Microstructure Variation of Ultrasuper Critical 11Cr Ferritic Steel Under Long-Term Thermal Ageing and Creep C. S. Kim SCIENTIFIC AND TECHNICAL SECTION 14 November 2019 Pages: 501 - 507
Elastoplastic Assessment of Limiting Internal Pressure in Thick-Walled Cylinders with Different Tension-Compressive Response S. WangQ. ZhuY. J. Jiang OriginalPaper 16 November 2019 Pages: 508 - 519
Simulation of Impact Fracture Behavior of Laminated Glass Based on DEM/FEM and Cohesive Model Z. G. YangM. Y. ZangY. L. Cheng OriginalPaper 14 November 2019 Pages: 520 - 533
Effect of the Eutectic Phase on the Microstructure and Tensile Strength of an Al–Zn–Ni–Mg–Cu Casting Aluminum Alloy D. H. ChenZ. ChenX. L. Hong OriginalPaper 16 November 2019 Pages: 534 - 540
Shear Fracture Model of Ultrasonic Cutting for an Aramid Paper Honeycomb X. Y. LiX. P. HuX. Wu OriginalPaper 14 November 2019 Pages: 541 - 547
Effect of Heat Treatment on the Microstructure and Strength of Stainless Steel-Clad Plate H. R. JinC. X. DuanY. L. Yi OriginalPaper 14 November 2019 Pages: 548 - 557
A Novel Inclined Excitation Method for Crack Detection of Non-Ferromagnetic Materials Using Eddy Current Thermography Z. W. YangH. P. YanW. Zhang OriginalPaper 18 November 2019 Pages: 558 - 568
Assessment of Cold Extrusion Effect on Stress–Strain Curves of Pure Copper Arc Parts Based on the Cosine Velocity Model S. H. HuangY. WuD. Y. Shu OriginalPaper 16 November 2019 Pages: 569 - 577
Fatigue Life Prediction of the Gear Box in Tracked Vehicles Based on Running Simulation Tests X. J. DuS. R. ZhangY. H. Zhang OriginalPaper 21 November 2019 Pages: 578 - 586
Tensile Fracture Behavior of Carbon Fiber/Al Composites Produced by the Liquid Extrusion Infiltration Technique Y. Q. Ma OriginalPaper 16 November 2019 Pages: 587 - 592
Residual Stresses in Ultrasonic-Assisted Laser Sintered Grinding Diamond Materials Z. B. YangY. Q. ZhangB. Zhao OriginalPaper 18 November 2019 Pages: 593 - 600
Microstructure and Microwave Absorption Properties of Cement-Based Material Reinforced with Reduced Graphene Oxide and Nanoparticles Y. F. SunT. S. ZhouY. Xun OriginalPaper 21 November 2019 Pages: 601 - 608
Effect of Zn on the Mechanical Properties and Microstructure of as-Cast and Solution-Treated Mg–6Y–2Nd–1Gd–0.5Zr Alloys J. Q. TaoS. H. HuangM. Li OriginalPaper 18 November 2019 Pages: 609 - 615
Density Effect of PTFE-Copper Powder Metallurgy Liner Material on the Perforation Performance of Shaped Charge Jets Y. J. XuZ. J. WangY. X. Jin OriginalPaper 16 November 2019 Pages: 616 - 623
Effect of Drilling-Induced Delamination on Buckling Behavior of Open Hole Composite Laminate Specimens Under Compressive Loading Q. F. DuanS. X. LiH. X. Hu OriginalPaper 16 November 2019 Pages: 624 - 632
Thermoelastic Stress-Strain Analysis of the Meshing Pairs of a Two-Tooth Difference Swing-Rod Movable Toothed Drive Y. L. YiY. F. GaoH. R. Jin OriginalPaper 21 November 2019 Pages: 633 - 645
Stress Corrosion of Bridge Cable Wire by the Response Surface Method C. Q. MiaoM. L. ZhuangB. Dong OriginalPaper 14 November 2019 Pages: 646 - 652
Rebar Corrosion Rate Estimation of Reinforced Concrete Components Exposed to Marine Environment Q. L. WuH. F. Yu OriginalPaper 16 November 2019 Pages: 653 - 659
Acidic-Thermal Ageing Effect on Compression Stress Relaxation of Silicone Rubber G. LiJ. M. GongX. J. Lu OriginalPaper 14 November 2019 Pages: 660 - 666
Stress-Strain and form Accuracy of Carbon Steel Components Produced by a Multi-Point Stretch Forming Technique J. XingY. Y. ChengZ. Yi OriginalPaper 19 November 2019 Pages: 667 - 677
Effect of Sampling Interval and Anisotropy on Laser Scanning Accuracy in Rock Material Surface Roughness Measurements S. M. HuL. HuangZ. Liu OriginalPaper 18 November 2019 Pages: 678 - 687
Correction to: Comparative Analysis of Processing Techniques’ Effect on the Strength of Carbon Black (N220)-Filled Poly(Lactic Acid) Composites A. V. RaneK. KannyS. Thomas Correction 21 November 2019 Pages: 688 - 688