Encyclopedia of Wildfires and Wildland-Urban Interface (WUI) Fires

Living Edition
| Editors: Samuel L. Manzello

Hot Metal Particles

  • Vytenis Babrauskas
Living reference work entry
DOI: https://doi.org/10.1007/978-3-319-51727-8_2-1

Synonyms

Sparks. The term “spark” can refer to either a non-sustained electrical discharge or a small, airborne, incandescent body. In the latter meaning, “hot metal particles” and “sparks” are synonyms.

Definitions

Hot metal particles considered in this section are small (a few millimeters or less) particles which are ejected from some process while heated to an incandescent state and can potentially act as ignition sources for a fuel.

Grinding sparks are hot metal particles created by a grinding operation.

Impact sparks are hot metal particles created due to a high-speed collision of two hard objects.

Introduction

A common cause for ignition of wildland fires are hot metal particles. These can come from numerous sources or activities (Babrauskas 2003; Mitchell 2009):
  • Railroads

  • Electric power lines (from conductor clashing, broken insulators, downed conductors, etc.)

  • Welding or torch-cutting metals

  • Grinding

  • Impact of power tools

Ignition of vegetation may be smoldering or flaming, but...

This is a preview of subscription content, log in to check access.

References

  1. Anon (2013) Standard for fire prevention during welding, cutting, and other hot work (NFPA 51B). NFPA, QuincyGoogle Scholar
  2. Babrauskas V (2003) Ignition handbook. Fire Science Publishers/Soc Fire Prot Eng, IssaquahGoogle Scholar
  3. Babrauskas V (2005) Risk of ignition of forest fires from black powder or muzzle-loading firearms. Report for US Forest Service, San Dimas T&D CenterGoogle Scholar
  4. Babrauskas V (2018) Engineering guidance for smoldering fires. J Fire Invest Res Eng, to be publishedGoogle Scholar
  5. Chen JH et al (1989) A study of the mechanism for globular metal transfer from covered electrodes. Weld J 65(4):145-s–150-sGoogle Scholar
  6. Farrall GA, Hudda FG, Toney JG (1983) The time-resolved characterization of erosion products from high-current, copper vacuum arcs. IEEE Trans Plasma Sci 11:132–138CrossRefGoogle Scholar
  7. Finney MA et al (2016) A study of wildfire ignition by rifle bullets. Fire Tech 52:933–954CrossRefGoogle Scholar
  8. Frank-Kamenetskii DA (1969) Diffusion and heat transfer in chemical kinetics, 2nd edn. Plenum Press, New YorkGoogle Scholar
  9. Gilbert/Commonwealth (1979) Transmission line reference book. Wind-induced conductor motion. Based on EPRI research project 792, EPRI, Menlo ParkGoogle Scholar
  10. Gol’dshleger UI et al (1973) Ignition of a condensed explosive by a hot object of finite dimensions. Combust Explosion Shock Waves 9:99–102CrossRefGoogle Scholar
  11. Hadden RM (2011) Ignition of combustible fuel beds by hot particles: an experimental and theoretical study. Fire Tech 47:341–355CrossRefGoogle Scholar
  12. Hagimoto Y et al (1998) Scattering and ignite ng properties of sparks generated in an arc welding. 6th Indo Pacific Congress on Legal Medicine and Forensic Sciences (INPALMS), Yoyodo, pp 863–866Google Scholar
  13. Hagimoto Y et al (2007) A short-circuit as an ignition source. Interflam 2007:1555–1560Google Scholar
  14. Hagiwara T et al (1982) Ignition risk to combustibles by welding spatter (in Japanese). J Jpn Assn Fire Sci Engrg 32(5):8–12Google Scholar
  15. Hölemann H, Worpenberg R (1987) Untersuchungen zur Entstehung von Bränden durch Schweißen, Schneiden und verwandte Verfahren – Temperatur, Geschwindigkeit, GrÖße und Wärmeinhalt von Brennschneidschlacketeilchen, Schweißen und Schneiden 39(7):315–321Google Scholar
  16. Hölemann H, Worpenberg R (1992) Brandursache Schweißen, Brennschneiden und Löten – Zündmechanismen glühender Partikel. VFDB Z 41:79–89Google Scholar
  17. Howitt DG (2015) An assessment of hot metal fragments from heavy mechanical equipment as a potential ignition source for forest litter. J Fire Sci 33:427–444CrossRefGoogle Scholar
  18. Jones JC (1995) Improved calculations concerning the ignition of forest litter by hot particle ingress. J Fire Sci 13:350–356CrossRefGoogle Scholar
  19. Kim YS, Eagar TW (1993) Analysis of metal transfer in gas metal arc welding. Weld J 72(6):269-s–276-sGoogle Scholar
  20. Lewis K (2017) Hot particle ignition from arcing as a wildland fire cause. 2017 Wildland Fire Litigation Conf, San DiegoGoogle Scholar
  21. Libershal B (1989) Target shooting, automatic rifles and steel core bullets. Wildfire Strikes Home 3(1):8–9Google Scholar
  22. Liñán A, Kindelán M (1981) Ignition of a reactive solid by an inert hot spot. In: Progress in astronautics and aeronautics, vol 76. AIAA, New York, pp 412–426Google Scholar
  23. Look A D (1948) Underground metal-mine fires from cutting and welding (IC 7453). Bureau of MinesGoogle Scholar
  24. Messler RW Jr (1999) Principles of welding. Wiley-VCH, WeinheimCrossRefGoogle Scholar
  25. Mikkelsen K (2014) An experimental investigation of ignition propensity of hot work processes in the nuclear industry (M.S. thesis), Univ Waterloo, CanadaGoogle Scholar
  26. Mills AF, Hang X (1984) Trajectories of sparks from arcing aluminum power cables. Fire Tech 20:5–14CrossRefGoogle Scholar
  27. Mitchell J W (2009) Power lines and catastrophic wildland fire in southern California. Proc 11th Fire & Mater ConfGoogle Scholar
  28. Okegawa S et al (1996) Measurement of distance and ignition tests to gases by welding spatter (in Japanese). J Jpn Soc Saf Engrg 5(2):112–119Google Scholar
  29. Rallis CJ, Mangaya BM (2002) Ignition of veld grass by hot aluminium particles ejected from clashing overhead transmission lines. Fire Tech 38:81–92CrossRefGoogle Scholar
  30. Rogers RL et al (2006) Ignition of dust clouds and dust deposits by friction sparks and hotspots. Hazards XIX, paper 24, IChemEGoogle Scholar
  31. Rowntree GWG, Stokes AD (1994) Fire ignition by aluminium particles of controlled size. J Electr Electron Eng Aust 14:117–123Google Scholar
  32. Schōnherr W (1982) Fire risks with welding torches and manual arc welding – globules, spatter and how far they can be thrown. Schweiss Schneid 34(4):E74–E77Google Scholar
  33. Stokes AD (1990) Fire ignition by copper particles of controlled size. J Electr Electron Eng Aust 10:188–194Google Scholar
  34. Stokes AD (2001) Fire ignition by electrically produced incandescent particles. Dept Elec Eng, Univ Sydney, AustraliaGoogle Scholar
  35. Tanaka K et al (1997) Research on the locus and the velocity of spatter in shielded metal arc welding (in Japanese). Q J Jpn Weld Soc 15(2):247–253CrossRefGoogle Scholar
  36. Tanaka T (1977) On the inflammability of combustible materials by welding spatter (in Japanese). Rep Natl Res Inst Police Sci 30(1):51–58Google Scholar
  37. Tse SD, Fernandez-Pello AC (1998) On the flight paths of metal particles and embers generated by power lines in high winds – potential source of wildland fires. Fire Saf J 30:333–356CrossRefGoogle Scholar
  38. van Wingerden K et al (2011) Ignition of dust layers by mechanical sparks. Loss Prev Symp, AIChEGoogle Scholar
  39. Way PT (2017) Vegetation management and powerlines, 2017 Wildland fire litigation conf, San DiegoGoogle Scholar
  40. Zak CD (2015) The effect of particle properties on hot particle spot fire ignition (Ph.D. diss), Univ Calif BerkeleyGoogle Scholar

Copyright information

© Springer International Publishing AG 2018

Authors and Affiliations

  1. 1.Fire Science and Technology Inc., and Department of Mechanical and Aerospace EngineeringUniversity of CaliforniaSan DiegoUSA

Section editors and affiliations

  • Sayaka Suzuki
    • 1
  1. 1.National Research Institute of Fire and Disaster (NRIFD)TokyoJapan