischer FD, Siegmund T. Microscale arrangement effects on the thermomechanical behavior of advanced two-phase materials. ASME J Eng Mater Technol. 1994;116:268.
Bao G, Hutchinson JW, McMeeking RM. Particle reinforcement of ductile matrices against plastic flow and creep. Acta Metall Mater. 1991;39:1871.
Tvergaard V. Analysis of tensile properties for a whisker-reinforced metal-matrix composite. Acta Metall Mater. 1990;38:185.
Hom CL. Three-dimensional finite element analysis of plastic deformation in a whisker-reinforced metal matrix composite. J Mech Phys Solids. 1992;40:991.
Weissenbek E. Finite element modelling of discontinuously reinforced metal matrix composites. PhD. Dissertation. PhD. Dissertation, Technical University of Vienna; 1993.
Li Z, Schmauder S, Wanner A, Dong M. Transverse strength of metal matrix composites reinforced with strongly bonded continuous fibers in regular arrangements. Scripta Metall Mater. 1995;33:1289.
Christman T, Needleman A, Suresh Y. An experimental and numerical study of deformation in metal-ceramic composites. Acta Metall Mater. 1989;37:3029.
Suquet PM. Bounds and estimates for the overall properties of nonlinear composites. MECAMAT 93, Int. Seminar on Micromechanics of Materials. Paris: Editions Eyrolles; 1993;361:382.
Thebaud F. Vers l’introduction de l’endommagement dans la prévision globale du comportement de composites á matrice métallique. PhD. Dissertation, Université de Paris Sud; 1993.
Zahl DB, McMeeking RM. The influence of residual stress on the yielding of metal matrix composites. Acta Metall Mater. 1991;39:1171.
Poech MH. Deformation of two-phase materials: application of analytical elastic solutions to plasticity. Scripta Metall Mater. 1992;27:1027.
Farrissey L, Schmauder S, Dong M, Soppa E, Poech MH. Investigation of the strengthening of particulate reinforced composites using different analytical and finite element models. Comput Mater Sci. 1999;15:1.
Duva JM. A self-consistent analysis of the stiffening effect of rigid inclusions on a power-law material. Trans ASME Series H J Eng Mater Technol. 1984;106:317.
Sautter M, Dietrich C, Poech MH, Schmauder S, Fischmeister HF. Finite element modelling of a transverse-loaded fibre composite: effects of section size and net density. Comput Mater Sci. 1993;1:225.
Zahl DB, Schmauder S. Transverse strength of continuous fiber metal matrix composites. Comput Mater Sci. 1994;3:293.
Dong M, Schmauder S. Transverse mechanical behaviour of fiber reinforced composites – FE modeling with embedded cell models. Comput Mater Sci. 1996;5:53.
Järvstråt N. An ellipsoidal unit cell for the calculation of micro-stresses in short fibre composites. Comput Mater Sci. 1993;1:203.
Dong M, Schmauder S. Modeling of metal matrix composites by a self-consistent embedded cell model. Acta Mater. 1996;44:2465.
Poech MH, Ruhr D. Die quantitative Charakterisierung der Gefügeanordnung. Prakt Metallogr Sonderband. 1993;24:391.
Soppa E. Experimentelle Untersuchung des Verformungsverhaltens zweiphasiger Werkstoffe. Fortschr. Ber., VDI Reihe 5, 408. Düsseldorf: VDI-Verlag; 1995.
Lessle P, Dong M, Soppa E, Schmauder S. Selbstkonsistente Matrizitätsmodelle zur Simulation des mechanischen Verhaltens von Verbundwerkstoffen. In. Friedrich K, editor. Hrsg. DGM Informationsgesellschaft Verlag; 1997.
Schmauder S, Dong M, Lessle P. Verbundwerkstoffe mikromechanisch simuliert. Metall. 1997;51(7/8):404.
Schmauder S, Dong M, Lessle P. Simulation von Verbundwerkstoffen mit Teilchen und Fasern. Tagungsband XXIV. FEM Kongreß in Baden Baden, 17–18 Nov 1997.
Lessle P, Dong M, Soppa E, Schmauder S. Simulation of interpenetrating microstructures by self consistent matricity models. Scripta Mater. 1998;38:1327.
Schmauder S, Dong M, Lessle P. Self-consistent matricity model to simulate the mechanical behaviour of interpenetrating microstructures. Comput Mater Sci. 1999;15:455.
Willert-Porada M, Gerdes T, Rödiger K, Kolaska H. Einsatz von Mikrowellen zum Sintern pulvermetallurgischer Produkte. Metall. 1997;51(1/2):57.
Sautter M. Modellierung des Verformungsverhaltens mehrphasiger Werkstoffe mit der Methode der Finiten Elemente. Fortschritt Bericht. VDI Reihe 5, 398. Düsseldorf: VDI-Verlag; 1995.
Siegmund T, Werner E, Fischer FD. Structure–property relations in duplex materials. Comput Mater Sci. 1993;1:234.
Bao G, Hutchinson JW, McMeeking RM. The flow stress of dual-phase, non-hardening solids. Mech Mater. 1991;12:85.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Singapore Pte Ltd.
About this entry
Cite this entry
Dong, M., Schmauder, S. (2019). Application of Homogenization of Material Properties. In: Schmauder, S., Chen, CS., Chawla, K., Chawla, N., Chen, W., Kagawa, Y. (eds) Handbook of Mechanics of Materials. Springer, Singapore. https://doi.org/10.1007/978-981-10-6884-3_32
Download citation
DOI: https://doi.org/10.1007/978-981-10-6884-3_32
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-10-6883-6
Online ISBN: 978-981-10-6884-3
eBook Packages: EngineeringReference Module Computer Science and Engineering