High-Alumina ramming bodies for lining steel casting ladles having provision for vacuum refining Yu. A. PirogovV. N. Savel'evG. A. Ivshina OriginalPaper Pages: 259 - 263
Determination of the material composition of the finely milled binder in magnesic-spinellid refractories R. A. PanfilovV. M. Ust'yantsevS. P. Postnikova OriginalPaper Pages: 264 - 267
Optimizing the composition of thermal-shock resistant ceramics based on magnesium chromite V. Kh. Kuliev OriginalPaper Pages: 267 - 271
Highly concentrated ceramic bonding suspensions. Mechanism and features of structure formation during drying Yu. E. PivinskiiS. G. SemikovaM. A. Trubitsyn OriginalPaper Pages: 272 - 278
Generalized diagrams and creep limits of dinas refractories for coke furnaces I. I. VishnevskiiL. D. SmirnovaYu. N. Yarovoi OriginalPaper Pages: 279 - 284
Structural homogenization in a fibrous insulator containing an inorganic binder E. V. VazheninV. A. GorodetskiiM. Z. Naginskii OriginalPaper Pages: 285 - 287
Performance estimation for flame guniting programs Yu. N. MirovL. P. Gashtol'dA. P. Bogdanov OriginalPaper Pages: 288 - 292
Effects of pressing pressure on forsterite refractory density G. I. AntonovYu. L. KamenetskiiA. G. Antonov OriginalPaper Pages: 292 - 295
Titanium transfer from molten steel to the lining in a vacuum induction oven B. G. Chernov OriginalPaper Pages: 296 - 298
Improving the briquetting method for high-alumina cement Ya. Z. ShapiroL. G. LitvinT. P. Kupalova OriginalPaper Pages: 299 - 301
Introduction of the production of sand-cellulose curved thermal insulation inserts V. A. OsipovV. P. VozhdaevV. P. Nogtev OriginalPaper Pages: 301 - 302
Operation of type OKB-2126 furnaces for production of molten and cast refractory materials B. P. AleksandrovV. I. GutmanT. A. Vyrodova OriginalPaper Pages: 303 - 306
Thermal expansion of dinas — The basis of drying and heating the lining of coke batteries V. L. BulakhV. I. PechenezhskiiG. M. Vol'fovskii OriginalPaper Pages: 307 - 311
Spectral emissivity of refractories (review article) M. S. GlazmanYa. A. LandaN. A. Puchkelevich ReviewPaper Pages: 312 - 319
Creep of a dinas based mortar used in coke ovens I. I. VishnevskiiL. D. SmirnovaYu. N. Yarovoi OriginalPaper Pages: 323 - 328
Highly concentrated ceramic binder suspensions. Wet milling processes and technological problems Yu. E. Pivinskii OriginalPaper Pages: 328 - 335
Granulation of particulate oxide materials N. M. ChudnovaI. F. UsatikovT. M. Shlyakhova OriginalPaper Pages: 335 - 338
Al2O3-ZrO2 Ceramics made from powders obtained by rapid hardening from the melt V. A. KryuchkovL. P. IvanovaA. A. Ezhov OriginalPaper Pages: 346 - 349
Investigation of mullite obtained by fusion in Solar furnaces G. T. AdylovB. E. BibershteinÉ. M. Urazaeva OriginalPaper Pages: 349 - 353
Wettability of aluminosilicate coatings by Sn, Pb, Ge melts N. N. LebedevaV. V. Bakovets OriginalPaper Pages: 353 - 354
Investigation of the transfer of metallic constituents of refractory oxides of a lining into liquid steel during storage in vacuum B. G. Chernov OriginalPaper Pages: 354 - 356
Determination of the mass proportion of aluminum oxide in aluminosilicate raw material using the BARS-3 instrument V. S. RybakovV. A. EsipovaE. E. Glinskii OriginalPaper Pages: 361 - 362
Rational use of caustic magnesite dust in the production of refractories K. V. SimonovV. V. ZagnoikoV. M. Ust'yntsev OriginalPaper Pages: 363 - 371
An important direction in increasing the effectiveness of coke and refractory production A. I. SibilevN. S. KotenkoA. K. Purgin OriginalPaper Pages: 371 - 373
A method of calculation of the standards of fuel consumption in tunnel kilns on a microcomputer E. P. Grigor'evYu. N. MirovV. G. Abbakumov OriginalPaper Pages: 374 - 377
Coefficient of thermal diffusivity of refractory and ceramic materials V. V. KolomeitsevK. N. Dergunov OriginalPaper Pages: 378 - 380
A concrete for lining blast furnace shafts N. V. PitakR. M. FedorukV. A. Chechenev OriginalPaper Pages: 381 - 384
Refractories for the slide gates of the steel-teeming ladles of the electric melt shop of belorussian metallurgical plant A. A. Kortel'A. L. DurmashkinN. N. Fomenko OriginalPaper Pages: 385 - 389
Reasons for unsatisfactory refractory service in the zone of the metal of a batch vacuum degasser V. G. KukarekoA. I. UstinovV. A. Orlov OriginalPaper Pages: 389 - 391
Fastening of fiber thermal insulation with refractory cement V. G. OvsyannikovV. I. TarasovYu. P. Kurilov OriginalPaper Pages: 392 - 393
