Technique of physical modeling of lightning strike effects on aircraft Z. M. GizatullinR. M. GizatullinM. G. Nuriev Flight Vehicle Design 20 October 2016 Pages: 157 - 160
Disk wing to main rotor conversion mechanics V. V. PavlovM. S. Gasilov Flight Vehicle Design 20 October 2016 Pages: 161 - 167
Fuzzy logic rule as a method for making a design decision in rocketry development V. G. ZezinM. I. Reshetnikov Structural Mechanics and Strength of Flight Vehicles 20 October 2016 Pages: 168 - 174
Control synthesis for an unmanned helicopter with time-delay under uncertain external disturbances V. I. GarkushenkoS. S. VinogradovG. N. Barakos Flight Dynamics and Control of Flight Vehicles 20 October 2016 Pages: 175 - 182
The aerospace vehicle control characterizing by considerable time delay A. V. EfremovM. S. TyaglikV. V. Aleksandrov Flight Dynamics and Control of Flight Vehicles 20 October 2016 Pages: 183 - 189
Collapse of a spheroidal cavitation bubble near a solid wall A. A. AganinM. A. Il’gamovV. G. Malakhov Aero- and Gas-Dynamics of Flight Vehicles and Their Engines 20 October 2016 Pages: 190 - 196
Joint effect of input asymmetrical velocity profile and initial turbulence intensity on hydraulics of a separated diffuser of GTE combustion chamber M. M. Gur’yanovaSh. A. Piralishvili Aero- and Gas-Dynamics of Flight Vehicles and Their Engines 20 October 2016 Pages: 197 - 205
Experimental investigation of lift for a wing-in-ground effect aircraft model D. V. NazarovV. A. FrolovV. G. Shakhov Aero- and Gas-Dynamics of Flight Vehicles and Their Engines 20 October 2016 Pages: 206 - 210
Wave resistance defect in a planar flow over periodic reliefs V. V. SemenovV. A. VolkovJ. S. S. Sidhu Aero- and Gas-Dynamics of Flight Vehicles and Their Engines 20 October 2016 Pages: 211 - 217
Experimental investigation of local heat transfer for complex-shaped surfaces using thermochromic liquid crystals I. N. BaibuzenkoA. A. SedlovV. L. Ivanov Aircraft and Rocket Engine Design and Development 20 October 2016 Pages: 218 - 223
An integrated system of operation mode synchronization for the helicopter powerplant engines A. P. Vel’dyaevV. N. EfanovA. A. Zaitseva Aircraft and Rocket Engine Design and Development 20 October 2016 Pages: 224 - 231
Fabrication of filters by a multielectrode tool V. P. SmolentsevS. V. SafonovYu. V. Sharov Aircraft and Rocket Engine Design and Development 20 October 2016 Pages: 232 - 236
Generalized surge line obtaining jointly with speed lines I. A. KrivosheevK. E. RozhkovN. B. Simonov Aircraft and Rocket Engine Theory 20 October 2016 Pages: 237 - 242
A simulator of the aircraft air data system E. S. Efremova Aircraft and Rocket Engine Theory 20 October 2016 Pages: 243 - 248
Relationship of flame propagation speed for methane–hydrogen fuel of the internal combustion engine with parameters of ion current and hydrogen concentration A. P. ShaikinI. R. Galiev Aircraft Instruments and Instrumentation Computer Complexes 20 October 2016 Pages: 249 - 253
Research of technological capacities of the process of long-length skin forming by combination of roll-bending and peen forming processing A. Yu. Malashchenko Aircraft Production Technology 20 October 2016 Pages: 254 - 258
Quantitative assessment of adhesive contact between carbon fiber and epoxy binding V. A. Nelyub Aircraft Production Technology 20 October 2016 Pages: 259 - 262
Structural optimization of the neural network model for the gas turbine engine monitoring S. V. Novikova Automation of Design and Production of Aeronautical Equipment 20 October 2016 Pages: 263 - 270
Seadrome: Increasing the safety of takeoff and landing operations in the seaplane basin V. Yu. Voloshchenko Radio Engineering and Communications 20 October 2016 Pages: 271 - 276
Study of thin-walled parts shaping process based on flanging and embossing E. G. Dem’yanenkoI. P. Popov Technical Notes Aircraft Production Technology 20 October 2016 Pages: 277 - 282
Radial two-stage microturbine for pneumatic actuation Yu. P. KuznetsovV. L. KhimichA. A. Krainov Aircraft Production Technology 20 October 2016 Pages: 283 - 286
Study of shaping strategies for blisk vane channels by a cup tool D. V. Kurylev Aircraft Production Technology 20 October 2016 Pages: 287 - 292
Approach to implementing hardware-independent automatic control systems of lathes and lathe-milling CNC machines G. M. MartinovR. A. NezhmetdinovA. U. Kuliev Aircraft Production Technology 20 October 2016 Pages: 293 - 296