A study of the accumulation of fatigue damage in relation to the conditions of service load É. Ya. FilatovV. É. PavlovskiiYu. A. Panfilov OriginalPaper Pages: 252 - 256
Effect of main machining operations on the surface finish and fatigue life of compressor blades made from 1Kh17N2 steel E. Ya. KorenevskiiV. K. Yatsenko OriginalPaper Pages: 257 - 262
Application of the deformation theory of fatigue to test conditions at stresses less than the elastic limit L. B. Getsov OriginalPaper Pages: 263 - 266
Use of fractography for studying the kinetics of failure of light alloys T. A. GordeevaI. P. ZheginaT. A. Volodina OriginalPaper Pages: 267 - 271
Constructing a theory for the strength of unidirectionally reinforced materials in compression A. N. Guz' BriefCommunication Pages: 278 - 280
Elastic properties of compact bone as an anisotropic material A. A. Uten'kinA. A. Sveshnikova OriginalPaper Pages: 281 - 285
Poinsson's ratio for carbon steel and gray iron at normal and low temperatures A. A. LebedevB. I. Koval'chukV. P. Lamashevskii OriginalPaper Pages: 292 - 297
The mechanical properties and failure of mild steel in tension A. Ya. KrasovskiiV. A. StepanenkoA. G. Voinitskii OriginalPaper Pages: 298 - 303
Influence of microadditives of Li, La, P, and B on the strength and plasticity of copper M. A. KrishtalM. A. VyboishchikA. L. Zolotoi OriginalPaper Pages: 304 - 307
The effect of temperature and deformation rate on the flow stress of erbium L. D. SokolovV. M. SolenovV. A. Skudnov OriginalPaper Pages: 308 - 311
Load bearing capacity of rotating shells made from rigid-viscoplastic reinforced materials O. N. Shablii OriginalPaper Pages: 312 - 319
One method of solving problems on cracking and stamping in the moment theory of elasticity V. Z. PartonB. A. Kudryavtsev OriginalPaper Pages: 320 - 324
Stresses and strains in an elastic inclined shell of constant torsion with stable heating of its edges B. A. GushchinV. M. Rassudov OriginalPaper Pages: 325 - 329
Fatigue strength of the material used for large hollow and solid shafts V. A. MasolI. V. KudryavtsevN. M. Savvina Industrial Section Pages: 330 - 334
The UIT-1200/50 device for determining the heat resistance of sealing materials N. L. GolegoM. E. BelitskiiA. P. Voidenov Industrial Section Pages: 335 - 339
Investigation of the strength of corrugated expansion pieces for low cyclic loading A. P. GusenkovN. N. Velichkin Industrial Section Pages: 340 - 345
Calculation of the strength of the force elements in gas-detonation presses G. V. StepanovV. G. PetushkovB. Ya. Maksimov Industrial Section Pages: 346 - 349
An apparatus for investigating material properties under explosive loading N. A. FotV. V. Yarosh Industrial Section Pages: 350 - 352
Quantitative appraisal of impairability of a material under cyclic loading I. M. VasinyukI. S. Sulik Brief Communications Pages: 353 - 354
Setup for the fatigue testing of sheet materials subjected to pure bending V. A. SamginI. A. Troyan Brief Communications Pages: 355 - 357
Effect of a high vacuum on the deformation of copper and aluminum A. V. AshukinA. A. GuslyakovI. M. Lyubarskii Brief Communications Pages: 358 - 360
The problem of the effect of diffusional chromizing and vanadizing on the fatigue strength of steel V. I. PokhmurskiiV. B. DalisovV. I. Didoshak Brief Communications Pages: 361 - 362
Recording the displacement of a surface under a pulsed load by a photomicrographic method G. V. Stepanov Brief Communications Pages: 363 - 364
Investigation of the deformation of aluminum by the etch-pit method E. Ya. Yakovlev Brief Communications Pages: 365 - 367
The influence of metallic coatings on the fatigue limit of VD17 aluminum alloy P. A. AverchenkoB. A. TreskunovV. M. Pleskach Brief Communications Pages: 368 - 369