1. Surface roughness effect on a magnetic fluid-based squeeze film between a curved porous circular plate and a flat circular plate

   • M. E. Shimpi
   • G. M. Deheri

   Technical Paper 09 August 2013 Pages: 233 - 243

   

2. Heat transfer to Herschel–Bulkley materials flowing in the entrance of tubes with an imposed wall temperature profile

   • Johnny Q. da Silva
   • Edson J. Soares
   • Rafhael M. Andrade

   Technical Paper 25 September 2013 Pages: 245 - 255

   

3. Optimization of a stochastic dynamical system

   • R. H. Lopez
   • T. G. Ritto
   • José Eduardo Souza de Cursi

   Technical Paper 08 August 2013 Pages: 257 - 264

   

4. Fatigue damage of a drilling tower induced by ocean waves

   • Victor F. D. Sacramento
   • Rubens Sampaio
   • Thiago G. Ritto

   Technical Paper 25 August 2013 Pages: 265 - 275

   

5. Analysis of structural reliability from time response using fully probabilistic

   • Fang Yongfeng
   • Chen Jianjun
   • Cao Hongjun

   Technical Paper 23 August 2013 Pages: 277 - 281

   

6. Modeling of piezoelectric energy harvesting considering the dependence of the rectifier circuit

   • Marcel Araujo Clementino
   • Romeu Reginatto
   • Samuel da Silva

   Technical Paper 29 August 2013 Pages: 283 - 292

   

7. Influence of substrate roughness on adhesion of TiN coatings

   • Aleksandar Miletić
   • Pal Terek
   • Dragan Kukuruzović

   Technical Paper 11 September 2013 Pages: 293 - 299

   

8. Multi-objective process optimization of wire electrical discharge machining based on response surface methodology

   • Danial Ghodsiyeh
   • Abolfazl Golshan
   • S. Izman

   Technical Paper 20 August 2013 Pages: 301 - 313

   

9. Simulation machining of titanium alloy (Ti-6Al-4V) based on the finite element modeling

   • Moaz H. Ali
   • M. N. M. Ansari
   • A. A. Oshkour

   Technical Paper 22 August 2013 Pages: 315 - 324

   

10. Simulation of the hone broaching process with diamond tools

    • Guilherme Evangelista Vargas
    • Konrad Wegener
    • Rolf Bertrand Schroeter

    Technical Paper 22 August 2013 Pages: 325 - 333

    

11. Wire electrical discharge machining of AA7075/SiC/Al₂O₃ hybrid composite fabricated by inert gas-assisted electromagnetic stir-casting process

    • Shyam Lal
    • Sudhir Kumar
    • A. N. Siddiquee

    Technical Paper 22 August 2013 Pages: 335 - 346

    

12. Investigation of burr formation and surface roughness in drilling engineering plastics

    • Mihrigul Altan
    • Erhan Altan

    Technical Paper 27 August 2013 Pages: 347 - 354

    

13. Modeling of residual stress distribution around fastener holes in thin plates after symmetric cold expansion

    • J. T. Maximov
    • G. V. Duncheva
    • I. M. Amudjev

    Technical Paper 08 September 2013 Pages: 355 - 369

    

14. Influence of friction parameters on springback and bend force in air bending of electrogalvanised steel sheet: an experimental study

    • R. Srinivasan
    • D. Vasudevan
    • P. Padmanabhan

    Technical Paper 08 September 2013 Pages: 371 - 376

    

15. Assessment of a transient homogeneous reactor through in situ adaptive tabulation

    • Americo Cunha Jr
    • Luís Fernando Figueira da Silva

    Technical Paper 23 August 2013 Pages: 377 - 391

    

16. Thermoanalysis and reaction kinetics of heavy oil combustion

    • Anderson N. Pereira
    • Osvair V. Trevisan

    Technical Paper 17 September 2013 Pages: 393 - 401

    

17. Combustion time of the oxygenated and non-oxygenated fuels in an Otto cycle engine

    • Pedro Mello
    • Fabiano Wildner
    • Rosângela da Silva

    Technical Paper Open access 27 October 2013 Pages: 403 - 410

    

18. Experimental study of mixing layer in a closed compound channel

    • Jhon Goulart
    • Luciano Noleto
    • Sérgio V. Möller

    Technical Paper 21 August 2013 Pages: 411 - 420

    

19. Trap based part feeding system for stacking sector shaped parts

    • S. Udhayakumar
    • P. V. Mohanram
    • R. Srinivasan

    Technical Paper 20 August 2013 Pages: 421 - 431