Elemental, liquid ammonia facilitated routes to zinc, cadmium, mercury copper, silver and lead telluride G. HenshawI. P. ParkinG. Shaw OriginalPaper Pages: 1741 - 1742
Microstructural studies of SiC continuous fibre/nitrided-bonded SiC composites K. ParkS. G. DipietroG. S. Thurston OriginalPaper Pages: 1743 - 1746
Raman studies on PbTiO3 thin films by modified sol-gel processing Tao ZhuGaorong HanZhengfu Han OriginalPaper Pages: 1747 - 1748
Heating rate dependence of precipitation in an Al-1%Si alloy M. J. Starink OriginalPaper Pages: 1749 - 1751
An empirical correlation between the electrical conductivity and the thermal conductivity for elements: a refinement of the Wiedemann-Franz law S. Tamura OriginalPaper Pages: 1752 - 1753
Surface modification of aluminium nitride powder Y. Q. LiT. QiuX. C. He OriginalPaper Pages: 1758 - 1761
Low energy synthesis of an [NZP] material using oxidation of metals E. Breval OriginalPaper Pages: 1762 - 1764
Dielectric strength of fine grained barium titanate ceramics T. TunkasiriG. Rujijanagul OriginalPaper Pages: 1767 - 1769
Mechanical properties of porous carbon materials i.e. woodceramics H. IizukaM. FushitaniK. Hokkirigawa OriginalPaper Pages: 1770 - 1772
Influence of the size and morphology of silicon particles on the physical, mechanical and tribological properties of some aluminium — silicon alloys B. K. PrasadK. VenkateswarluA. H. Yegneswaran OriginalPaper Pages: 1773 - 1776
Preparation and gas permeation properties of ceramic-silicalite membranes J. PetersenK. -V. Peinemann OriginalPaper Pages: 1777 - 1780
Mossbauer studies on strain-induced martensite transformation in Fe-6Mn-1C alloy Zhang FuchengJing TianfuZheng Yangzang OriginalPaper Pages: 1784 - 1785
A microstructural study of the improved ablation resistance of carbon/phenolic composites fabricated using H3PO4-coated carbon fibres Donghwan Cho OriginalPaper Pages: 1786 - 1788
Grain size dependence of anatase-to-rutile structural transformation in gel-derived nanocrystalline titania powders X. -Z. DingX. -H. LiuY. -Z. He OriginalPaper Pages: 1789 - 1791
The electro-discharge machining surfaces of high-chromium white irons C. P. Tabrett OriginalPaper Pages: 1792 - 1794
Phase relations in the Pr-Cu-0 system at 1000 °C T. ShimazakiK. TerayamaM. Yoshimura OriginalPaper Pages: 1795 - 1798
Formation of zirconium nitride via mechanochemical processing T. PuclinW. A. Kaczmarek OriginalPaper Pages: 1799 - 1800
Microstructure changes in plasma sprayed TiAl coatings after hot isostatic pressing K. A. KhorY. MurakoshiT. Sang OriginalPaper Pages: 1801 - 1804
The nature of the defective structure α-silicon nitride Chong-Min WangTian-Min Wang OriginalPaper Pages: 1805 - 1807
Preparation and structure of Ba(Mg1/3Ta2/3)O3 thin films derived from a sol-gel process Ji ZhouQing-Xin SuD. J. Barber OriginalPaper Pages: 1808 - 1810
Thermal decomposition kinetics of ferric and ammonium sulphates obtained by bio-oxidation of water pickling liquors with Thiobacillus ferrooxidans F. A. LopezA. Lopez-Delgado OriginalPaper Pages: 1811 - 1814
Effects of CaO addition on sintering and mechanical properties of Al2O3 T. NagaokaM. YasuokaY. Yamaoka OriginalPaper Pages: 1815 - 1817
Hardness of titanium nitride coatings fabricated by vacuum arc deposition N. A. TravitzkyV. N. Zhitomirsky OriginalPaper Pages: 1818 - 1820
A special technique for determining the bond strength of micro-fibres in cement matrix by pullout test A. KatzV. C. Li OriginalPaper Pages: 1821 - 1823
The structure and strain relief in epitaxially grown CdSe on ZnSe by atomic layer epitaxy Y. Z. FengS. P. Guo OriginalPaper Pages: 1824 - 1827
Application of recycled tyre cord in concrete for shrinkage crack control Hwai-Chung WuYun Mook LimV. C. Li OriginalPaper Pages: 1828 - 1831