Oxygen-converter reduction of iron and manganese from their oxides by components dissolved in liquid iron M. K. ShakirovI. A. ZhibinovaE. V. Protopopov OriginalPaper 10 October 2009 Pages: 445 - 449
Calculation of gas-powder injection units using models of two-speed flow E. V. ProtopopovT. R. GaliullinP. S. Kharlashin OriginalPaper 10 October 2009 Pages: 450 - 453
Improving the rolling of rails S. V. DorofeevV. V. DorofeevV. N. Peretyat’ko OriginalPaper 10 October 2009 Pages: 454 - 455
Deformable heatproof transeutectic silumin for pistons A. N. Prudnikov OriginalPaper 10 October 2009 Pages: 456 - 459
Utilization of oxidized cast-iron and steel scrap in small-diameter shaft furnaces A. V. FeoktistovI. F. SelyaninV. A. Marchenko OriginalPaper 10 October 2009 Pages: 460 - 462
Influence of the grain size of Fe-3.25% Si polycrystalline alloy on twinning over a broad range of temperature and strain rate V. A. FedorovT. N. PluzhnikovaD. E. Dolgikh OriginalPaper 10 October 2009 Pages: 463 - 465
Carbidization of titanium alloys in electroexplosive carburization and additional heat treatment A. V. VostretsovaS. V. KarpiiV. E. Gromov OriginalPaper 10 October 2009 Pages: 466 - 469
Coke quality for blast furnaces with coal-dust fuel Yu. A. ZolotukhinN. S. Andreichikov OriginalPaper 10 October 2009 Pages: 470 - 474
Coal gasification as an alternative to natural gas A. I. Pavlov OriginalPaper 10 October 2009 Pages: 475 - 478
Blast-furnace charging with a lobed batch distributor E. G. DonskovV. P. LyalyukE. E. Donskov OriginalPaper 10 October 2009 Pages: 479 - 485
Improving the continuous casting of rail steel A. B. Yur’evL. A. GodikN. M. Sapaev OriginalPaper 10 October 2009 Pages: 486 - 488
Automated dimensional monitoring of hot continuous-cast billet A. V. AnikinI. P. IerusalimovYu. N. Karfidov OriginalPaper 10 October 2009 Pages: 489 - 490
Smelting pure IIIX15CΓ-B electrosteel with ferroalloy diversification M. I. GasikA. I. PanchenkoS. L. Mazuruk OriginalPaper 10 October 2009 Pages: 491 - 494
Low-ash reducing agents in electrical heating of silicoaluminum A. N. GlazatovA. Yu. BaimakovA. M. Saltykov OriginalPaper 10 October 2009 Pages: 495 - 497
Improvements to rolling on broad-strip mills A. I. StarikovA. G. MedvedevK. A. Medvedev OriginalPaper 10 October 2009 Pages: 498 - 500
Effective production of large pipe blanks O. A. KobelevA. V. Zinov’evM. A. Tsepin OriginalPaper 10 October 2009 Pages: 501 - 505
Mandrel calibration and optimization of deformation source in piercing mill S. R. RakhmanovV. N. Danchenko OriginalPaper 10 October 2009 Pages: 506 - 509
Lubricants for dry wire drawing A. A. TrukhanovichA. A. Ledneva OriginalPaper 10 October 2009 Pages: 510 - 511
Drawplate manufacture using an electrospark cutting tool A. B. SolyanikovE. Yu. PreinP. N. Smirnov OriginalPaper 10 October 2009 Pages: 512 - 515
Standardizing the annealing of metal rolled on reversible and four-cell mills in dome furnaces T. P. PoletskovaYu. P. DemidchenkoV. N. Gorbulin OriginalPaper 10 October 2009 Pages: 516 - 517
Improving the magnetic properties of 2NSR amorphous alloy B. A. KornienkoE. V. Artamonov OriginalPaper 10 October 2009 Pages: 518 - 520
Enrichment by X-ray radiometric separation E. F. TsypinV. S. ShemyakinE. V. Ental’tsev OriginalPaper 10 October 2009 Pages: 521 - 524