1. Improved modeling of the effects of thermal residual stresses on single fiber pull-out problem

   • Young Suk Chai
   • Byung Sun Choi
   • Kyung Jun Yang

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 823 - 830

2. A new approach for pulsating torque minimization of BLDC motor

   • Young-Jin Lee
   • Man Hyung Lee
   • Han-Woong Park

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 831 - 838

3. A study on the warm deep drawability of sheets in Cr-coated die

   • Jae Dong Lee
   • Young Moo Heo
   • Dae Gyo Seo

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 839 - 846

4. A study on the control model identification andH∞ controller design for tandem cold mills

   • Man Hyung Lee
   • Yu Shin Chang
   • In-Soo Kim

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 847 - 858

5. Calculation of mixed lubrication at piston ring and cylinder liner interface

   • Myung-Rae Cho
   • Jae-Kwon Choi
   • Dong-Chul Han

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 859 - 865

6. Complex modal testing of asymmetric rotors using magnetic exciter equipped with hall sensors

   • Chong-Won Lee
   • Si-Kyoung Kim

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 866 - 875

7. Efficient approximation method for constructing quadratic response surface model

   • Kyung-Jin Hong
   • Min-Soo Kim
   • Dong-Hoon Choi

   Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 876 - 888

8. Assessment of reynolds stress turbulence closures in the calculation of a transonic separated flow

   • Kwang-Yong Kim
   • Jong-Woo Son
   • Chang-Ho Cho

   Thermal Engineering · Fluid Engineering · Energy and Power Engineering Pages: 889 - 894

9. Investigation of the three-dimensional turbulent flow fields of the gas swirl burner with a cone type baffle plate (I)

   • Jang-kweon Kim

   Thermal Engineering · Fluid Engineering · Energy and Power Engineering Pages: 895 - 905

10. Investigation of the three-dimensional turbulent flow fields of the gas swirl burner with a cone type baffle plate (II)

    • Jang-kweon Kim

    Thermal Engineering · Fluid Engineering · Energy and Power Engineering Pages: 906 - 920

11. A theoretical model of critical heat flux in flow boiling at low qualities

    • Hyuk Sung Kwon
    • Dae Hyun Hwang
    • Yongchan Kim

    Thermal Engineering · Fluid Engineering · Energy and Power Engineering Pages: 921 - 930

12. Numerical study on a sliding bubble during nucleate boiling

    • Gihun Son

    Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 931 - 940

13. Two-phase flow regimes for counter-current air-water flows in narrow rectangular channels

    • Byong Joo Kim
    • Byung Hu Sohn
    • Siyoung Jeong

    Materials & Fracture · Solids & Structures · Dynamics & Control · Production & Design Pages: 941 - 950

14. Development and application of a new spray impingement model considering film formation in a diesel engine

    • Seong Hyuk Lee
    • Gwon Hyun Ko
    • Ki Bae Hong

    Thermal Engineering · Fluid Engineering · Energy and Power Engineering Pages: 951 - 961

15. Effect of residual stress on femoral arterial stress-strain behavior

    • K. B. Chandran
    • J. H. Mun
    • D. D. McPherson

    Special Issue in Biomechanics Pages: 965 - 973

16. Normal and reconstructed mandibular condyle mechanics

    • S. J. Hollister
    • S. E. Feinberg

    Special Issue in Biomechanics Pages: 974 - 981

17. Modelling of ergonomics and muscular comfort

    • Eberhard Haug
    • Alain Trameçon
    • Hyung-Yun Choi

    Special Issue in Biomechanics Pages: 982 - 994

18. Numerical human head model for traumatic injury assessment

    • Hyung-Yun Choi

    Special Issue in Biomechanics Pages: 995 - 1001

19. Constitutive model of tendon responses to multiple cyclic demands (I)

    • Keyoung Jin Chun
    • Robert P. Hubbard

    Special Issue in Biomechanics Pages: 1002 - 1012

20. Mechanical properties of different anatomical sites of the bone-tendon origin of lateral epicondyle

    • Jung Soo Han

    Special Issue in Biomechanics Pages: 1013 - 1021

21. The elastic moduli and fatigue properties of canine trabecular bone tissue

    • Kuiwon Choi
    • Gon Khang
    • Steven A. Goldstein

    Special Issue in Biomechanics Pages: 1022 - 1031

22. Strain rate dependent poroelastic behavior of bovine vertebral trabecular bone

    • Jung Hwa Hong
    • Mu Seong Mun
    • Tae-Hong Lim

    Special Issue in Biomechanics Pages: 1032 - 1040

23. Prediction of cement volume for vertebroplasty based on imaging and biomechanical results

    • Gye-Rae Tack
    • Seung-Yong Lee
    • Kyu-Chul Shin

    Special Issue in Biomechanics Pages: 1041 - 1050

24. Flow visualizations and hot-wire measurements on air flow in two different neonate incubators

    • Seoung-Chool Yoo
    • Young-Ho Kim
    • Chi-Ho Kwon

    Special Issue in Biomechanics Pages: 1051 - 1060

25. Analysis of design parameters for shunt valve and anti-siphon device used to treat patients with hydrocephalus

    • Jong Yun Jang
    • Chang Min Suh
    • Chong Sun Lee

    Special Issue in Biomechanics Pages: 1061 - 1071

26. Biomechanical effect of in-line skating wrist guards on the prevention of wrist fracture

    • Linda M. McGrady
    • Peter Hoepfner
    • Jung Soo Han

    Special Issue in Biomechanics Pages: 1072 - 1076