Photosedimentation analysis of powders I. A. KiyanskiiB. A. BorokZh. I. Dzneladze Theory, Production, and Properties of Powders and Fibers Pages: 874 - 877
Microstructural changes produced by annealing in particles of industrial APS-1, APS-2, AND APS-3 aluminum powders A. I. LitvintsevK. V. IvashkoL. N. Klimova Theory, Production, and Properties of Powders and Fibers Pages: 878 - 882
Stress reduction during the densification of metal powders B. D. YurchenkoO. P. Ovchinnikov Theory and Technology of Component-Formation Process Pages: 883 - 886
Effect of dispersed Al2O3 inclusions on the densification of 80% Ni-20% Cr alloys during sintering V. N. AntsiferovV. A. Polyakov Theory and Technology of Sintering, Thermal, and Chemicothermal Treatment Processes Pages: 887 - 891
Sintered high-manganese steel Yu. G. DorofeevN. T. ZherditskiiV. A. Kolesnikov Sintered Materials and Components Pages: 892 - 894
Preparation of barium hexaferrite from mixtures of ferric oxide and barium nitrate or barium oxides and from mixtures produced by nonceramic methods I. V. GranovskiiYu. D. StepanovaE. M. Krisan' Sintered Materials and Components Pages: 895 - 901
Equations for calculating mass flow rates of liquids and gases in porous media Ya. F. Masalov Test Methods and Properties of Materials Pages: 902 - 907
An x-ray spectral study of the electronic structure of zirconium nitride L. B. LitvinovaN. S. Pastushuk Test Methods and Properties of Materials Pages: 908 - 911
Structural and phase changes induced in Fe-S composites by heating L. F. KolesnichenkoP. V. Trushko Test Methods and Properties of Materials Pages: 912 - 916
Electrical conductivity of materials from mixed aluminum and silicon nitrides A. G. GorbatovV. M. Kamyshov Test Methods and Properties of Materials Pages: 917 - 920
Solubility of carbon in molybdenum-tungsten solid solutions L. V. GorshkovaF. I. Shamrai Test Methods and Properties of Materials Pages: 921 - 924
Bond strength of coatings applied by the flame plating technique B. M. ZakharovM. G. TrofimovV. V. Vinokurova Test Methods and Properties of Materials Pages: 925 - 929
Wear resistance of refractory compounds in the continuous micromachining of titanium and nickel A. I. BezykornovN. I. BogomolovM. S. Koval'chenko Test Methods and Properties of Materials Pages: 930 - 934
Choice of materials for operation in an abrasive-laden air stream G. V. SamsonovA. A. Dan'kin Test Methods and Properties of Materials Pages: 935 - 939
Determination of the initial solid-phase reduction temperatures of substances T. M. Evtushok Test Methods and Properties of Materials Pages: 940 - 941
Effect of the particle size of starting powders on the results of spectral analysis of sintered materials O. I. FushchichA. S. Dem'yanchuk Test Methods and Properties of Materials Pages: 942 - 945
Manufacture of thin-walled tubular filters from porous titanium sheets G. F. TikhonovV. K. Sorokin Powder Metallurgy Industry, Economics, and Organization of Production Pages: 946 - 947
Industrial experience with the application of electrolytic coatings to parts from iron powder L. M. ApininskayaG. D. Sozonov Exchange of Experience and Information Pages: 948 - 949
An improved muffle for the sintering of powder metallurgical parts O. D. Bussel'P. A. Kulu Exchange of Experience and Information Pages: 950 - 951