1. The long time strength and creep of heat resistant materials with a programmed change in temperature

   • N. S. Mozharovskii
   • E. A. Antipov

   Scientific and Technical Section Pages: 1261 - 1267

2. Study of the deformation process in low-cycle loading

   • A. N. Romanov
   • M. M. Gadenin

   Scientific and Technical Section Pages: 1268 - 1273

3. Change in the fracture strength of structural steels under the influence of cyclic stresses

   • V. S. Girenko
   • V. A. Deinega
   • A. M. Khololeev

   Scientific and Technical Section Pages: 1274 - 1280

4. The question of the conditions of plasticity and brittle fracture of metals

   • N. I. Volkov

   Scientific and Technical Section Pages: 1281 - 1285

5. Structure and properties of 1Kh18N9T austenitic steel after program loading

   • I. A. Gindin
   • I. M. Neklyudov
   • M. P. Starolat

   Scientific and Technical Section Pages: 1286 - 1289

6. A thermodynamic theory of the mechanical strength and failure of a solid body

   • V. V. Fedorov

   Scientific and Technical Section Pages: 1290 - 1293

7. Stability of a structure consisting of two concentric rings connected by radial stays, under uniformly distributed load

   • Yu. D. Korablev

   Scientific and Technical Section Pages: 1294 - 1297

8. Velocity dependence of the discreteness of slip and the hardening parameters in aluminum at low temperatures

   • D. A. Didenko
   • V. V. Pustovalov

   Scientific and Technical Section Pages: 1298 - 1304

9. Change in fatigue limit of some light alloys on cooling from room temperature to −269°C

   • L. P. Andreev
   • N. V. Novikov

   Scientific and Technical Section Pages: 1305 - 1307

10. Influence of processing technology on the durability of sheets of the titanium alloy OT 4-1

    • V. A. Samgin
    • I. A. Troyan
    • V. N. Semirog-Orlik

    Scientific and Technical Section Pages: 1308 - 1312

11. Dependence of the mechanical properties of alloys of titanium with vanadium and aluminum on the oxygen content

    • Yu. A. Maksimov
    • I. I. Kornilov
    • S. D. Zagrebenyuk

    Scientific and Technical Section Pages: 1313 - 1315

12. Features of the deformation and failure of 1Kh18N9T steel on thermocyclic loading in relation to the time for which the material is held at the maximum temperature

    • N. S. Mozharovskii

    Scientific and Technical Section Pages: 1316 - 1319

13. Dependence of the yield stress of metals on grain size

    • S. G. Tresvyatskii

    Scientific and Technical Section Pages: 1320 - 1323

14. The nature of dislocation motion in KC1 crystals

    • V. A. Makara
    • N. N. Novikov
    • S. V. Mnyshenko

    Scientific and Technical Section Pages: 1324 - 1327

15. Investigation of the structure of the material of gas-turbine blades made of ZhS6KP alloy

    • G. P. Pimenova

    Scientific and Technical Section Pages: 1328 - 1333

16. High-strength carbon materials (survey)

    • L. A. Plutalova
    • G. B. Skripchenko

    Scientific and Technical Section Pages: 1334 - 1338

17. Creep and recovery of plasticized polyvinylchloride under biaxial tension

    • S. S. Veremchuk
    • É. S. Umanskii

    Scientific and Technical Section Pages: 1339 - 1343

18. Evaluation of softening of plastics during one-sided heating

    • E. G. Kuzovkov
    • V. S. Dvernyakov
    • V. V. Pasichnyi

    Scientific and Technical Section Pages: 1344 - 1350

19. The strength of nickel reinforced with tungsten fibers

    • V. N. Golovin
    • N. D. Rybal'chenko
    • A. S. Tron'

    Scientific and Technical Section Pages: 1351 - 1354

20. The compressive strength of copper reinforced with tungsten fiber

    • M. L. Gorb
    • B. A. Marek
    • O. K. Teodorovich

    Scientific and Technical Section Pages: 1355 - 1357

21. Search for lightest rod-type carrier system by the dynamic programming method

    • V. Ya. Mikhailishchev

    Scientific and Technical Section Pages: 1358 - 1361

22. Differing tendencies to brittle failure of various heats of 40Kh steel

    • S. M. Baranov
    • G. A. Vorob'eva
    • S. I. Karatushin

    Production Section Pages: 1362 - 1365

23. Investigation of damped oscillations of structural components in flowing water

    • A. A. Kaminer
    • B. M. Kavitskii

    Production Section Pages: 1366 - 1368

24. Experimental investigation of the stress in circular rings

    • I. P. Vlasenko
    • V. A. Potichenko

    Production Section Pages: 1369 - 1372

25. The RMA-5 automatic tester

    • M. A. Merman
    • B. V. Titov

    Production Section Pages: 1373 - 1375

26. A method of determining fracture toughness using the results of long time strength testing

    • V. I. Gladshtein
    • M. F. Sheshenev

    Brief Communications Pages: 1376 - 1377

27. Young's modulus of molybdenum sheet

    • Ya. M. Vitorskii
    • L. S. Igolkina
    • V. G. Tkachenko

    Brief Communications Pages: 1378 - 1380