Volume 9, issue 1, March 2018

19 articles in this issue

Thank you to our Reviewers
- Content type: Editorial
- Published: 03 March 2018
- Pages: 1 - 2
An automated CFD analysis workflow in overall aircraft design applications

Authors
- Xiangyu Gu
- Pier Davide Ciampa
- Björn Nagel
- Content type: Original Paper
- Open Access
- Published: 28 October 2017
- Pages: 3 - 13
Analysis and design of hybrid electric regional turboprop aircraft

Authors
- Mark Voskuijl
- Joris van Bogaert
- Arvind G. Rao
- Content type: Original Paper
- Open Access
- Published: 31 October 2017
- Pages: 15 - 25
Tactile cueing with active cyclic stick for helicopter obstacle avoidance: development and pilot acceptance

Authors
- Mario Müllhäuser
- Content type: Original Paper
- Published: 31 October 2017
- Pages: 27 - 37
Influence of a back-flow flap on the dynamic stall flow topology

Authors (first, second and last of 4)
- C. C. Wolf
- A. D. Gardner
- S. Opitz
- Content type: Original Paper
- Published: 13 November 2017
- Pages: 39 - 51
Quasi-steady doublet-lattice correction for aerodynamic gust response prediction in attached and separated transonic flow

Authors (first, second and last of 4)
- Diliana Friedewald
- Reik Thormann
- Jens Nitzsche
- Content type: Original Paper
- Published: 17 November 2017
- Pages: 53 - 66
About the impact of wind turbine blade tip vortices on helicopter rotor trim and rotor blade motion

Authors
- Berend G. van der Wall
- Paul H. Lehmann
- Content type: Original Paper
- Published: 12 December 2017
- Pages: 67 - 84
Future regeneration processes for high-pressure turbine blades

Authors (first, second and last of 8)
- M. Nicolaus
- B. Rottwinkel
- V. Wesling
- Content type: Original Paper
- Published: 26 December 2017
- Pages: 85 - 92
Unsteady aerodynamics of a diamond wing configuration

Authors
- Stefan Pfnür
- Christian Breitsamter
- Content type: Original Paper
- Published: 12 January 2018
- Pages: 93 - 112
AAA process: a new approach to affordable fly-by-wire systems for CS23 aircraft

Authors (first, second and last of 4)
- P. Mueller
- T. Belschner
- R. Reichel
- Content type: Original Paper
- Published: 15 January 2018
- Pages: 113 - 122
In-situ structural evaluation during the fibre deposition process of composite manufacturing

Authors
- F. Heinecke
- T. Wille
- Content type: Original Paper
- Published: 18 January 2018
- Pages: 123 - 133
Comparison of sensitivities to geometrical properties of front and aft high pressure compressor stages

Authors (first, second and last of 4)
- G. Reitz
- A. Kellersmann
- J. Friedrichs
- Content type: Original Paper
- Published: 18 January 2018
- Pages: 135 - 146
Evaluation of assemblability during aero engine preliminary design

Authors
- J. Mall
- S. Staudacher
- Content type: Original Paper
- Published: 19 January 2018
- Pages: 147 - 156
A practical example for validation of ATM security prototypes

Authors
- Michael Finke
- Tim H. Stelkens-Kobsch
- Content type: Original Paper
- Open Access
- Published: 24 January 2018
- Pages: 157 - 170
Reduced-order models for aerodynamic applications, loads and MDO

Authors (first, second and last of 7)
- M. Ripepi
- M. J. Verveld
- T. M. Kier
- Content type: Original Paper
- Published: 10 February 2018
- Pages: 171 - 193
Numerical investigation of slot variations on the efficiency of tangential blowing at a vertical tailplane with infinite span

Authors
- A. Gebhardt
- J. Kirz
- Content type: Original Paper
- Published: 16 February 2018
- Pages: 195 - 206
HALO flight test with instrumented under-wing stores for aeroelastic and load measurements in the DLR project iLOADS

Authors (first, second and last of 6)
- J. Sinske
- Y. Govers
- M. Böswald
- Content type: Original Paper
- Open Access
- Published: 27 February 2018
- Pages: 207 - 218
Influence of engine modeling on structural sizing and approach aerodynamics of a circulation controlled wing

Authors (first, second and last of 4)
- Kay Sommerwerk
- Benedikt Michels
- Peter Horst
- Content type: Original Paper
- Published: 27 February 2018
- Pages: 219 - 233
Novel epoxy prepreg resins for aircraft interiors based on combinations of halogen-free flame retardants

Authors (first, second and last of 6)
- Thomas Neumeyer
- Anika Bauernfeind
- Volker Altstaedt
- Content type: Original Paper
- Published: 05 March 2018
- Pages: 235 - 248

Volume 9, issue 1, March 2018

Thank you to our Reviewers

An automated CFD analysis workflow in overall aircraft design applications

Analysis and design of hybrid electric regional turboprop aircraft

Tactile cueing with active cyclic stick for helicopter obstacle avoidance: development and pilot acceptance

Influence of a back-flow flap on the dynamic stall flow topology

Quasi-steady doublet-lattice correction for aerodynamic gust response prediction in attached and separated transonic flow

About the impact of wind turbine blade tip vortices on helicopter rotor trim and rotor blade motion

Future regeneration processes for high-pressure turbine blades

Unsteady aerodynamics of a diamond wing configuration

AAA process: a new approach to affordable fly-by-wire systems for CS23 aircraft

In-situ structural evaluation during the fibre deposition process of composite manufacturing

Comparison of sensitivities to geometrical properties of front and aft high pressure compressor stages

Evaluation of assemblability during aero engine preliminary design

A practical example for validation of ATM security prototypes

Reduced-order models for aerodynamic applications, loads and MDO

Numerical investigation of slot variations on the efficiency of tangential blowing at a vertical tailplane with infinite span

HALO flight test with instrumented under-wing stores for aeroelastic and load measurements in the DLR project iLOADS

Influence of engine modeling on structural sizing and approach aerodynamics of a circulation controlled wing

Novel epoxy prepreg resins for aircraft interiors based on combinations of halogen-free flame retardants

For authors

Working on a manuscript?

Explore

Navigation

Volume 9, issue 1, March 2018

Authors

Authors

Authors

Authors (first, second and last of 4)

Authors (first, second and last of 4)

Authors

Authors (first, second and last of 8)

Authors

Authors (first, second and last of 4)

Authors

Authors (first, second and last of 4)

Authors

Authors

Authors (first, second and last of 7)

Authors

Authors (first, second and last of 6)

Authors (first, second and last of 4)

Authors (first, second and last of 6)

For authors

Working on a manuscript?

Explore

search

Navigation