Effect of a cyclic hold on the ductility and strength of 45 steel in the complex stressed state at low temperatures B. I. Koval'chukN. M. Kul'chitskiiA. A. Lebedev Scientific-Technical Section Pages: 1027 - 1031
Mathematical model of the thermomechanical bending of rolled sheets A. L. KvitkaA. S. TsybenkoN. G. Vashchenko Scientific-Technical Section Pages: 1032 - 1038
Load-carrying capacity of reinforced plastic pipes sealed with a film G. P. ZaitsevV. N. Sud'in Scientific-Technical Section Pages: 1039 - 1044
Thermal stress state of hollow cylinders during unilateral internal heating G. N. Tret'yachenkoB. S. KarpinosL. E. Kiyashko Scientific-Technical Section Pages: 1045 - 1048
Inverse problem of the distribution of material in disks from the condition of strength V. P. MalkovE. A. Salganskaya Scientific-Technical Section Pages: 1049 - 1054
Solution by method of finite elements of three-dimensional noncoupled thermoelasticity problem for bodies of revolution S. D. BobritskayaI. A. Klimenko Scientific-Technical Section Pages: 1055 - 1061
Stress-strain state of freely supported three-ply trapezoidal plates A. V. VestyakE. A. Khvilon Scientific-Technical Section Pages: 1062 - 1068
Dependence of the radiation-induced decrease in the durability of refractory steel on the neutron parameters V. N. KiselevskiiB. D. Kosov Scientific-Technical Section Pages: 1068 - 1072
Creep in alloy VT5-1 with protective enamel coatings in air É. S. UmanskiiV. M. TovtO. V. Tsygulev Scientific-Technical Section Pages: 1072 - 1074
Temperature-time relation in structural strengthening of D16 alloy under creep conditions N. A. Vorob'evÉ. N. Bich Scientific-Technical Section Pages: 1075 - 1077
Low-cycle endurance of clad steel in a corrosive environment A. B. KuslitskiiI. V. KokotailoI. A. Sitnikova Scientific-Technical Section Pages: 1078 - 1080
Fatigue resistance of thin sheet D16AT and AMg6M alloys in the linear and plane stressed state under high-frequency loading conditions R. I. Stefanov Scientific-Technical Section Pages: 1081 - 1083
Effect of surface layer quality on the low-cycle endurance of structural steels in working environments I. P. PistunA. B. Kuslitskii Scientific-Technical Section Pages: 1084 - 1087
Stabilization of a crack trajectory with thermoelastic fields V. M. Finkel'V. E. SeredaG. B. Rodyukov Scientific-Technical Section Pages: 1087 - 1091
Crystallography of cleavage in BCC metals A. Ya. KrasovskiiV. A. Vainshtok Scientific-Technical Section Pages: 1091 - 1099
Determining the temperature of stopping of a brittle crack on the basis of series of impact bending tests Yu. S. TomenkoA. A. PashchenkoI. N. Khristenko Scientific-Technical Section Pages: 1099 - 1102
Determining the conditions of quasibrittle failure of constructional metals which are ductile at cryogenic temperatures N. V. NovikovO. Ya. Znachkovskii Scientific-Technical Section Pages: 1102 - 1106
Comparison of two numerical methods of calculating coefficients of stress intensity V. A. Vainshtok Scientific-Technical Section Pages: 1106 - 1110
Time dependence of strength of bodies in cleavage V. I. RomanchenkoG. V. Stepanov Scientific-Technical Section Pages: 1110 - 1114
Finite-elements-method investigation of the stressed-deformed state of a clamp model in the zone of structural concentrators A. L. KvitkaP. P. VoroshkoS. D. Bobritskaya Scientific-Technical Section Pages: 1114 - 1117
Effect of the boride sublayer in silicide coatings on the mechanical properties of molybdenum at high temperatures N. I. PolyakovO. V. TsygulevV. I. Zmii Scientific-Technical Section Pages: 1118 - 1121
Effect of temperature on the mechanical properties of steels 35KhMA and 12KhMA V. G. ShiyanV. M. L'vovskii Scientific-Technical Section Pages: 1121 - 1123
Mechanical properties of certain metals in impact tension in the 20–500°C temperature range A. P. Vashchenko Scientific-Technical Section Pages: 1124 - 1126
Effect of diamond and other finishing methods on the structure and mechanical properties of a hard alloy Yu. P. Linenko-Met'nikovYu. I. SozinL. I. Aleksandrova Scientific-Technical Section Pages: 1127 - 1130
Exciting forces during hydrodynamic interaction in networks of thin profiles and a potential flow V. É. SarenV. A. Yudin Production Section Pages: 1130 - 1135
Single-frequency modes of a frictional autooscillatory system with two degrees of freedom taking into consideration imperfect elasticity of the material B. M. Zhirnov Production Section Pages: 1136 - 1140
Effect of certain features of heat dissipation in overloading on the life of medium carbon steel Yu. I. RyzhakovL. N. Molchanov Production Section Pages: 1140 - 1146
Unit for investigating deformation of materials by tension at different temperatures E. A. Sukhodol'skayaB. P. TaranM. S. Bresler Production Section Pages: 1147 - 1149
Method of investigating the supporting capacity of materials with protective coatings B. A. LyashenkoV. V. RishinO. V. Tsygulev Production Section Pages: 1149 - 1152