1. Using the achievements in tribology for teaching technical disciplines

   • Yu. N. Drozdov
   • N. V. Lukashina
   • T. I. Nazarova

   General Issue of Machine Engineering 17 April 2011 Pages: 97 - 101

2. A method to determine the mass and coordinates of the center of mass of a body in a given plane

   • A. K. Aleshin

   Machinery Mechanics 17 April 2011 Pages: 102 - 106

3. Primary deviations of mechanism links with sliding and revolute pairs

   • N. A. Serkov

   Machinery Mechanics 17 April 2011 Pages: 107 - 112

4. Investigation of oscillation modes based on numerical solutions of nonlinear models

   • B. G. Kukharenko

   Machinery Mechanics 17 April 2011 Pages: 113 - 119

5. Micromechanics of metal failure in a complex stress state

   • B. I. Zavoichinskii
   • E. B. Zavoichinskaya

   Reliability, Durability, and Wear Resistance of Machines and Constructions 17 April 2011 Pages: 120 - 126

6. Local surface defects of composite plates

   • P. B. Fedorov

   Reliability, Durability, and Wear Resistance of Machines and Constructions 17 April 2011 Pages: 127 - 130

7. A method to estimate the metallic material erosion resistance according to energy criterion

   • L. I. Pogodaev
   • D. F. Donskikh

   Reliability, Durability, and Wear Resistance of Machines and Constructions 17 April 2011 Pages: 131 - 134

8. The influence of the composition of nanostructural PSZ powders on ceramics wear

   • V. G. Lapteva
   • V. V. Alisin
   • I. A. Khrennikova

   Reliability, Durability, and Wear Resistance of Machines and Constructions 17 April 2011 Pages: 135 - 139

9. Formation of a flange from a flat blank with a hole

   • R. I. Nepershin

   New Technology in Machinery Manufacture 17 April 2011 Pages: 140 - 148

10. Increasing the safety and efficiency of metal cooling in the process of fabricating a hollow mold

    • V. V. Stulov
    • A. M. Sevastyanov

    New Technology in Machinery Manufacture 17 April 2011 Pages: 149 - 153

11. Energy peculiarities and accelerations during reversible and irreversible deformations

    • Yu. A. Alyushin
    • M. M. Skripalenko

    New Technology in Machinery Manufacture 17 April 2011 Pages: 154 - 160

12. Aging nonlinear oscillator

    • B. A. Shcheglov

    Experimental Machine Mechanics, Diagnostics, and Testing 17 April 2011 Pages: 161 - 164

13. Complex examination of a spindle drive unit of a profile-grinding machine

    • A. M. Shitov

    Experimental Machine Mechanics, Diagnostics, and Testing 17 April 2011 Pages: 165 - 170

14. Improvement of the acceptance test procedure for the external combustion engine after assembly by using the relationship between diagnostic parameters

    • K. N. Osipov
    • E. L. Pervukhina
    • Yu. L. Rapatskii

    Experimental Machine Mechanics, Diagnostics, and Testing 17 April 2011 Pages: 171 - 175

15. Operation survivability of civil aircraft

    • B. G. Nesterenko

    Technogenic Safety of Vehicles and Designs 17 April 2011 Pages: 176 - 189

16. A method to calculate the reliability of the gas pipeline segment under axial compression

    • V. I. Kucheryavyi
    • S. N. Mil’kov

    Technogenic Safety of Vehicles and Designs 17 April 2011 Pages: 190 - 193

17. In memory of Professor Nikolai Vladimirovich Umnov (1936–2010)

    In Memoriam 17 April 2011 Pages: 194 - 194