Influence of the cutting edge rounding on the chip formation process: Part 1. Investigation of material flow, process forces, and cutting temperature B. DenkenaJ. KöhlerMesfin Sisay Mengesha Production Process 12 February 2012 Pages: 329 - 338
Development of a warm cross wedge rolling process using FEA and downsized experimental trials Hanns KacheMalte StonisBernd-Arno Behrens Production Process 24 April 2012 Pages: 339 - 348
A new experimental methodology to analyse the friction behaviour at the tool-chip interface in metal cutting Hendrik PulsFritz KlockeDieter Lung Production Process 08 May 2012 Pages: 349 - 354
Process design space for optimal surface integrity in finish hard milling of tool steel S. ZhangW. LiY. B. Guo Production Process 09 May 2012 Pages: 355 - 365
Residual stresses in surface layer after dry and MQL turning of AISI 316L steel Tadeusz LeppertRu Lin Peng Production Process Open access 23 May 2012 Pages: 367 - 374
Determination of surface and in-depth residual stress distributions induced by hard milling of H13 steel S. ZhangT. C. DingJ. F. Li Production Process 26 May 2012 Pages: 375 - 383
The non-hydrostatic response of polymer melts as a pressure medium in sheet metal forming A. E. TekkayaM. M. HussainJ. Witulski Production Process 03 June 2012 Pages: 385 - 394
Simulation of personnel requirements during production ramp-up Gisela LanzaAnna Sauer Production Process 07 June 2012 Pages: 395 - 402
Flank milling of compliant workpieces with chamfered tools B. DenkenaW. BickelV. Sellmeier Production Process 19 June 2012 Pages: 403 - 412
Shear cutting of press hardened steel: influence of punch chamfer on process forces, tool stresses and sheared edge qualities Katrin NothhaftJoungsik SuhWolfram Volk Production Process 19 July 2012 Pages: 413 - 420
Fatigue analysis of a mechanical press by means of the hybrid multi-body simulation B.-A. BehrensR. KrimmC. Wager Computer Aided Engineering 14 July 2012 Pages: 421 - 430
Research on tool wear detection based on machine vision in end milling process Jilin ZhangChen ZhangLaishui Zhou Computer Aided Engineering 22 June 2012 Pages: 431 - 437
Development of an innovative monitoring system for spray fields in hot forging processes Bernd-Arno BehrensConrad FrischkornIngo Lüken Quality Assurance 20 June 2012 Pages: 439 - 447
Model based logistic monitoring for supply and assembly processes Ben MünzbergMatthias SchmidtPeter Nyhuis Production Management 13 July 2012 Pages: 449 - 458
Tool path adaption based on optical measurement data for milling with industrial robots E. AbeleK. SchützerM. Pischan Machine Tool 18 May 2012 Pages: 459 - 465
Analysis of servo-mechanic drive concepts for forming presses Christer-C. SchenkeHajo WiemerKnut Großmann Machine Tool 30 May 2012 Pages: 467 - 474
Reliable material damping ratio determination in machine tool structures K. NiehuesS. SchwarzM. F. Zaeh Machine Tool 03 June 2012 Pages: 475 - 484
Process stabilization with an adaptronic spindle system Berend DenkenaOlaf Gümmer Machine Tool 19 June 2012 Pages: 485 - 492
Improvement of dry EDM process characteristics using artificial soft computing methodologies Reza TeimouriHamid Baseri Machine Tool 22 June 2012 Pages: 493 - 504
Identification method for damping parameters of roller linear guides Christian BrecherMarcel FeyStephan Bäumler Machine Tool 14 July 2012 Pages: 505 - 512
An active tool holding device Alexander BolderingAnnika Raatz Machine Tool 15 July 2012 Pages: 513 - 520
Eccentric universal joints for parallel kinematic machine tools: variants and kinematic transformations Knut GroßmannBernd Kauschinger Machine Tool 29 July 2012 Pages: 521 - 529
An agent-based concept for planning and control of the production of carbon fibre reinforced plastics aircraft structures with mobile production units Franz DietrichChristian LöchteAnnika Raatz Assembly 07 June 2012 Pages: 531 - 539