Volume 15, Issue 12 | Strength of Materials

Strength of Materials

Publishing model:: Subscription

Search all Strength of Materials articles

Volume 15, Issue 12

December 1983

Filter by

Volume:

Sort by

Date published:

New to old Old to new

30 articles in this issue

Special features of transformation of the yield surface of a chromium steel
A. A. Lebedev
A. V. Troshchenko
N. M. Kul'chitskii
Scientific-Technical Section Pages: 1645 - 1650
Criteria of fatigue failure of components with coatings
V. S. Kalmutskii
Scientific-Technical Section Pages: 1650 - 1654
Examination of the effect of high-parameter water on the kinetics of multicycle fatigue damage in steel
P. A. Pavlov
B. A. Kadyrbekov
A. I. Ainabekov
Scientific-Technical Section Pages: 1654 - 1658
Examining cyclic creep of structural alloys using the acoustic-emission method
V. A. Strizhalo
M. V. Kalashkin
S. I. Likhatskii
Scientific-Technical Section Pages: 1659 - 1662
Using goodness-of-fit criteria for analyzing the results of fatigue tests
B. F. Balashov
V. P. Khar'kov
Z. Kh. Yurovskii
Scientific-Technical Section Pages: 1663 - 1668
Residual stresses and fatigue strength of screw joints
S. I. Ivanov
N. G. Trofimov
V. K. Krasota
Scientific-Technical Section Pages: 1669 - 1671
Resistance of titanium alloys to impact fatigue failure
K. K. Karandashov
G. V. Toporov
V. P. Pershin
Scientific-Technical Section Pages: 1671 - 1675
Evaluation of the fatigue strength of creep-resisting materials by microhardness measurements. Report 1. Relationships governing changes of the surface condition during fatigue
A. D. Pogrebnyak
A. V. Zheldubovskii
Scientific-Technical Section Pages: 1675 - 1680
Calculating the life of the element of the wing panel
A. V. Kirillov
A. S. Mostovoi
Scientific-Technical Section Pages: 1681 - 1686
Computer modeling of the deformation kinetics in the plastic zone near a crack tip
V. I. Vladimirov
D. N. Karpinskii
S. V. Sannikov
Scientific-Technical Section Pages: 1687 - 1693
Influence of loading conditions on fatigue crack growth rate in stainless steels in air and in sea salt solution
A. V. Prokopenko
V. N. Torgov
L. B. Getsov
Scientific-Technical Section Pages: 1694 - 1699
Influence of anticorrosion surfacing on the fracture toughness of 15Kh2NMFA steel
K. L. Il'inskii
G. S. Vasil'chenko
N. A. Ledovskikh
Scientific-Technical Section Pages: 1699 - 1702
Determination of crack resistance of ATM-1 carbon-graphite material
S. S. Zhunisbekov
V. P. Naumenko
G. S. Pastukhov
Scientific-Technical Section Pages: 1703 - 1708
Influence of cathodic protection on the crack resistance in cyclic loading of 15Kh12N2VMF and 08Kh17N6T steels and VT3-1 alloy in sea salt solution
A. V. Prokopenko
V. N. Torgov
L. B. Getsov
Scientific-Technical Section Pages: 1709 - 1711
Limit state of circular plate with intricately shaped crack
A. V. Boiko
L. N. Karpenko
Scientific-Technical Section Pages: 1712 - 1717
Stress waves in a plate induced by a surface load moving at constant speed
G. V. Stepanov
Scientific-Technical Section Pages: 1718 - 1722
Evaluation of the accuracy of solutions of problems of the theory of elasticity obtained in the schema of the method of boundary integral equations. Communication 1
D. K. Yakimchuk
I. Mashinda
Scientific-Technical Section Pages: 1723 - 1725
Optimizing the design of laminated composites
N. V. Kotov
V. N. Mukhin
Scientific-Technical Section Pages: 1726 - 1730
Theoretical and experimental investigation of the design and technological contact problem of stamping. Communication 1
Yu. B. Gnuchii
Scientific-Technical Section Pages: 1730 - 1736
Evaluation of the limiting state of defective drawing dies. Report 3. Analytical solution of the problem of the limiting state of a defective drawing die with a reinforcing ring
M. P. Savruk
I. V. Prokopchuk
N. M. Kamenev
Scientific-Technical Section Pages: 1736 - 1741
Effectiveness of banding pipes and cylindrical shells
A. I. Smirnov
Scientific-Technical Section Pages: 1742 - 1745
Geometrically and physically nonlinear bending of steeply sloping shells with various shapes under simultaneous effect of temperature and external forces
M. M. Kornishin
M. M. Suleimanova
Scientific-Technical Section Pages: 1746 - 1750
Damping capacity of rods of materials with different mechanism of energy dissipation in two-frequency flexural vibrations
A. P. Bovsunovskii
V. V. Matveev
B. S. Chaikovskii
Scientific-Technical Section Pages: 1751 - 1755
Effect of high-temperature oxidation in liquid fule combustion products on the strength characteristics of sintered sealing material Nichrome Kh20N80-boron nitride
E. I. Kuznetsov
V. A. Satanin
Scientific-Technical Section Pages: 1756 - 1758
Heat-resistant characteristics of molybdenum-base alloys
I. S. Tsvilyuk
V. I. Pyl'nikov
D. S. Avramenko
Scientific-Technical Section Pages: 1759 - 1762
Features of the fracture surface for molybdenum alloys with different grain size and in the presence of secondary phase particles
É. P. Pechkovskii
Scientific-Technical Section Pages: 1762 - 1767
Study of temperature dependences for the mechanical properties of low-alloy steels with static and dynamic loading
G. I. Saidov
A. A. Ostsemin
Scientific-Technical Section Pages: 1768 - 1770
Stiffness of composite rods based on boron-reinforced plastic at room and cryogenic temperatures
A. F. Voitenko
M. P. Zemtsov
V. S. Pirogov
Scientific-Technical Section Pages: 1771 - 1773
Dependence of the elastic modulus on the physical properties of a material
Yu. Ya. Leus
Kh. M. Khanukhov
Scientific-Technical Section Pages: 1773 - 1777
Design of a demountable joint for an external-pressure shell made of brittle material
K. P. Gorbachev
V. V. Dreko
N. A. Popova
Production Section Pages: 1778 - 1781