1. Thank you to our Reviewers

   Editorial 03 March 2018 Pages: 1 - 2

2. An automated CFD analysis workflow in overall aircraft design applications

   • Xiangyu Gu
   • Pier Davide Ciampa
   • Björn Nagel

   Original Paper Open access 28 October 2017 Pages: 3 - 13

   

3. Analysis and design of hybrid electric regional turboprop aircraft

   • Mark Voskuijl
   • Joris van Bogaert
   • Arvind G. Rao

   Original Paper Open access 31 October 2017 Pages: 15 - 25

   

4. Tactile cueing with active cyclic stick for helicopter obstacle avoidance: development and pilot acceptance

   • Mario Müllhäuser

   Original Paper 31 October 2017 Pages: 27 - 37

   

5. Influence of a back-flow flap on the dynamic stall flow topology

   • C. C. Wolf
   • A. D. Gardner
   • S. Opitz

   Original Paper 13 November 2017 Pages: 39 - 51

   

6. Quasi-steady doublet-lattice correction for aerodynamic gust response prediction in attached and separated transonic flow

   • Diliana Friedewald
   • Reik Thormann
   • Jens Nitzsche

   Original Paper 17 November 2017 Pages: 53 - 66

   

7. About the impact of wind turbine blade tip vortices on helicopter rotor trim and rotor blade motion

   • Berend G. van der Wall
   • Paul H. Lehmann

   Original Paper 12 December 2017 Pages: 67 - 84

   

8. Future regeneration processes for high-pressure turbine blades

   • M. Nicolaus
   • B. Rottwinkel
   • V. Wesling

   Original Paper 26 December 2017 Pages: 85 - 92

   

9. Unsteady aerodynamics of a diamond wing configuration

   • Stefan Pfnür
   • Christian Breitsamter

   Original Paper 12 January 2018 Pages: 93 - 112

   

10. AAA process: a new approach to affordable fly-by-wire systems for CS23 aircraft

    • P. Mueller
    • T. Belschner
    • R. Reichel

    Original Paper 15 January 2018 Pages: 113 - 122

    

11. In-situ structural evaluation during the fibre deposition process of composite manufacturing

    • F. Heinecke
    • T. Wille

    Original Paper 18 January 2018 Pages: 123 - 133

    

12. Comparison of sensitivities to geometrical properties of front and aft high pressure compressor stages

    • G. Reitz
    • A. Kellersmann
    • J. Friedrichs

    Original Paper 18 January 2018 Pages: 135 - 146

    

13. Evaluation of assemblability during aero engine preliminary design

    • J. Mall
    • S. Staudacher

    Original Paper 19 January 2018 Pages: 147 - 156

    

14. A practical example for validation of ATM security prototypes

    • Michael Finke
    • Tim H. Stelkens-Kobsch

    Original Paper Open access 24 January 2018 Pages: 157 - 170

    

15. Reduced-order models for aerodynamic applications, loads and MDO

    • M. Ripepi
    • M. J. Verveld
    • T. M. Kier

    Original Paper 10 February 2018 Pages: 171 - 193

    

16. Numerical investigation of slot variations on the efficiency of tangential blowing at a vertical tailplane with infinite span

    • A. Gebhardt
    • J. Kirz

    Original Paper 16 February 2018 Pages: 195 - 206

    

17. HALO flight test with instrumented under-wing stores for aeroelastic and load measurements in the DLR project iLOADS

    • J. Sinske
    • Y. Govers
    • M. Böswald

    Original Paper Open access 27 February 2018 Pages: 207 - 218

    

18. Influence of engine modeling on structural sizing and approach aerodynamics of a circulation controlled wing

    • Kay Sommerwerk
    • Benedikt Michels
    • Peter Horst

    Original Paper 27 February 2018 Pages: 219 - 233

    

19. Novel epoxy prepreg resins for aircraft interiors based on combinations of halogen-free flame retardants

    • Thomas Neumeyer
    • Anika Bauernfeind
    • Volker Altstaedt

    Original Paper 05 March 2018 Pages: 235 - 248