1. Applying forming simulation to process and tooling designs for minimizing springback in split dowel manufacturing

   • Jenn-Terng Gau
   • Adam D. Dye
   • Chet Arciuch

   ORIGINAL ARTICLE 17 November 2006 Pages: 423 - 433

2. Bootstrap method approach in designing multi-attribute control charts

   • Seyed Taghi Akhavan Niaki
   • Babak Abbasi

   ORIGINAL ARTICLE 06 October 2006 Pages: 434 - 442

3. CBN tool wear in hard turning: a survey on research progresses

   • Yong Huang
   • Y. Kevin Chou
   • Steven Y. Liang

   ORIGINAL ARTICLE 08 November 2006 Pages: 443 - 453

4. Monitoring of diamond disk wear in stone cutting by means of force or acceleration sensors

   • W. Polini
   • S. Turchetta

   ORIGINAL ARTICLE 06 October 2006 Pages: 454 - 467

5. Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology

   • Ko-Ta Chiang
   • Fu-Ping Chang

   ORIGINAL ARTICLE 06 October 2006 Pages: 468 - 479

6. The development of adaptive modified appearance using operating window methods for optimizing electron beam

   • Ming-Der Jean
   • Bor-Tsuen Lin
   • Jyh-Horng Chou

   ORIGINAL ARTICLE 21 September 2006 Pages: 480 - 492

7. Discussion on the problems related to NC machining of toroid-shaped taper cutter with constant angle between cutting edge and the cutter axis

   • Ching-Ben Chen

   ORIGINAL ARTICLE 06 July 2007 Pages: 493 - 504

8. A universal velocity profile generation approach for high-speed machining of small line segments with look-ahead

   • Fu-Yuan Luo
   • Yun-Fei Zhou
   • Juan Yin

   ORIGINAL ARTICLE 08 November 2006 Pages: 505 - 518

9. Cost-competent tolerancing in CAD

   • S. Ch. Dimitrellou
   • S. C. Diplaris
   • M. M. Sfantsikopoulos

   ORIGINAL ARTICLE 02 November 2006 Pages: 519 - 526

10. Automatic generation of PLC automation projects from component-based models

    • Elisabet Estévez
    • Marga Marcos
    • Darío Orive

    ORIGINAL ARTICLE 18 July 2007 Pages: 527 - 540

11. Using ant colony optimization to solve hybrid flow shop scheduling problems

    • Kemal Alaykýran
    • Orhan Engin
    • Alper Döyen

    ORIGINAL ARTICLE 24 May 2007 Pages: 541 - 550

12. No-wait flowshop with separate setup times to minimize maximum lateness

    • Rubén Ruiz
    • Ali Allahverdi

    ORIGINAL ARTICLE 14 November 2006 Pages: 551 - 565

13. A scheduling algorithm for the reentrant shop: an application in semiconductor manufacture

    • Yong-Ha Kang
    • Sung-Shick Kim
    • Hyun Joon Shin

    ORIGINAL ARTICLE 09 November 2006 Pages: 566 - 574

14. A hybrid look-ahead SOM-FBPN and FIR system for wafer-lot-output time prediction and achievability evaluation

    • Toly Chen

    ORIGINAL ARTICLE 22 November 2006 Pages: 575 - 586

15. A joint GA+DP approach for single burn-in oven scheduling problems with makespan criterion

    • Fuh-Der Chou

    ORIGINAL ARTICLE 17 November 2006 Pages: 587 - 595

16. Design of due-date oriented look-ahead batching rule in wafer fabrication

    • D. Y. Sha
    • Sheng-Yuan Hsu
    • X. D. Lai

    ORIGINAL ARTICLE 22 November 2006 Pages: 596 - 609

17. A particle swarm optimization approach to optimize component placement in printed circuit board assembly

    • Yee-Ming Chen
    • Chun-Ta Lin

    ORIGINAL ARTICLE 25 November 2006 Pages: 610 - 620

18. Efficiency measurement for multi-dimensional group technology

    • Ming-Liang Li

    ORIGINAL ARTICLE 06 December 2006 Pages: 621 - 632