Possibility of a phenomenological description of the initial portions of creep of radiation irradiated aging alloys V. N. KiselevskiiV. V. Kovalev Scientific-Technical Section Pages: 765 - 770
Influence of cyclic overloads on the stress-rupture strength of an alloy for gas-turbine engine disks E. R. GolubovskiiG. P. Mel'nikovL. P. Sorokina Scientific-Technical Section Pages: 773 - 779
Mathematical description of transient creep É. I. Blinov Scientific-Technical Section Pages: 779 - 784
High-temperature creep of corundum refractories with anisotropic strain-hardening V. S. Romas'ko Scientific-Technical Section Pages: 784 - 788
Method of R-functions in problems on the nonsteady vibration of plates V. L. RvachevL. V. KurpaA. N. Shevchenko Scientific-Technical Section Pages: 789 - 793
Vibration damping in coupled discrete-continuous systems V. S. Didkovskii Scientific-Technical Section Pages: 794 - 797
Vibrations of an elastic two-layer plate V. S. DidkovskiiT. A. StarovoitovaÉ. I. Starovoitov Scientific-Technical Section Pages: 797 - 802
Effect of loading rate on the fracture toughness of quenched steel G. V. StepanovV. A. Makovei Scientific-Technical Section Pages: 802 - 806
Closure of a centeral crack in a circular disk under the influence of a temperature field V. D. Belen'kii Scientific-Technical Section Pages: 806 - 810
Evaluating the fracture toughness of thin-walled structures A. M. Dotsenko Scientific-Technical Section Pages: 811 - 818
Methodological problems in studying the fracture toughness of tungsten. Report No. 1 A. V. BabakE. I. Uskov Scientific-Technical Section Pages: 818 - 824
Kinetics of spall fracture of two steels V. I. RomanchenkoO. I. MarusiiM. A. Pokrovskii Scientific-Technical Section Pages: 824 - 830
Modulus of additional loading in the break of the loading path Yu. I. KadashevichA. N. Mikhailov Scientific-Technical Section Pages: 830 - 831
Determination of residual stresses in piecewise-inhomogeneous cylinders D. A. Ignat'kov Scientific-Technical Section Pages: 832 - 837
Solution of equations of the finite-element method for problems of mechanical interaction of deformed solids V. I. ZaitsevV. M. Shchavelin Scientific-Technical Section Pages: 837 - 842
Mechanical properties of metals in the range of small amounts of elastoplastic deformation Yu. D. SkripnikA. F. Voitenko Scientific-Technical Section Pages: 843 - 849
Calculation of the effect of stress concentration factor with multicycle fatigue G. M. Khazhinskii Scientific-Technical Section Pages: 849 - 854
Evaluation of the fatigue properties of high-temperature materials. Communication 2. Determination of fatigue limit for high-temperature alloys over a wide temperature range A. D. PogrebnyakA. V. Zheldubovskii Scientific-Technical Section Pages: 854 - 858
Effect of matrix type and form of stress state on mechanical properties of high-strength cast iron V. P. LamashevskiiI. V. MakovetskiiV. I. Litovka Scientific-Technical Section Pages: 858 - 862
Ability of the composite 50 Ti-47 Ni-3 Cu to transform heat energy into mechanical work upon cyclic temperature change S. P. BelyaevS. L. Kuz'minV. A. Likhachev Scientific-Technical Section Pages: 863 - 866
Crystallographic direction of brittle transcrystalline cleavage in the ferrite of low-carbon low-alloy steels V. M. GoritskiiD. P. Khromov Scientific-Technical Section Pages: 867 - 869
Mechanical properties of zirconium, titanium, and yttrium hydride alloys A. G. LaninI. M. ZalivinE. B. Boiko Scientific-Technical Section Pages: 869 - 876
Results of a study of the resistance to deformation and stress-rupture failure of OKh16N15M3B steel under conditions of the combined action of reactor irradiation and a dissociating N2O4 heat carrier V. N. KiselevskiiS. S. Tishchenko Scientific-Technical Section Pages: 877 - 881
Influence of the rate of tension on the strength and deformation characteristics of titanium alloys in a wide temperature range V. M. Tokarev Scientific-Technical Section Pages: 882 - 886
Determination of the dynamic characteristics of fracture toughness on ring specimens in loading using a vertical impact tester V. A. Makovei Production Section Pages: 887 - 890
Long-term ductility of a bainitic steel L. D. MishchenkoS. S. D'yachenkoV. P. Tarabanova Production Section Pages: 891 - 894
Predicting the reliability of load-carrying components of machines in sudden failures A. N. Savos'kinV. V. Frants Production Section Pages: 895 - 899
Examination of elastoplastic problems by the holographic moiré method V. A. Zhilkin Production Section Pages: 900 - 904
Automated system for investigating the thermal stability of ceramic and refractory materials G. A. GogotsiA. V. DrozdovN. N. Radin Production Section Pages: 905 - 908
Examination of the fatigue resistance of creep-resisting nickel alloys with coatings V. N. PavlovE. Ya. PalienkoA. D. Pogrebnyak Production Section Pages: 913 - 918
Analysis of damage and diagnostics of the condition of the metal of boiler units during service I. A. KozlovN. V. BugaiV. S. Zamotaev Production Section Pages: 918 - 923