Advertisement

Electrochemical Techniques, Impedance, and Spectroscopy

  • Shengxi Li
  • Qixin Zhou
  • Hongbo Cong
Living reference work entry

Abstract

Electrochemical impedance spectroscopy (EIS) is a powerful technique for characterizing a wide range of electrochemical systems. It is based on the application of a small amplitude, alternating current signal to the systems, and therefore is considered a non-destructive technique. This chapter begins with a brief introduction of the fundamentals of EIS, then focuses on instrumentation characteristics, especially the various electrode configurations, and finally discusses the wide applications of EIS in corrosion studies. The applications of EIS in the following corrosion topics are reviewed: atmospheric corrosion, corrosion in concrete, coatings and films, inhibitors, high-temperature corrosion, oil and gas industry-related corrosion, microbiologically influenced corrosion, and stress corrosion cracking. For each application, besides the review of the capability of EIS, typical equivalent circuit models are also highlighted. In some applications, the limitations of EIS measurements are also pointed out.

References

  1. Allahar KN, Su Q, Bierwagen GP, Lee D (2008) Monitoring of the AC-DC-AC degradation of organic coatings using embedded electrodes. Corrosion 64:773–787CrossRefGoogle Scholar
  2. Allahar K, Su Q, Bierwagen G (2010) Non-substrate EIS monitoring of organic coatings with embedded electrodes. Prog Org Coat 67:180–187CrossRefGoogle Scholar
  3. Amand S, Musiani M, Orazem ME et al (2013) Constant-phase-element behavior caused by inhomogeneous water uptake in anti-corrosion coatings. Electrochim Acta 87:693–700CrossRefGoogle Scholar
  4. Armstrong RD, Jenkins ATA, Johnson BW (1995) An investigation into the UV breakdown of thermoset polyester coatings using impedance spectroscopy. Corros Sci 37:1615–1625CrossRefGoogle Scholar
  5. Asakura Y, Karasawa H, Sakagami M, Uchida S (1989) Relationships between corrosion behavior of AISI 304 stainless steel in high-temperature pure water and its oxide film structures. Corrosion 45:119–124CrossRefGoogle Scholar
  6. Aung NN, Liu X (2012) High temperature electrochemical sensor for in situ monitoring of hot corrosion. Corros Sci 65:1–4CrossRefGoogle Scholar
  7. Aung NN, Liu X (2013) Effect of SO2 in flue gas on coal ash hot corrosion of Inconel 740 alloy – a high temperature electrochemical sensor study. Corros Sci 76:390–402CrossRefGoogle Scholar
  8. Aung NN, Liu X (2014) Effect of temperature on coal ash hot corrosion resistance of Inconel 740 superalloy. Corros Sci 82:227–238CrossRefGoogle Scholar
  9. Beaunier L, Epelboin I, Lestrade JC, Takenouti H (1976) Etude electrochimique, et par microscopie electronique a balayage, du fer recouvert de peinture. Surf Technol 4:237–254CrossRefGoogle Scholar
  10. Bellucci F, Nicodemo L (1993) Water transport in organic coatings. Corrosion 49:235–247CrossRefGoogle Scholar
  11. Betova I, Bojinov M, Kinnunen P et al (2006) Composition, structure, and properties of corrosion layers on ferritic and austenitic steels in ultrasupercritical water. J Electrochem Soc 153:B464–B473CrossRefGoogle Scholar
  12. Betova I, Bojinov M, Kinnunen P et al (2007) Surface film electrochemistry of austenitic stainless steel and its main constituents in supercritical water. J Supercrit Fluids 43:333–340CrossRefGoogle Scholar
  13. Betova I, Bojinov M, Karastoyanov V et al (2012) Effect of water chemistry on the oxide film on alloy 690 during simulated hot functional testing of a pressurised water reactor. Corros Sci 58:20–32CrossRefGoogle Scholar
  14. Bian C, Wang ZM, Han X et al (2015) Electrochemical response of mild steel in ferrous ion enriched and CO2 saturated solutions. Corros Sci 96:42–51CrossRefGoogle Scholar
  15. Bierwagen GP, He L, Li J et al (2000) Studies of a new accelerated evaluation method for coating corrosion resistance – thermal cycling testing. Prog Org Coat 39:67–78CrossRefGoogle Scholar
  16. Bierwagen GP, Wang X, Tallman DE (2003) In situ study of coatings using embedded electrodes for ENM measurements. Prog Org Coat 46:163–175CrossRefGoogle Scholar
  17. Bojinov M, Karastoyanov V, Kinnunen P, Saario T (2010) Influence of water chemistry on the corrosion mechanism of a zirconium-niobium alloy in simulated light water reactor coolant conditions. Corros Sci 52:54–67CrossRefGoogle Scholar
  18. Bojinov M, Nowak E, Saario T et al (2014) Effect of chloride on the oxides on low-alloyed steel in conditions of a light water reactor pressure vessel cladding flaw. J Electrochem Soc 161:C177–C187CrossRefGoogle Scholar
  19. Bonora PL, Deflorian F, Fedrizzi L (1996) Electrochemical impedance spectroscopy as a tool for investigating underpaint corrosion. Electrochim Acta 41:1073–1082CrossRefGoogle Scholar
  20. Bosch RW (2005) Electrochemical impedance spectroscopy for the detection of stress corrosion cracks in aqueous corrosion systems at ambient and high temperature. Corros Sci 47:125–143CrossRefGoogle Scholar
  21. Bosch RW, Moons F, Zheng JH, Bogaerts WF (2001) Application of electrochemical impedance spectroscopy for monitoring stress corrosion cracking. Corrosion 57:532–539CrossRefGoogle Scholar
  22. Brasher DM, Kingsbury AH (1954) Electrical measurements in the study of immersed paint coatings on metal. I. Comparison between capacitance and gravimetric methods of estimating water-uptake. J Appl Chem 4:62–72CrossRefGoogle Scholar
  23. Bretherton N, Thompson GE, Turgoose S (1993) An electrochemical investigation of the development of phosphate conversion coatings. Corros Sci 35:1297–1303CrossRefGoogle Scholar
  24. Carpintero-Moreno EJ, Gonzalez-Rodriguez JG, Uruchurtu-Chavarín J et al (2013) Detection of stress corrosion cracking in a dual-phase steel using electrochemical noise and impedance spectroscopy. Corrosion 69:85–94CrossRefGoogle Scholar
  25. Castela AS, Simões AM (2003a) Water sorption in freestanding PVC films by capacitance measurements. Prog Org Coat 46:130–134CrossRefGoogle Scholar
  26. Castela AS, Simões AM (2003b) An impedance model for the estimation of water absorption in organic coatings. Part II: a complex equation of mixture. Corros Sci 45:1647–1660CrossRefGoogle Scholar
  27. Castela AS, Simões AM (2003c) An impedance model for the estimation of water absorption in organic coatings. Part I: a linear dielectric mixture equation. Corros Sci 45:1631–1646CrossRefGoogle Scholar
  28. Castela ASL, Simões AM, Ferreira MGS (2000) E.I.S. Evaluation of attached and free polymer films. Prog Mater Sci 38:1–7Google Scholar
  29. Cheng Q, Song S, Song L, Hou B (2013) Effect of relative humidity on the initial atmospheric corrosion behavior of zinc during drying. J Electrochem Soc 160:C380–C389CrossRefGoogle Scholar
  30. Choi Y-S, Kim J-G (2005) A galvanic sensor for monitoring the corrosion damage of buried pipelines: part 1 – electrochemical tests to determine the correlation of probe current to actual corrosion damage in synthetic groundwater. Corrosion 61:293–301CrossRefGoogle Scholar
  31. Choi Y-S, Kim J-G, Yang SJ (2006) A galvanic sensor for monitoring the corrosion damage of buried pipelines: part 2 – correlation of sensor output to actual corrosion damage of pipeline in soil and tap water environments. Corrosion 62:522–532CrossRefGoogle Scholar
  32. Choi Y-S, Kim J-G, Koo J-Y (2007) A galvanic sensor for monitoring the corrosion damage of buried pipelines: part 3 – correlation of probe current to cathodic protection and stray current. Corrosion 63:951–957CrossRefGoogle Scholar
  33. Christensen BJ, Coverdale RT, Olson RA et al (1994) Impedance spectroscopy of hydrating cement-based materials: measurement, interpretation, and application. J Am Ceramic Soc 77:2789–2804CrossRefGoogle Scholar
  34. Cooper K, Smith M, Budiansky N, Scully J (2006) Development of a multi-electrode array impedance analyzer for corrosion science and sensors. CORROSION/2006 Conference, NACE International, Paper no. 00674Google Scholar
  35. Davis GD, Rich MJ, Drzal LT (2004) Monitoring moisture uptake and delamination in CFPR reinforced concrete structures with electrochemical impedance sensors. J Nondestruct Eval 23:1–9CrossRefGoogle Scholar
  36. de Levie R (1963) On porous electrodes in electrolyte solutions. Electrochim Acta 8:751–780CrossRefGoogle Scholar
  37. Deflorian F, Fedrizzi L, Bonora PL (1996) Influence of the photo-oxidative degradation on the water barrier and corrosion protection properties of polyester paints. Corros Sci 38:1697–1708CrossRefGoogle Scholar
  38. Deflorian F, Fedrizzi L, Rossi S, Bonora PL (1999) Organic coating capacitance measurement by EIS: ideal and actual trends. Electrochim Acta 44:4243–4249CrossRefGoogle Scholar
  39. Dhouibi L, Triki E, Raharinaivo A (2002) The application of electrochemical impedance spectroscopy to determine the long-term effectiveness of corrosion inhibitors for steel in concrete. Cem Concr Compos 24:35–43CrossRefGoogle Scholar
  40. Döner A, Şahin EA, Kardaş G, Serindaĝ O (2013) Investigation of corrosion inhibition effect of 3-[(2-hydroxy-benzylidene)-amino]-2-thioxo-thiazolidin-4-one on corrosion of mild steel in the acidic medium. Corros Sci 66:278–284CrossRefGoogle Scholar
  41. Dowling NJE, Guezennec J, Lemoine ML et al (1988) Analysis of carbon steels affected by bacteria using electrochemical impedance and direct current techniques. Corrosion 44:869–874CrossRefGoogle Scholar
  42. Durand-keklikian L, Cragnolino G, Macdonald DD (1991) Technical note: in situ A.C. Impedance studies of oxide film growth on zircaloy-4 in high temperature/high pressure steam. Corros Sci 32:361–365CrossRefGoogle Scholar
  43. El-Mahdy GA, Kim KB (2004) AC impedance study on the atmospheric corrosion of aluminum under periodic wet-dry conditions. Electrochim Acta 49:1937–1948CrossRefGoogle Scholar
  44. El-Mahdy GA, Nishikata A, Tsuru T (2000a) AC impedance study on corrosion of 55%Al-Zn alloy-coated steel under thin electrolyte layers. Corros Sci 42:1509–1521CrossRefGoogle Scholar
  45. El-Mahdy GA, Nishikata A, Tsuru T (2000b) Electrochemical corrosion monitoring of galvanized steel under cyclic wet-dry conditions. Corros Sci 42:183–194CrossRefGoogle Scholar
  46. Faidi SE, Scantlebury JD, Bullivant P et al (1993) An electrochemical study of zinc-containing epoxy coatings on mild steel. Corros Sci 35:1319–1328CrossRefGoogle Scholar
  47. Feliu V, González JA, Andrade C, Feliu S (1998a) Equivalent circuit for modelling the steel-concrete interface. I. Experimental evidence and theoretical predictions. Corros Sci 40:975–993CrossRefGoogle Scholar
  48. Feliu V, González JA, Andrade C, Feliu S (1998b) Equivalent circuit for modelling the steel-concrete interface. II. Complications in applying the Stern-Geary equation to corrosion rate determinations. Corros Sci 40:995–1006CrossRefGoogle Scholar
  49. Feng X, Lu X, Zuo Y et al (2016) Electrochemical study the corrosion behaviour of carbon steel in mortars under compressive and tensile stresses. Corros Sci 103:66–74CrossRefGoogle Scholar
  50. Foyet A, Wu TH, Kodentsov A et al (2013) Corrosion protection and delamination mechanism of epoxy/carbon black nanocomposite coating on AA2024-T3. J Electrochem Soc 160:C159–C167CrossRefGoogle Scholar
  51. Frangini S, Loreti S (2006) The role of temperature on the corrosion and passivation of type 310S stainless steel in eutectic (Li + K) carbonate melt. J Power Sources 160:800–804CrossRefGoogle Scholar
  52. Fu X, Dong J, Han E, Ke W (2009) A new experimental method for in situ corrosion monitoring under alternate wet-dry conditions. Sensors 9:10400–10410CrossRefGoogle Scholar
  53. Fulger M, Ohai D, Mihalache M et al (2009) Oxidation behavior of Incoloy 800 under simulated supercritical water conditions. J Nucl Mater 385:288–293CrossRefGoogle Scholar
  54. Fulger M, Mihalache M, Ohai D et al (2011) Analyses of oxide films grown on AISI 304L stainless steel and Incoloy 800HT exposed to supercritical water environment. J Nucl Mater 415:147–157CrossRefGoogle Scholar
  55. Gao G, Stott FH, Dawson JL, Farreil DM (1990) Electrochemical monitoring of high-temperature molten-salt corrosion. Oxid Met 33:79–94CrossRefGoogle Scholar
  56. Gao H, Li Q, Dai Y et al (2010) High efficiency corrosion inhibitor 8-hydroxyquinoline and its synergistic effect with sodium dodecylbenzenesulphonate on AZ91D magnesium alloy. Corros Sci 52:1603–1609CrossRefGoogle Scholar
  57. Gonçalves RS, Azambuja DS, Serpa Lucho AM (2002) Electrochemical studies of propargyl alcohol as corrosion inhibitor for nickel, copper, and copper/nickel (55/45) alloy. Corros Sci 44:467–479CrossRefGoogle Scholar
  58. Gu P, Fu Y, Xie P, Beaudoin JJ (1994) Characterization of surface corrosion of reinforcing steel in cement paste by low frequency impedance spectroscopy. Cem Concr Res 24:231–242CrossRefGoogle Scholar
  59. Gui F, Kelly RG (2005) Performance assessment and prediction of corrosion prevention compounds with electrochemical impedance spectroscopy. Corros Sci 61:119–129CrossRefGoogle Scholar
  60. Gusmano G, Labella P, Montesperelli G et al (2006) Study of the inhibition mechanism of imidazolines by electrochemical impedance spectroscopy. Corrosion 62:576–583CrossRefGoogle Scholar
  61. Hamlaoui Y, Pedraza F, Tifouti L (2008) Corrosion monitoring of galvanised coatings through electrochemical impedance spectroscopy. Corros Sci 50:1558–1566CrossRefGoogle Scholar
  62. Hernández M, Genescá J, Uruchurtu J, Barba A (2009) Correlation between electrochemical impedance and noise measurements of waterborne coatings. Corros Sci 51:499–510CrossRefGoogle Scholar
  63. Hinderliter BR, Allahar KN, Bierwagen GP et al (2008) Water sorption and diffusional properties of a cured epoxy resin measured using alternating ionic liquids/aqueous electrolytes in electrochemical impedance spectroscopy. J Coat Technol Res 5:431–438CrossRefGoogle Scholar
  64. Hirayama R, Hanuyama S (1991) Electrochemical impedance for degraded coated steel having pores. Corrosion 47:952–958CrossRefGoogle Scholar
  65. Hirschorn B, Orazem ME, Tribollet B et al (2010) Determination of effective capacitance and film thickness from constant-phase-element parameters. Electrochim Acta 55:6218–6227CrossRefGoogle Scholar
  66. Hong S, Harichandran RS (2005) Nondestructive evaluation of CFRP/concrete bond in beams using electrochemical impedance spectroscopy. J Compos Constr 9:515–523CrossRefGoogle Scholar
  67. Hu JM, Zhang JQ, Cao CN (2003) Determination of water uptake and diffusion of Cl-ion in epoxy primer on aluminum alloys in NaCl solution by electrochemical impedance spectroscopy. Prog Org Coat 46:273–279CrossRefGoogle Scholar
  68. Huang H, Dong Z, Chen Z, Guo X (2011) The effects of Cl-ion concentration and relative humidity on atmospheric corrosion behaviour of PCB-Cu under adsorbed thin electrolyte layer. Corros Sci 53:1230–1236CrossRefGoogle Scholar
  69. Jegdić BV, Bajat JB, Popić JP et al (2011) The EIS investigation of powder polyester coatings on phosphated low carbon steel: the effect of NaNO2 in the phosphating bath. Corros Sci 53:2872–2880CrossRefGoogle Scholar
  70. Ji WG, Hu JM, Zhang JQ, Cao CN (2006) Reducing the water absorption in epoxy coatings by silane monomer incorporation. Corros Sci 48:3731–3739CrossRefGoogle Scholar
  71. John DG, Searson PC, Dawson JL (1981) Use of AC impedance technique in studies on steel in concrete in immersed conditions. Br Corros J 16:102–106CrossRefGoogle Scholar
  72. Jorcin JB, Aragon E, Merlatti C, Pébère N (2006) Delaminated areas beneath organic coating: a local electrochemical impedance approach. Corros Sci 48:1779–1790CrossRefGoogle Scholar
  73. Khaled KF, Amin MA (2009) Corrosion monitoring of mild steel in sulphuric acid solutions in presence of some thiazole derivatives – molecular dynamics, chemical and electrochemical studies. Corros Sci 51:1964–1975CrossRefGoogle Scholar
  74. Kim Y-J (2000) In-situ electrochemical impedance measurement of oxide film formed on type 304 stainless steel in high-temperature water. Corrosion 56:389–394CrossRefGoogle Scholar
  75. Kinsella B, Tan YJ, Bailey S (1998) Electrochemical impedance spectroscopy and surface characterization techniques to study carbon dioxide corrosion product scales. Corrosion 54:835–842CrossRefGoogle Scholar
  76. Kittel J, Celati N, Keddam M, Takenouti H (2001) New methods for the study of organic coatings by EIS: new insights into attached and free films. Prog Org Coat 41:93–98CrossRefGoogle Scholar
  77. Kittel J, Celati N, Keddam M, Takenouti H (2003) Influence of the coating-substrate interactions on the corrosion protection: characterisation by impedance spectroscopy of the inner and outer parts of a coating. Prog Org Coat 46:135–147CrossRefGoogle Scholar
  78. Koleva DA, de Wit JHW, van Breugel K et al (2007) Investigation of corrosion and cathodic protection in reinforced concrete I. Application of electrochemical techniques. J Electrochem Soc 154:P52–P61CrossRefGoogle Scholar
  79. Lay P, Lawrence PF, Wilkins JM, Williams DE (1985) An A.C. Impedance study of steel in concrete. J Appl Electrochem 15:755–766CrossRefGoogle Scholar
  80. Li C, Ma Y, Li Y, Wang F (2010) EIS monitoring study of atmospheric corrosion under variable relative humidity. Corros Sci 52:3677–3686CrossRefGoogle Scholar
  81. Li X, Deng S, Fu H (2011) Benzyltrimethylammonium iodide as a corrosion inhibitor for steel in phosphoric acid produced by dihydrate wet method process. Corros Sci 53:664–670CrossRefGoogle Scholar
  82. Lindqvist SA (1985) Theory of dielectric properties of heterogeneous substances applied to water in a paint film. Corrosion 41:69–75CrossRefGoogle Scholar
  83. Liu H, Gu T, Zhang G et al (2016) The effect of magneticfield on biomineralization and corrosion behavior of carbon steel induced by iron-oxidizing bacteria. Corros Sci 102:93–102CrossRefGoogle Scholar
  84. Lokesh KS, De Keersmaecker M, Elia A et al (2012) Adsorption of cobalt (II) 5,10,15,20-tetrakis(2-aminophenyl)-porphyrin onto copper substrates: characterization and impedance studies for corrosion inhibition. Corros Sci 62:73–82CrossRefGoogle Scholar
  85. Ma X, Cheng Q, Zheng M et al (2015) Monitoring marine atmospheric corrosion by electrochemical impedance spectroscopy under various relative humidities. Int J Electrochem Sci 10:10402–10421Google Scholar
  86. Macák J, Sajdl P, Kučera P et al (2006) In situ electrochemical impedance and noise measurements of corroding stainless steel in high temperature water. Electrochim Acta 51:3566–3577CrossRefGoogle Scholar
  87. Macdonald JR (1987) Impedance spectroscopy. Wiley, New YorkGoogle Scholar
  88. MacDonald DD, McKubre MCH, Urquidi-MacDonald M (1988) Theoretical assessment of AC impedance spectroscopy for detecting corrosion of rebar in reinforced concrete. Corrosion 44:2–7CrossRefGoogle Scholar
  89. Macedo MCSS, Margarit-Mattos ICP, Fragata FL et al (2009) Contribution to a better understanding of different behaviour patterns observed with organic coatings evaluated by electrochemical impedance spectroscopy. Corros Sci 51:1322–1327CrossRefGoogle Scholar
  90. Mansfeld F (1988) Evaluation of anodized aluminum surfaces with electrochemical impedance spectroscopy. J Electrochem Soc 135:828–833CrossRefGoogle Scholar
  91. Mansfeld F (1995) Use of electrochemical impedance spectroscopy for the study of corrosion protection by polymer coatings. J Appl Electrochem 25:187–202Google Scholar
  92. Mansfeld F, Little B (1991) A technical review of electrochemical techniques applied to microbiologically influenced corrosion. Corros Sci 32:247–272CrossRefGoogle Scholar
  93. Mansfeld F, Tsai CH (1991) Determination of coating deterioration with EIS. I. Basic relationships. Corrosion 47:958–963CrossRefGoogle Scholar
  94. Markhali BP, Naderi R, Mahdavian M et al (2013) Electrochemical impedance spectroscopy and electrochemical noise measurements as tools to evaluate corrosion inhibition of azole compounds on stainless steel in acidic media. Corros Sci 75:269–279CrossRefGoogle Scholar
  95. Martin FJ, Cheek GT, O’Grady WE, Natishan PM (2005) Impedance studies of the passive film on aluminium. Corros Sci 47:3187–3201CrossRefGoogle Scholar
  96. McCarter WJ (1996) The A.C. Impedance response of concrete during early hydration. J Mater Sci 31:6285–6292CrossRefGoogle Scholar
  97. Mendonça GLF, Costa SN, Freire VN et al (2017) Understanding the corrosion inhibition of carbon steel and copper in sulphuric acid medium by amino acids using electrochemical techniques allied to molecular modelling methods. Corros Sci 115:41–55CrossRefGoogle Scholar
  98. Mierisch AM, Taylor SR, Celli V (2003) Understanding the degradation of organic coatings through local electrochemical impedance methods. J Electrochem Soc 150:B309–B315CrossRefGoogle Scholar
  99. Miskovic-Stankovic VB, Dražić DM, Kačarević-Popović Z (1996) The sorption characteristics of epoxy coatings electrodeposited on steel during exposure to different corrosive agents. Corros Sci 38:1513–1523CrossRefGoogle Scholar
  100. Miszczyk A, Schauer T (2005) Electrochemical approach to evaluate the interlayer adhesion of organic coatings. Prog Org Coat 52:298–305CrossRefGoogle Scholar
  101. Mohammadi F, Nickchi T, Attar MM, Alfantazi A (2011) EIS study of potentiostatically formed passive film on 304 stainless steel. Electrochim Acta 56:8727–8733CrossRefGoogle Scholar
  102. Montemor MF, Simoes AMP, Salta MM, Ferreira MGS (1993) The assessment of the electrochemical behaviour of flyash-containing concrete by impedance spectroscopy. Corros Sci 35:1571–1578CrossRefGoogle Scholar
  103. Murray JN, Hack HP (1991) Long-term testing of epoxy-coated steel in ASTM seawater using electrochemical impedance spectroscopy. Corrosion 47:480–489CrossRefGoogle Scholar
  104. Murray JN, Hack HP (1992) Testing organic architectural coatings in ASTM synthetic seawater immersion conditions using EIS. Corrosion 48:671–685CrossRefGoogle Scholar
  105. Murray JN, Moran PJ (1989) Influence of moisture on corrosion of pipeline steel in soils using in situ impedance spectroscopy. Corrosion 45:34–43CrossRefGoogle Scholar
  106. Nguyen VN, Perrin FX, Vernet JL (2005) Water permeability of organic/inorganic hybrid coatings prepared by sol-gel method: a comparison between gravimetric and capacitance measurements and evaluation of non-Fickian sorption models. Corros Sci 47:397–412CrossRefGoogle Scholar
  107. Ni CS, Lu LY, Zeng CL, Niu Y (2011) Electrochemical impedance studies of the initial-stage corrosion of 310S stainless steel beneath thin film of molten (0.62Li,0.38K)2CO3 at 650 °C. Corros Sci 53:1018–1024CrossRefGoogle Scholar
  108. Nishikata A, Ichihara Y, Tsuru T (1995a) An application of electrochemical impedance spectroscopy to atmospheric corrosion study. Corros Sci 37:897–911CrossRefGoogle Scholar
  109. Nishikata A, Yamashita Y, Isatayama H et al (1995b) An electrochemical impedance study on atmospheric corrosion of steels in a cyclic wet-dry condition. Corros Sci 37:2059–2069CrossRefGoogle Scholar
  110. Nishikata A, Ichihara Y, Hayashi V, Tsuru T (1997) Influence of electrolyte layer thickness and pH on the initial stage of the atmospheric corrosion of iron. J Electrochem Soc 144:1244–1252CrossRefGoogle Scholar
  111. Nishikata A, Suzuki F, Tsuru T (2005) Corrosion monitoring of nickel-containing steels in marine atmospheric environment. Corros Sci 47:2578–2588CrossRefGoogle Scholar
  112. Nishikata A, Zhu Q, Tada E (2014) Long-term monitoring of atmospheric corrosion at weathering steel bridges by an electrochemical impedance method. Corros Sci 87:80–88CrossRefGoogle Scholar
  113. Oltra R, Keddamt M (1988) Application of impedance technique to localized corrosion. Corros Sci 28:1–18CrossRefGoogle Scholar
  114. Oskuie AA, Shahrabi T, Shahriari A, Saebnoori E (2012) Electrochemical impedance spectroscopy analysis of X70 pipeline steel stress corrosion cracking in high pH carbonate solution. Corros Sci 61:111–122CrossRefGoogle Scholar
  115. Pan TJ, Lu WM, Ren YJ et al (2009) Electrochemical-impedance-spectroscopy (EIS) study of corrosion of steels 12CrMoV and SS304 beneath a molten ZnCl2-KCl film at 400 °C in air. Oxid Met 72:179–190CrossRefGoogle Scholar
  116. Park JR, Macdonald DD (1983) Impedance studies of the growth of porous magnetite films on carbon steel in high temperature aqueous systems. Corros Sci 23:295–315CrossRefGoogle Scholar
  117. Perez C, Collazo A, Izquierdo M et al (1999) Characterisation of the barrier properties of different paint systems. Part I. Experimental set-up and ideal Fickian diffusion. Prog Org Coat 36:102–108CrossRefGoogle Scholar
  118. Petit MC, Cid M, Puiggali M, Amor Z (1990) An impedance study of the passivity breakdown during stress corrosion cracking phenomena. Corros Sci 31:491–496CrossRefGoogle Scholar
  119. Philippe LVS, Lyon SB, Sammon C, Yarwood J (2008) Validation of electrochemical impedance measurements for water sorption into epoxy coatings using gravimetry and infra-red spectroscopy. Corros Sci 50:887–896CrossRefGoogle Scholar
  120. Popov BN, Alwohaibi MA, White RE (1993) Using electrochemical impedance spectroscopy as a tool for organic coating solute saturation monitoring. J Electrochem Soc 140:947–951CrossRefGoogle Scholar
  121. Popova A, Christov M, Vasilev A (2011) Mono- and dicationic benzothiazolic quaternary ammonium bromides as mild steel corrosion inhibitors. Part II: electrochemical impedance and polarisation resistance results. Corros Sci 53:1770–1777CrossRefGoogle Scholar
  122. Poupard O, Ait-Mokhtar A, Dumargue P (2003) Impedance spectroscopy in reinforced concrete: experimental procedure for monitoring steel. Part I development of the experimental device. J Mater Sci 38:2845–2850CrossRefGoogle Scholar
  123. Rammelt U, Reinhard G (1992) Application of electrochemical impedance spectroscopy (EIS) for characterizing the corrosion-protective performance of organic coatings on metals. Prog Org Coat 21:205–226CrossRefGoogle Scholar
  124. Randles JEB (1947) Kinetics of rapid electrode reactions. Discuss Faraday Soc 1:11–19CrossRefGoogle Scholar
  125. Raps D, Hack T, Wehr J et al (2009) Electrochemical study of inhibitor-containing organic-inorganic hybrid coatings on AA2024. Corros Sci 51:1012–1021CrossRefGoogle Scholar
  126. Sagoe-Crentsil KK, Glasser FP, Irvine JTS (1992) Electrochemical characteristics of reinforced concrete corrosion as determined by impedance spectroscopy. Br Corros J 27:113–118CrossRefGoogle Scholar
  127. Scuderi CA, Mason TO, Jennings HM (1991) Impedance spectra of hydrating cement pastes. J Mater Sci 26:349–353CrossRefGoogle Scholar
  128. Scully JR (1989) Electrochemical impedance of organic-coated steel: correlation of impedance parameters with long-term coating deterioration. J Electrochem Soc 136:979–990CrossRefGoogle Scholar
  129. Scully JR, Hensley ST (1994) Lifetime prediction for organic coatings on steel and a magnesium alloy using electrochemical impedance methods. Corrosion 50:705–716CrossRefGoogle Scholar
  130. Sherif EM, Park S-M (2005) Effects of 1,5-naphthalenediol on aluminum corrosion as a corrosion inhibitor in 0.50 M NaCl. J Electrochem Soc 152:B205–B211CrossRefGoogle Scholar
  131. Sherif EM, Park SM (2006) Effects of 1,4-naphthoquinone on aluminum corrosion in 0.50 M sodium chloride solutions. Electrochim Acta 51:1313–1321CrossRefGoogle Scholar
  132. Shi Y, Tada E, Nishikata A (2015) A method for determining the corrosion rate of a metal under a thin electrolyte film. J Electrochem Soc 162:C135–C139CrossRefGoogle Scholar
  133. Shkirskiy V, Volovitch P, Vivier V (2017) Development of quantitative local electrochemical impedance mapping: an efficient tool for the evaluation of delamination kinetics. Electrochim Acta 235:442–452CrossRefGoogle Scholar
  134. Shreeram DD, Li S, Bedekar V et al (2017) Effect of reverse pulse time on electrodeposited Ni-W coatings. Surf Coat Technol 325:386–396CrossRefGoogle Scholar
  135. Sığırcık G, Yildirim D, Tüken T (2017) Synthesis and inhibitory effect of N,N’-bis(1-phenylethanol)ethylenediamine against steel corrosion in HCl media. Corros Sci 120:184–193CrossRefGoogle Scholar
  136. Singh SK, Tambe SP, Gunasekaran G et al (2009) Electrochemical impedance study of thermally sprayable polyethylene coatings. Corros Sci 51:595–601CrossRefGoogle Scholar
  137. Stafford OA, Hinderliter BR, Croll SG (2006) Electrochemical impedance spectroscopy response of water uptake in organic coatings by finite element methods. Electrochim Acta 52:1339–1348CrossRefGoogle Scholar
  138. Su Q, Allahar KN, Bierwagen GP (2008) Application of embedded sensors in the thermal cycling of organic coatings. Corros Sci 50:2381–2389CrossRefGoogle Scholar
  139. Su Q, Allahar KN, Bierwagen GP (2010) In situ embedded sensor monitoring of a United States Air Force primer beneath a topcoat exposed to atmospheric humidity and thermal conditions. Corrosion 66:066001-1–066001-12CrossRefGoogle Scholar
  140. Takeuchi K, Nishijima A, Ui K et al (2005) Corrosion behavior of Fe-Cr alloys in Li2CO3-K2CO3 molten carbonate. J Electrochem Soc 152:B364–B368CrossRefGoogle Scholar
  141. Tan YJ, Bailey S, Kinsella B (1996) An investigation of the formation and destruction of corrosion inhibitor films using electrochemical impedance spectroscopy (EIS). Corros Sci 38:1545–1561CrossRefGoogle Scholar
  142. Thee C, Hao L, Dong J et al (2014) Atmospheric corrosion monitoring of a weathering steel under an electrolyte film in cyclic wet-dry condition. Corros Sci 78:130–137CrossRefGoogle Scholar
  143. van der Weijde DH, van Westing EPM, de Wit JHW (1994) Electrochemical techniques for delamination studies. Corros Sci 36:643–652CrossRefGoogle Scholar
  144. van Westing EPM, Ferrari GM, de Wit JHW (1994) The determination of coating performance with impedance measurements-II. Water uptake of coatings. Corros Sci 36:957–977CrossRefGoogle Scholar
  145. Vedalakshmi R, Manoharan S, Song HW, Palaniswamy N (2009) Application of harmonic analysis in measuring the corrosion rate of rebar in concrete. Corros Sci 51:2777–2789CrossRefGoogle Scholar
  146. Vera Cruz RP, Nishikata A, Tsuru T (1996) AC impedance monitoring of pitting corrosion of stainless steel under a wet-dry cyclic condition in chloride-containing environment. Corros Sci 38:1397–1406CrossRefGoogle Scholar
  147. Walter GW (1991a) The application of impedance spectroscopy to study the uptake of sodium chloride solution in painted metals. Corros Sci 32:1041–1058CrossRefGoogle Scholar
  148. Walter GW (1991b) The application of impedance methods to study the effects of water uptake and chloride ion concentration on the degradation of paint films-I. Attached films. Corros Sci 32:1059–1084CrossRefGoogle Scholar
  149. Wittmann MW, Leggat RB, Taylor SR (1999) The detection and mapping of defects in organic coatings using local electrochemical impedance methods. J Electrochem Soc 146:4071–4075CrossRefGoogle Scholar
  150. Wu YM, Rapp RA (1991) Electrochemical impedance studies of hot corrosion of preoxidized Ni by a thin-fused Na2SO4 film. J Electrochem Soc 138:2683–2690CrossRefGoogle Scholar
  151. Yadav AP, Nishikata A, Tsuru T (2004a) Electrochemical impedance study on galvanized steel corrosion under cyclic wet-dry conditions-influence of time of wetness. Corros Sci 46:169–181CrossRefGoogle Scholar
  152. Yadav AP, Suzuki F, Nishikata A, Tsuru T (2004b) Investigation of atmospheric corrosion of Zn using ac impedance and differential pressure meter. Electrochim Acta 49:2725–2729CrossRefGoogle Scholar
  153. Yang BY, Kim KY (1999) The oxidation behavior of Ni-50%Co alloy electrode in molten Li+K carbonate eutectic. Electrochim Acta 44:2227–2234CrossRefGoogle Scholar
  154. Yeh TK, Chien YC, Wang BY, Tsai CH (2008) Electrochemical characteristics of zirconium oxide treated type 304 stainless steels of different surface oxide structures in high temperature water. Corros Sci 50:2327–2337CrossRefGoogle Scholar
  155. Zebardast HR, Rogak S, Asselin E (2013) Electrochemical detection of corrosion product fouling in high temperature and high pressure solution. Electrochim Acta 100:101–109CrossRefGoogle Scholar
  156. Zeng CL, Li J (2005) Electrochemical impedance studies of molten (0.9Na, 0.1K)2SO4-induced hot corrosion of the Ni-based superalloy M38G at 900 °C in air. Electrochim Acta 50:5533–5538CrossRefGoogle Scholar
  157. Zeng CL, Wang W, Wu WT (2000) Electrochemical-impedance study of the corrosion of Ni and FeAl intermetallic alloy in molten (0.62Li, 0.38K)2CO3 at 650 °C. Oxid Met 53:289–302CrossRefGoogle Scholar
  158. Zeng CL, Wang W, Wu WT (2001) Electrochemical impedance models for molten salt corrosion. Corros Sci 43:787–801CrossRefGoogle Scholar
  159. Zeng C, Guo P, Wu W (2004a) Electrochemical impedance of two-phase Ni-Ti alloys during corrosion in eutectic (0.62Li, 0.38K)2CO3 at 650 °C. Electrochim Acta 49:2271–2277CrossRefGoogle Scholar
  160. Zeng CL, Guo PY, Wu WT (2004b) Electrochemical impedance spectra for the corrosion of two-phase Cu-15Al alloy in eutectic (Li, K)2CO3 at 650 °C in air. Electrochim Acta 49:1445–1450Google Scholar
  161. Zeng Z, Lillard S, Cong H (2016) Effect of salt concentration on the corrosion behavior of carbon steel in CO2 environment. Corrosion 72:805–823CrossRefGoogle Scholar
  162. Zhang JT, Hu JM, Zhang JQ, Cao CN (2004) Studies of impedance models and water transport behaviors of polypropylene coated metals in NaCl solution. Prog Org Coat 49:293–301CrossRefGoogle Scholar
  163. Zhao Y, Zhou E, Liu Y et al (2017) Comparison of different electrochemical techniques for continuous monitoring of the microbiologically influenced corrosion of 2205 duplex stainless steel by marine Pseudomonas aeruginosa biofilm. Corros Sci 126:142–151CrossRefGoogle Scholar
  164. Zheludkevich ML, Yasakau KA, Poznyak SK, Ferreira MGS (2005) Triazole and thiazole derivatives as corrosion inhibitors for AA2024 aluminium alloy. Corros Sci 47:3368–3383CrossRefGoogle Scholar
  165. Zhou Q, Wang Y (2013) Comparisons of clear coating degradation in NaCl solution and pure water. Prog Org Coat 76:1674–1682CrossRefGoogle Scholar
  166. Zhou Q, Wang Y, Bierwagen GP (2012) Influence of the composition of working fluids on flow-accelerated organic coating degradation: deionized water versus electrolyte solution. Corros Sci 55:97–106CrossRefGoogle Scholar
  167. Zhou Q, Wang Y, Bierwagen GP (2014) Flow accelerated degradation of organic clear coat: the effect of fluid shear. Electrochim Acta 142:25–33CrossRefGoogle Scholar
  168. Zhu B, Lindbergh G, Simonsson D (1999) Comparision of electrochemical and surface characterisation methods for investigation of corrosion of bipolar plate materials in molten carbonate fuel cell: part I. Electrochemical study. Corros Sci 41:1497–1513CrossRefGoogle Scholar
  169. Zhu C, Xie R, Xue J, Song L (2011) Studies of the impedance models and water transport behaviors of cathodically polarized coating. Electrochim Acta 56:5828–5835CrossRefGoogle Scholar
  170. Zhu J, Xu L, Lu M (2015) Electrochemical impedance spectroscopy study of the corrosion of 3Cr pipeline steel in simulated CO2-saturated oilfield formation waters. Corrosion 71:854–864CrossRefGoogle Scholar

Copyright information

© Springer International Publishing AG, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Department of Chemical and Biomolecular Engineering, Corrosion Engineering ProgramThe University of AkronAkronUSA

Section editors and affiliations

  • Ida Nathan
    • 1
  • Norbert Meyendorf
    • 2
  1. 1.Department of Electrical and Computer EngineeringUniversity of AkronAkronUSA
  2. 2.Center for Nondestructive EvaluationIowa State UniversityAmesUSA

Personalised recommendations