1. Processes in melts of solid-phase reduction products of ilmenite concentrates

   • A. V. Asanov
   • V. E. Roshchin
   • A. V. Roshchin

   OriginalPaper 04 December 2010 Pages: 695 - 698

2. Capillary wicking of samples obtained by spraying wet iron ore to the pelletizer coating

   • V. M. Pavlovets

   OriginalPaper 04 December 2010 Pages: 699 - 702

3. Slab solidification

   • V. V. Stulov
   • V. I. Odinokov
   • I. V. Chistyakov

   OriginalPaper 04 December 2010 Pages: 703 - 705

4. Hardening of quenched structural steel on deformation

   • E. V. Kornet

   OriginalPaper 04 December 2010 Pages: 706 - 708

5. Heterophase structure in steel 20 after stepped quenching

   • V. M. Farber
   • V. P. Shveikin
   • A. S. Yurovskikh

   OriginalPaper 04 December 2010 Pages: 709 - 711

6. Recycling wastes in sinter and hot-metal production

   • V. A. Dolinskii
   • L. D. Nikitin
   • K. I. Domnin

   OriginalPaper 04 December 2010 Pages: 712 - 716

7. Influence of nanopowder modification of metal on the quality of continuous-cast bar

   • V. P. Komshukov
   • A. N. Cherepanov
   • L. A. Ganzer

   OriginalPaper 04 December 2010 Pages: 717 - 722

8. Formation of nanophases in electroexplosive alloying with aluminum and boron and electron-beam treatment of titanium surfaces

   • S. V. Karpii
   • M. M. Morozov
   • V. E. Gromov

   OriginalPaper 04 December 2010 Pages: 723 - 728

9. Increasing the cyclic life of submicrocrystalline and large-grain titanium in high-intensity ionic implantation

   • Yu. P. Sharkeev
   • V. A. Kukareko
   • A. S. Kuchina

   OriginalPaper 04 December 2010 Pages: 729 - 732

10. Smelting steel from semiprocessed carbon hot metal under magnesia slag in 160-t converters

    • A. A. Babenko
    • M. S. Fomichev
    • S. A. Remigo

    OriginalPaper 04 December 2010 Pages: 733 - 736

11. Hydrodynamics and optimization of bottom-tuyere parameters for steel injection in the intermediate ladle

    • B. S. Gonchar
    • E. F. Diyuk
    • V. V. Kislitsa

    OriginalPaper 04 December 2010 Pages: 737 - 740

12. Formation of iron-based melts and scope for improvement in steel properties

    • S. P. Burmasov
    • A. G. Gudov
    • L. A. Smirnov

    OriginalPaper 04 December 2010 Pages: 741 - 745

13. Influence of the pressure in the vacuum unit’s working chamber on the content of hydrogen and nonmetallic inclusions in steel

    • S. V. Terletskii
    • V. A. Matochkin
    • V. F. Sobolev

    OriginalPaper 04 December 2010 Pages: 746 - 749

14. Thermodynamic analysis of the reduction of titanium in Ti-O-C and Ti-O-C-Si systems

    • I. V. Ryabchikov
    • V. G. Mizin
    • A. Yu. Akhmadeev

    OriginalPaper 04 December 2010 Pages: 750 - 752

15. Stabilization of conditions in broad-strip mills to improve the transverse profile of hot-rolled strip

    • E. A. Garber
    • M. V. Khlopotin
    • R. B. Paligin

    OriginalPaper 04 December 2010 Pages: 753 - 758

16. Prospects for Russian production of strip employed in large-diameter electrowelded pipe

    • Yu. V. Konovalov

    OriginalPaper 04 December 2010 Pages: 759 - 765

17. Determining the adjustment of piercing mills with driven guide disks (Disher mills)

    • V. V. Mul’chin
    • A. V. Vydrin
    • A. V. Zinchenko

    OriginalPaper 04 December 2010 Pages: 766 - 768

18. Permissible deformation of wire blank with specified margin of strength

    • G. N. Gur’yanov

    OriginalPaper 04 December 2010 Pages: 769 - 772

19. Production of high-strength hot-galvanized sheet from dual-phase steel

    • V. A. Belousov
    • P. A. Petrenko
    • V. A. Tkachenko

    OriginalPaper 04 December 2010 Pages: 773 - 776

20. Design of coolant disks for the production of amorphous alloys

    • G. A. Srebryanskii
    • V. V. Belousov
    • P. Yu. Yurich

    OriginalPaper 04 December 2010 Pages: 777 - 780

21. Analysis of pipe production and consumption (2007–2010)

    • A. A. Brodov
    • L. A. Kondratov

    OriginalPaper 04 December 2010 Pages: 781 - 783