Description of a mechanical hysteresis loop V. V. Matveev Scientific and Technical Section Pages: 901 - 908
The problem concerned with the critical dimension of the plastic zone at the tip of a crack in a quasibrittle fracture of metals A. Ya. KrasovskiiG. N. Nadezhdin Scientific and Technical Section Pages: 909 - 913
Study of the initial stage in crack development during the expansion and compression of specimens of poly(methyl methacrylate) P. A. PavlovS. Zhunisbekov Scientific and Technical Section Pages: 914 - 918
Sensitivity of materials to stress concentration under cyclic loading E. G. Makarov Scientific and Technical Section Pages: 919 - 923
Limiting equilibrium of cylindrical shells of ideal rigid-plastic material with different yield points in tension and compression O. N. ShabliiM. S. Mikhalishin Scientific and Technical Section Pages: 924 - 931
Study of the long-term strength and fatigue properties of polyurethane films A. M. KadyshevV. V. Khil'ehevskiiV. U. Ivchenko Scientific and Technical Section Pages: 932 - 935
Recovery processes during creep in molybdenum and its alloys O. I. MarusiiE. É. Zasimchuk Scientific and Technical Section Pages: 936 - 939
Estimation of the impact strength of steels at cryogenic temperatures D. V. LebedevG. A. Gadzhibalaev Scientific and Technical Section Pages: 940 - 944
Influence of electrolytic polishing on notch sensitivity of certain alloys in fatigue A. F. Getman Scientific and Technical Section Pages: 945 - 951
Effect of neutron irradiation on the mechanical properties and on the effect of programmed loading of titanium I. A. GindinÉ. S. LapiashviliI. M. Neklyudov Scientific and Technical Section Pages: 952 - 955
Effect of dislocation density and aging on the yield stress of Al-Cu-Mg-Mn alloys Yu. M. VainblatL. B. BerS. S. Khayurov Scientific and Technical Section Pages: 956 - 959
A dynamic method of arresting cracks V. M. Finkel'Yu. A. BrusentsovV. A. Dobkevich Scientific and Technical Section Pages: 960 - 963
Effct of mode of loading on the high-temperature creep of zirconium carbide P. V. ZubarevL. N. Dement'ev Scientific and Technical Section Pages: 964 - 967
Influence of heat treatment and surface finish of steel ÉI961 on its endurance V. K. YatsenkoE. Ya. KorenevskiiL. I. Ivshchenko Scientific and Technical Section Pages: 968 - 974
Ultrasonic nondestructive measurements of residual stresses O. I. GushchaV. K. LebedevF. G. Makhort Scientific and Technical Section Pages: 975 - 977
Effect of tempering temperature on resistance to crack propagation in steel 18Kh2N4VA V. G. MartynovM. A. Kramarov Scientific and Technical Section Pages: 978 - 980
Effect of deformation on the strength and plasticity of dilute chromium alloys A. N. RakitskiiV. G. TkachenkoV. I. Trefilov Scientific and Technical Section Pages: 981 - 984
Improvement of the profiles of root connections with the collars of turbine blades Ch. G. MustafinV. V. Nekrasov Industrial Section Pages: 985 - 988
Error in measuring strain by wire resistance strain gages due to the effect of unsteady heating A. N. Ser'eznovG. A. Tsareva Industrial Section Pages: 989 - 991
Plastic torsion of prismatic bars with a thin outer hardened layer B. A. ObodovskiiG. V. ArtyukhV. Z. Mazai Industrial Section Pages: 992 - 994
Time dependence of the strength of a cellular plastic I. G. RomanenkovV. A. Ivanov Industrial Section Pages: 995 - 997
Change in physicomechanical properties during aging of martensite-aging steels V. M. KondratovB. I. Krasnov Industrial Section Pages: 998 - 1001
A study of the initial stage of the thermal-fatigue failure of cast iron A. A. ZhukovB. M. Drapkin Industrial Section Pages: 1002 - 1006
Low-temperature strength of thermally hardened rolled rounds K. F. StarodubovYu. P. Gul'A. S. Gule vskii Industrial Section Pages: 1007 - 1011
Long duration strength and creep measurements on glass reinforced plastic tubes and shells N. G. TsoiA. V. Kolesnikov Industrial Section Pages: 1012 - 1014
Some characteristic cases of brittle fracture of welded constructions G. V. ZhemchuzhnikovV. V. Pavlov Industrial Section Pages: 1015 - 1018
Investigation into the cyclic strength of “45” and “40Kh” steels under the combined action of cyclic bending and static torsion E. K. PochtennyiE. S. Staichenko Industrial Section Pages: 1019 - 1022
Determination of the temperature fields of turbine disks and blades by irradiated diamond indicators E. F. BarbashinK. S. Pul'kisV. A. Nikolaenko Industrial Section Pages: 1023 - 1026
Testing of composite materials on annular specimens I. M. Kop'evV. N. GeminovA. S. Ovchinskii Brief Communications Pages: 1027 - 1029