Volume 31, issue 3, March 2022
74 articles in this issue
-
-
-
Investigation on Hydrogen Embrittlement Sensitivity of Hot-Rolled and Annealed Microstructure to AISI 430 Ferritic Stainless Steel
Authors (first, second and last of 6)
-
Mechanism of Surface Hole Evolution and Impact on Corrosion Resistance of High-Strength Low-Alloy Weathering Steel
Authors (first, second and last of 5)
-
Evaluation of the Ferromagnetic Cold-Sprayed Coating Peeling Process at the Interface Based on Magnetic Barkhausen Noise Testing
Authors (first, second and last of 6)
-
Effect of Alternating Current and Cathodic Protection on Corrosion of X80 Steel in Alkaline Soil
Authors (first, second and last of 8)
-
-
Effect of Heat Treatments on Microstructure and Mechanical Properties of AlSi7Mg Fabricated by Selective Laser Melting
Authors (first, second and last of 4)
-
-
The Influence of Rotational Speed on Bonding Strength, Magnetic Properties, and Mechanical Properties of Fe3O4/ZrO2 Magnetic Composites
Authors (first, second and last of 4)
-
-
-
-
Microbiologically Influenced Corrosion of AA 6061 with Bacillus Species in an Environment Containing an Organic Nitrogen Source
Authors (first, second and last of 7)
-
Correction to: Microbiologically Influenced Corrosion of AA 6061 with Bacillus Species in an Environment Containing an Organic Nitrogen Source
Authors (first, second and last of 7)
-
The Assembly of Silicalite-1 Layer on Open Cell Aluminum Foam and Its Corrosion Resistance
Authors (first, second and last of 6)
-
Correction to: The Assembly of Silicalite-1 Layer on Open Cell Aluminum Foam and Its Corrosion Resistance
Authors (first, second and last of 6)
-
-
Surface and Structural Modifications of Tungsten by Laser Irradiation for Enhanced Electrochemical Corrosion Resistance
Authors (first, second and last of 8)
-
Structural Elucidation, Morphological Properties, and Dielectric Properties of Nickel-Substituted Cobalt and Lead-Based X-Type Hexagonal Ferrites
Authors (first, second and last of 9)
-
Compression Performance with Different Build Orientation of Fused Filament Fabrication Polylactic Acid, Acrylonitrile Butadiene Styrene, and Polyether Ether Ketone
Authors (first, second and last of 5)
-
Multi-parameter Optimization of Laser Cladding 15-5PH Using TOPSIS-GRA Based on Combined Weighting Method
Authors (first, second and last of 4)
-
Electrochemical Performance of Polyaniline Support on Electrochemical Activated Carbon Fiber
Authors
-
The Effects of Solidification Cooling and Growth Rates on Microstructure and Hardness of Supersaturated Al-7%Si-x%Zn Alloys
Authors (first, second and last of 4)
-
-
Effect of Ion Irradiation on Surface Microstructure and Nano-Hardness of SA508-IV Reactor Pressure Vessel Steel
Authors (first, second and last of 4)
-
Extrusion of Light and Ultralight Alloys with Liquid Nitrogen Conformal Cooled Dies: Process Analysis and Simulation
Authors (first, second and last of 5)
-
-
Process Optimization of Planetary Rolling of Bismuth-Containing Austenitic Stainless Steel
Authors (first, second and last of 5)
-
Applicability of Hill48 Yield Model and Effect of Anisotropic Parameter Determination Methods on Anisotropic Prediction
Authors (first, second and last of 5)
-
Influence of Nb Addition on Sliding Wear Behavior of 25 Cr 7 Ni Cast Austenitic-Ferritic Steel
Authors
-
The Influence of Polymeric Ester-Type Additives on the Performance of Metal Cutting Fluids for Machining of Titanium Alloy
Authors (first, second and last of 4)
-
Performance Analysis of Varying Tool Pin Profile on Friction Stir Welded 2050-T84Al-Cu-Li Alloy Plates
Authors (first, second and last of 5)
-
-
Stress Corrosion Susceptibility and Electrochemical Characteristic of X80 Under a Disbonded Coating in a Low-pH Soil Solution with Cathodic Protection
Authors (first, second and last of 8)
-
-
Investigation on Tribological Behavior of Hot-Pressed Steel/TiB2 Composites Using Taguchi Experimental Design
Authors (first, second and last of 8)
-
-
Performance of Vibration-Assisted Laser Welded Joints Based on Orthogonal Experiment Design
Authors (first, second and last of 6)
-
Effect of Anisotropy on the Manufacturing Process of Mg-Zn-Zr Alloy Connecting Rod
Authors (first, second and last of 5)
-
Effects of Rolling Deformation on Microstructure, Tensile Properties and Corrosion Behaviors of High Mg Alloyed of Al-Mg Alloy
Authors (first, second and last of 6)
-
-
-
Effect of Laser Spot Size, Scanning Strategy, Scanning Speed, and Laser Power on Microstructure and Mechanical Behavior of 316L Stainless Steel Fabricated via Selective Laser Melting
Authors (first, second and last of 5)
-
-
Statistical Analysis of Laser-Welded Blanks in Deep Drawing Process: Response Surface Modeling
Authors (first, second and last of 7)
-
Optimizing Process Parameters of As-Homogenized Mg-Gd-Y-Zn-Zr Alloy in Isothermal Uniaxial Compression on the Basis of Processing Maps via Prasad Criterion and Murty Criterion
Authors (first, second and last of 7)
-
Application of Numerical Simulation and Physical Modeling for Verifying a Cold Forging Process for Rotary Sleeves
Authors (first, second and last of 4)
-
Study on the Variation in Mechanical Properties along the Dissimilar Weldments of P22 and P91 Steel
Authors (first, second and last of 5)
-
Microstructural and Corrosion Resistance Evaluation of Hot-Dipped Al-Zn-Si Alloy-Coated Steel
Authors
