1. Oxygen-converter reduction of iron and manganese from their oxides by components dissolved in liquid iron

   • M. K. Shakirov
   • I. A. Zhibinova
   • E. V. Protopopov

   OriginalPaper 10 October 2009 Pages: 445 - 449

2. Calculation of gas-powder injection units using models of two-speed flow

   • E. V. Protopopov
   • T. R. Galiullin
   • P. S. Kharlashin

   OriginalPaper 10 October 2009 Pages: 450 - 453

3. Improving the rolling of rails

   • S. V. Dorofeev
   • V. V. Dorofeev
   • V. N. Peretyat’ko

   OriginalPaper 10 October 2009 Pages: 454 - 455

4. Deformable heatproof transeutectic silumin for pistons

   • A. N. Prudnikov

   OriginalPaper 10 October 2009 Pages: 456 - 459

5. Utilization of oxidized cast-iron and steel scrap in small-diameter shaft furnaces

   • A. V. Feoktistov
   • I. F. Selyanin
   • V. A. Marchenko

   OriginalPaper 10 October 2009 Pages: 460 - 462

6. Influence of the grain size of Fe-3.25% Si polycrystalline alloy on twinning over a broad range of temperature and strain rate

   • V. A. Fedorov
   • T. N. Pluzhnikova
   • D. E. Dolgikh

   OriginalPaper 10 October 2009 Pages: 463 - 465

7. Carbidization of titanium alloys in electroexplosive carburization and additional heat treatment

   • A. V. Vostretsova
   • S. V. Karpii
   • V. E. Gromov

   OriginalPaper 10 October 2009 Pages: 466 - 469

8. Coke quality for blast furnaces with coal-dust fuel

   • Yu. A. Zolotukhin
   • N. S. Andreichikov

   OriginalPaper 10 October 2009 Pages: 470 - 474

9. Coal gasification as an alternative to natural gas

   • A. I. Pavlov

   OriginalPaper 10 October 2009 Pages: 475 - 478

10. Blast-furnace charging with a lobed batch distributor

    • E. G. Donskov
    • V. P. Lyalyuk
    • E. E. Donskov

    OriginalPaper 10 October 2009 Pages: 479 - 485

11. Improving the continuous casting of rail steel

    • A. B. Yur’ev
    • L. A. Godik
    • N. M. Sapaev

    OriginalPaper 10 October 2009 Pages: 486 - 488

12. Automated dimensional monitoring of hot continuous-cast billet

    • A. V. Anikin
    • I. P. Ierusalimov
    • Yu. N. Karfidov

    OriginalPaper 10 October 2009 Pages: 489 - 490

13. Smelting pure IIIX15CΓ-B electrosteel with ferroalloy diversification

    • M. I. Gasik
    • A. I. Panchenko
    • S. L. Mazuruk

    OriginalPaper 10 October 2009 Pages: 491 - 494

14. Low-ash reducing agents in electrical heating of silicoaluminum

    • A. N. Glazatov
    • A. Yu. Baimakov
    • A. M. Saltykov

    OriginalPaper 10 October 2009 Pages: 495 - 497

15. Improvements to rolling on broad-strip mills

    • A. I. Starikov
    • A. G. Medvedev
    • K. A. Medvedev

    OriginalPaper 10 October 2009 Pages: 498 - 500

16. Effective production of large pipe blanks

    • O. A. Kobelev
    • A. V. Zinov’ev
    • M. A. Tsepin

    OriginalPaper 10 October 2009 Pages: 501 - 505

17. Mandrel calibration and optimization of deformation source in piercing mill

    • S. R. Rakhmanov
    • V. N. Danchenko

    OriginalPaper 10 October 2009 Pages: 506 - 509

18. Lubricants for dry wire drawing

    • A. A. Trukhanovich
    • A. A. Ledneva

    OriginalPaper 10 October 2009 Pages: 510 - 511

19. Drawplate manufacture using an electrospark cutting tool

    • A. B. Solyanikov
    • E. Yu. Prein
    • P. N. Smirnov

    OriginalPaper 10 October 2009 Pages: 512 - 515

20. Standardizing the annealing of metal rolled on reversible and four-cell mills in dome furnaces

    • T. P. Poletskova
    • Yu. P. Demidchenko
    • V. N. Gorbulin

    OriginalPaper 10 October 2009 Pages: 516 - 517

21. Improving the magnetic properties of 2NSR amorphous alloy

    • B. A. Kornienko
    • E. V. Artamonov

    OriginalPaper 10 October 2009 Pages: 518 - 520

22. Enrichment by X-ray radiometric separation

    • E. F. Tsypin
    • V. S. Shemyakin
    • E. V. Ental’tsev

    OriginalPaper 10 October 2009 Pages: 521 - 524