Deformation and life of materials with different cycle asymmetries of the change in stress intensity on curved trajectories N. S. MozharovskiiA. A. Zakhovaiko Scientific-Technical Section Pages: 1349 - 1356
Determination of the life of constructional steels under conditions of cyclic creep in the plane stressed state F. F. GiginyakM. V. Storchak Scientific-Technical Section Pages: 1356 - 1358
Prediction of stress-rupture strength on the basis of the pheno-menological theory of damage of a material in creep V. É. Fraifel'dO. V. Sorokin Scientific-Technical Section Pages: 1359 - 1365
Influence of cycle asymmetry on the fatigue resistance of heat-resistant steel with long loading bases I. A. TroyanA. D. Shevchuk Scientific-Technical Section Pages: 1366 - 1370
Statistical prediction of the stress-rupture strength of an austenitic steel V. A. Man'kovskii Scientific-Technical Section Pages: 1370 - 1375
Accelerated tests of determining the endurance limit as an efficient method of evaluating the accepted design and technological solutions B. V. BoitsovE. P. Obolenskii Scientific-Technical Section Pages: 1375 - 1383
Principles of the cyclic creep of steel 15Kh2NMFA in a complex stress state F. F. GiginyakM. V. StorchakT. N. Mozharovskaya Scientific-Technical Section Pages: 1383 - 1390
Evaluating the limiting state of defective drawplates. Report no. 2. Use of model representations to describe the limiting state of a drawplate with a crack N. V. NovikovN. M. KamenevV. N. Kulakovskii Scientific-Technical Section Pages: 1391 - 1394
Evaluating the limiting state of shearable elements A. P. Zhukovets Scientific-Technical Section Pages: 1395 - 1402
Experimental study of residual stresses in reels of magnetic tape É. S. UmanskiiN. S. Shidlovskii Scientific-Technical Section Pages: 1402 - 1409
Study of the stress-strain state of hollow curvilinearly orthotropic cylinders V. L. RvachevN. S. SinekopN. I. Sinekop Scientific-Technical Section Pages: 1410 - 1415
Strength evaluation for a composite rod structure made of brittle material with a glued joint I. I. D'yachkovV. S. Morganyuk Scientific-Technical Section Pages: 1416 - 1422
Load-carrying capacity of the glass-epoxy blade of an axial fan G. P. ZaitsevS. A. Silant'evV. P. Mel'nikov Scientific-Technical Section Pages: 1422 - 1426
Network model of an elastic body with sources of boundary loads. Report 3 E. G. Kuzovkov Scientific-Technical Section Pages: 1427 - 1435
Certain problems of optimum pin design for rotors of the drum-disc type under antisymmetric loading N. P. ZnamenskiiN. I. Koterov Scientific-Technical Section Pages: 1435 - 1439
Plane problem of the theory of elasticity for an arbitrary system of cracks in a circle with displacements specified on its boundary L. N. KarpenkoA. V. Boiko Scientific-Technical Section Pages: 1439 - 1443
Theoretical method of estimating the parameters of the kinetic equation of crack growth M. V. Baumshtein Scientific-Technical Section Pages: 1443 - 1447
Change of the damping ability upon aging of the β alloy of the system Cu−Al−Zn with reversible martensite in the structure O. G. ZotovS. Yu. Kondrat'evV. V. Matveev Scientific-Technical Section Pages: 1447 - 1451
Vibrations of gas-turbine engine blower impellers with changing conditions at the engine inlet D. S. ElenevskiiV. V. Malygin Scientific-Technical Section Pages: 1452 - 1457
Oscillations of a circular two-layer metal-polymer plate V. S. DidkovskiiÉ. I. StarovoitovT. A. Starovoitova Scientific-Technical Section Pages: 1457 - 1462
Study of wave stresses in plates made of anisotropic materials by the method of dynamic photoelasticity Z. G. AlpaidzeI. Kh. KostinV. I. Pakhunov Scientific-Technical Section Pages: 1462 - 1468
Energy characteristics of failure for an aluminum plate with punching by a steel striker V. V. AstaininG. V. Stepanov Scientific-Technical Section Pages: 1468 - 1471
Deformation mechanisms for steel with high-temperature tests V. P. KrashchenkoV. N. Yakovkin Scientific-Technical Section Pages: 1472 - 1475
Effect of alloying with nitrogen on the long-term strength characteristics of welded joints in molybdenum-based alloys I. S. TsvilyukE. P. PolishchukD. S. Avramenko Scientific-Technical Section Pages: 1476 - 1481
Necking in tensile tests of cylindrical specimens S. S. Oding Scientific-Technical Section Pages: 1482 - 1485
Effect of contact friction forces in compressive tests of specimens V. I. Koval'Yu. B. GnuchiiV. S. Morganyuk Scientific-Technical Section Pages: 1486 - 1487
More accurate determination of the region of application of the method of upsetting specimens with flat ends V. A. KrokhaV. E. Planida Scientific-Technical Section Pages: 1488 - 1494
A method of determining the strength of thick-walled welded joints with a soft profile weld Yu. V. AbitkovskiiV. A. IgnatovB. T. Timofeev Scientific-Technical Section Pages: 1495 - 1498
Thermal stresses in a multilayer semiconductor structure V. I. LavrenyukV. A. Makara Scientific-Technical Section Pages: 1499 - 1504
Effect of plastic surface strain methods on resistance to relaxation of AL4 aluminum alloy N. Ya. Yakh"yaev Production Section Pages: 1505 - 1508