1. Global sensitivity analysis and coupling effects of forming parameters on wall thinning and cross-sectional distortion of rotary draw bending of thin-walled rectangular tube with small bending radius

   • H. P. Li
   • Y. L. Liu
   • H. Yang

   ORIGINAL ARTICLE 07 June 2014 Pages: 581 - 589

2. Simulation model of debris and bubble movement in electrode jump of electrical discharge machining

   • Jin Wang
   • Fuzhu Han

   ORIGINAL ARTICLE 07 June 2014 Pages: 591 - 598

3. Use of electrical insulation of the cutting tool to increase tool life when machining titanium alloys

   • Vladimir F. Pegashkin
   • Valentin I. Golubev
   • Vitaly V. Medison

   ORIGINAL ARTICLE 07 June 2014 Pages: 599 - 614

4. Study and improvement of surgical drill bit geometry for implant site preparation

   • Josu Soriano
   • Ainhara Garay
   • Pedro J. Arrazola

   ORIGINAL ARTICLE 07 June 2014 Pages: 615 - 627

5. Enhancement optimization of drivable terrain detection system for autonomous robots in light intensity scenario

   • Olusanya Y. Agunbiade
   • Seleman M. Ngwira
   • Tranos Zuva

   ORIGINAL ARTICLE 08 June 2014 Pages: 629 - 636

6. Application of knowledge-based engineering for automated slide design

   • Wen-Ren Jong
   • Yu-Hung Ting
   • Tai-Chih Li

   ORIGINAL ARTICLE 08 June 2014 Pages: 637 - 651

7. Surface roughness prediction and parameters optimization in grinding and polishing process for IBR of aero-engine

   • Tao Zhao
   • Yaoyao Shi
   • Jun Zhang

   ORIGINAL ARTICLE 08 June 2014 Pages: 653 - 663

8. Numerical simulation of gear surface hardening using the finite element method

   • Bin He
   • Shan Huang
   • Xiaolin He

   ORIGINAL ARTICLE 08 June 2014 Pages: 665 - 672

9. Plastic deformation behavior of the friction stir welded AA2024 aluminum alloy

   • Peng Zhang
   • Ning Guo
   • Jicai Feng

   ORIGINAL ARTICLE 10 June 2014 Pages: 673 - 679

10. Temperature-sensitive point selection of thermal error model of CNC machining center

    • Miao En-ming
    • Gong Ya-yun
    • Miao Ji-chao

    ORIGINAL ARTICLE 10 June 2014 Pages: 681 - 691

11. Droplet rebounded spatter in dry hyperbaric gas metal arc welding process

    • Kai Li
    • Hongming Gao
    • Shan Gong

    ORIGINAL ARTICLE 10 June 2014 Pages: 693 - 698

12. Effect of underfill defects on distortion and tensile properties of Ti-2Al-1.5Mn welded joint by pulsed laser beam welding

    • Xiuyang Fang
    • Jianxun Zhang

    ORIGINAL ARTICLE 10 June 2014 Pages: 699 - 705

13. Fractal characterization of the friction forces of a graded ceramic tool material

    • Guangming Zheng
    • Jun Zhao
    • Li Li

    ORIGINAL ARTICLE 10 June 2014 Pages: 707 - 714

14. An adaptive CONWIP mechanism for hybrid production systems

    • Aybek Korugan
    • Surendra M. Gupta

    ORIGINAL ARTICLE 10 June 2014 Pages: 715 - 727

15. Kinematic design of a novel 4-DOF parallel mechanism for turbine blade machining

    • Hiwa Ghaffari
    • Gholamhasan Payeganeh
    • Mohammadreza Arbabtafti

    ORIGINAL ARTICLE 10 June 2014 Pages: 729 - 739

16. Manufacturing tactile spherical stylus tips by combination process of micro electro chemical and one-pulse electro discharge technology

    • Dong-Yea Sheu

    ORIGINAL ARTICLE 11 June 2014 Pages: 741 - 747

17. Multiphysics research in electrochemical machining of internal spiral hole

    • Minghuan Wang
    • Wangsheng Liu
    • Wei Peng

    ORIGINAL ARTICLE 11 June 2014 Pages: 749 - 756

18. Multiobjective parallel machine scheduling in the sawmill industry using memetic algorithms

    • Felipe Baesler
    • Cristian Palma

    ORIGINAL ARTICLE 11 June 2014 Pages: 757 - 768

19. Nanosecond Yb fibre laser milling of aluminium: effect of process parameters on the achievable surface finish and machining efficiency

    • E. Williams
    • E. B. Brousseau
    • A. Rees

    ORIGINAL ARTICLE 11 June 2014 Pages: 769 - 780

20. A study of helical passageways applied to polygon holes in abrasive flow machining

    • Kuan-Yu Chen
    • Ken-Chuan Cheng

    ORIGINAL ARTICLE 11 June 2014 Pages: 781 - 790

21. Two-sided assembly line balancing with operator number and task constraints: a hybrid imperialist competitive algorithm

    • Baoxi Wang
    • Zailin Guan
    • Lei Chen

    ORIGINAL ARTICLE 11 June 2014 Pages: 791 - 805

22. Experimental study and genetic algorithm-based optimization of cutting parameters in cutting engineering ceramics

    • Xiaohui Chen
    • Lianjie Ma
    • Xiaobing Cao

    ORIGINAL ARTICLE 11 June 2014 Pages: 807 - 817

23. A note on “A mathematical model and extension algorithm for assembly flexible flow shop scheduling problem”

    • Hongying Shan
    • Tsui-Ping Chung
    • LuLu Hu

    ORIGINAL ARTICLE 12 June 2014 Pages: 819 - 822

24. Simulation scan comparison for process monitoring using 3D scanning in manufacturing environments

    • Steven McAtee
    • Michelle Dunn
    • Romesh Nagarajah

    ORIGINAL ARTICLE 12 June 2014 Pages: 823 - 834

25. Modeling the operation of a common grinding wheel with nanoparticle jet flow minimal quantity lubrication

    • Sheng Wang
    • Changhe Li
    • Yanbin Zhang

    ORIGINAL ARTICLE 12 June 2014 Pages: 835 - 850

26. A web-based 3D modeling framework for a runner-gate design

    • Nyamsuren Purevdorj
    • Soo-Hong Lee
    • Hyun-Tae Hwang

    Original Paper 13 June 2014 Pages: 851 - 858

27. A novel sheet metal forming technology to enhance formability of FVS0812 sheet

    • Y. R. Tao
    • Sh. Y. Duan
    • B. Jiang

    ORIGINAL ARTICLE 13 June 2014 Pages: 859 - 866

28. Statistical analysis and optimization of processing parameters in high-power direct diode laser cladding

    • Shuang Liu
    • Radovan Kovacevic

    ORIGINAL ARTICLE 14 June 2014 Pages: 867 - 878

29. Simultaneous optimization of surface roughness and material removal rate for turning of X20Cr13 stainless steel

    • Lakhdar Bouzid
    • Smail Boutabba
    • Francois Girardin

    ORIGINAL ARTICLE 14 June 2014 Pages: 879 - 891

30. Identification of mechanical properties of the weld line by combining 3D digital image correlation with inverse modeling procedure

    • Guangyao Li
    • Fengxiang Xu
    • Qing Li

    ORIGINAL ARTICLE 14 June 2014 Pages: 893 - 905

31. Injection molding of nanopatterned surfaces in the sub-micrometer range with induction heating aid

    • Stefano Menotti
    • Hans N. Hansen
    • Christian Ravn

    ORIGINAL ARTICLE 17 June 2014 Pages: 907 - 916

32. An analysis and optimization of the geometrical inaccuracy in WEDM rough corner cutting

    • Zhi Chen
    • Yu Huang
    • Guojun Zhang

    ORIGINAL ARTICLE 17 June 2014 Pages: 917 - 929

33. An elastic model of tool lifespan for small-lot production

    • Cun Rong Li
    • Xian Mu Zhang
    • Bhaba R. Sarker

    ORIGINAL ARTICLE 17 June 2014 Pages: 931 - 941

34. CFD 2D simulation of viscous flow during ECAE through a rectangular die with parallel slants

    • Alexander V. Perig
    • Nikolai N. Golodenko

    ORIGINAL ARTICLE 17 June 2014 Pages: 943 - 962

    

35. Investigation of tool geometry effect and penetration strategies on cutting forces during thread milling

    • Vishal S. Sharma
    • Guillaume Fromentin
    • Romain Brendlen

    ORIGINAL ARTICLE 17 June 2014 Pages: 963 - 971

36. A model of non-linear cumulative damage to tools at changing cutting speeds

    • Z. Pálmai

    ORIGINAL ARTICLE 17 June 2014 Pages: 973 - 982

37. Mechanical and tribological properties of hot-pressed electrospun MWCNTs/carbon nanofibril composite fabrics

    • Ashraf A. Ali
    • A. R. Eldesouky
    • Said H. Zoalfakar

    ORIGINAL ARTICLE 17 June 2014 Pages: 983 - 993

38. Investigating the effects of cross wedge rolling tool parameters on formability of Nimonic® 80A and Nimonic® 115 superalloys

    • S. Javid Mirahmadi
    • Mohsen Hamedi
    • Shahabeddin Ajami

    ORIGINAL ARTICLE 17 June 2014 Pages: 995 - 1004

39. Balancing of robotic mixed-model two-sided assembly line with robot setup times

    • Mojtaba Aghajani
    • Reza Ghodsi
    • Babak Javadi

    ORIGINAL ARTICLE 18 June 2014 Pages: 1005 - 1016

40. Robust design modeling and optimization of a multi-response time series for a pharmaceutical process

    • Sangmun Shin
    • Nguyen Khoa Viet Truong
    • Seong Hoon Jeong

    ORIGINAL ARTICLE 19 June 2014 Pages: 1017 - 1031

41. Ontology-driven generation of Bayesian diagnostic models for assembly systems

    • Mohamed S. Sayed
    • Niels Lohse

    ORIGINAL ARTICLE 19 June 2014 Pages: 1033 - 1052

42. Superconducting EMS feed drive system of NC machine tool

    • Wenxue Jiang
    • Kai Zhou
    • Yanwu Men

    ORIGINAL ARTICLE 20 June 2014 Pages: 1053 - 1060

43. An optimization design of the 3-EWMA scheme for monitoring mean shifts

    • M. Shamsuzzaman
    • M. B. C. Khoo
    • I. Alsyouf

    ORIGINAL ARTICLE 20 June 2014 Pages: 1061 - 1076

44. New concept for micro-manipulation systems: a practical experience

    • Cristiana Delprete
    • Carlo Rosso
    • Cristina Scarzella

    ORIGINAL ARTICLE 20 June 2014 Pages: 1077 - 1085

45. Microstructural, mechanical, and thermophysical characterization of Cu/WC composite layers fabricated via friction stir processing

    • Jahangir Khosravi
    • Mohammad Kazem Beshrati Givi
    • Abbas Rahi

    ORIGINAL ARTICLE 20 June 2014 Pages: 1087 - 1096

46. A coupling motional control method based on parametric predictive and variable universe fuzzy control for multi-axis CNC machine tools

    • Libing Zhang
    • Ting Wu
    • Fengli Huang

    ORIGINAL ARTICLE 21 June 2014 Pages: 1097 - 1114

47. Application of a hybrid process for high precision manufacture of difficult to machine prismatic parts

    • Zicheng Zhu
    • Vimal Dhokia
    • Aydin Nassehi

    ORIGINAL ARTICLE 21 June 2014 Pages: 1115 - 1132

48. Temperature variation in the workpiece and in the cutting tool when dry milling Inconel 718

    • G. Le Coz
    • D. Dudzinski

    ORIGINAL ARTICLE 22 June 2014 Pages: 1133 - 1139

49. Selecting and full ranking suppliers with imprecise data: A new DEA method

    • Mehdi Toloo

    ORIGINAL ARTICLE 24 June 2014 Pages: 1141 - 1148

50. A multiple objective stochastic approach to vehicle routing problem

    • Yahia Zare Mehrjerdi

    ORIGINAL ARTICLE 24 June 2014 Pages: 1149 - 1158