Using the method of boundary integral equations for the numerical solution of volume problems of nonlinear fracture mechanics N. A. MakhutovV. A. PetushkovV. I. Zysin Scientific-Technical Section Pages: 833 - 841
Stable crack growth in an elastoplastic material I. M. Lavit Scientific-Technical Section Pages: 854 - 860
Fatigue resistance of aluminum and magnesium alloys at high loading frequencies L. E. MatokhnyukA. V. VoinalovichA. V. Kirillova Scientific-Technical Section Pages: 861 - 867
Determination of fatigue damage to nickel by the Barkhausen effect method A. I. Kovalev Scientific-Technical Section Pages: 867 - 871
Kinetics and fractography of fatigue fracture of val15 alloy at varying cycle asymmetry G. V. KlevtsovN. S. PostnikovZh. T. Bakirov Scientific-Technical Section Pages: 871 - 875
Feasibility of constructing equations of the mechanics of plasticity on the basis of general principles V. A. LikhachevV. G. Malinin Scientific-Technical Section Pages: 875 - 881
Probability evaluation for exhaustion of the operating capacity of gas-turbine-engine disks with low-cycle fatigue T. V. Balepina Scientific-Technical Section Pages: 881 - 885
Features of low-temperature deformation and hardening of Cu−Nb bimetal components V. A. LototskayaV. Ya. Il'ichev Scientific-Technical Section Pages: 885 - 889
Comparative analysis of the effect of plastic deformation on the microscopic elastic limit for copper and nickel T. T. Mogil'nikovaT. A. MolodkinaB. A. Movchan Scientific-Technical Section Pages: 890 - 893
Reversible effect of memory of form as the result of thermal cycling conditioning under load S. P. BelyaevS. L. Kuz'minV. A. Likhachev Scientific-Technical Section Pages: 894 - 899
Determination of the strength of silicon carbide in axial compression and bending after chemical treatment and application of hard coatings V. A. BushlovO. B. DashevskayaG. M. Okhrimenko Scientific-Technical Section Pages: 900 - 905
Dynamic compression of porous iron in plane shock waves with intensities up to 7 GPa G. V. StepanovV. I. ZubovA. I. Dzyubenko Scientific-Technical Section Pages: 905 - 910
Resistance of 12Kh18N10T and A-43UP corrosion-resistant steels to plastic deformation at different strain rates N. N. PopovV. N. PozdovL. V. Polyakov Scientific-Technical Section Pages: 910 - 915
Influence of preliminary deformation and the production factor on the spalling strength of 12Kh18N10T steel V. A. OgorodnikovE. S. Tyun'kinA. G. Ivanov Scientific-Technical Section Pages: 915 - 918
Stress waves in an orthotropic cylinder under local shock loading Yu. N. Babich Scientific-Technical Section Pages: 918 - 924
Strain-hardening during the glancing high-speed collision of plates M. A. MogilevskiiT. O. SanchaaYu. D. Shishkin Scientific-Technical Section Pages: 924 - 928
Stress-strain state of a rod-type piezoceramic sensor I. E. Gordienko Scientific-Technical Section Pages: 928 - 932
Analysis of methods of determining the damping capacity of a material under two-frequency loading V. V. MatveevA. P. Bovsunovskii Scientific-Technical Section Pages: 933 - 940
A nonlinear finite-element calculation on elastomer vibration absorbers for vibrational loading devices V. V. KirichevskiiN. N. Shilan Scientific-Technical Section Pages: 941 - 950
Numerical method of solving a contact problem of the theory of elasticity and the theory of thermal stresses. Report No. 1. Formulation of the problem and the method of solution V. I. Zaitsev Scientific-Technical Section Pages: 950 - 957
Algorithm for calculating the strength of discretely reinforced conical shells V. V. KabanovT. E. Levitskaya Scientific-Technical Section Pages: 958 - 963
Effect of the scale factor during the cyclic torsion of spring wire L. S. AndreevO. V. Potudin Industrial Section Pages: 964 - 967
Residual stresses in extruded bars formed from high-strength structural steel E. V. PolyakovV. V. Davydov Industrial Section Pages: 967 - 971
Laser diffractometry of the surface of fatigue fractures under applied cyclic loads A. V. MatokhinV. V. YudinA. V. Khlamenok Industrial Section Pages: 972 - 976