Effective hardware for connection and repair of polyethylene pipelines using ultrasound modification and heat shrinking. Part 5. Aspects of thermistor couplings and components used in gas-pipeline repair A. E. KolosovO. S. SakharovS. O. Pristailov OriginalPaper 21 July 2011 Article: 285
Effective hardware for connection and repair of polyethylene pipelines using ultrasonic modification and heat shrinkage. Part 4. Characteristics of practical implementation of production bases developed using epoxy-glue compositions and banding* A. E. KolosovO. S. SakharovS. O. Pristailov Safety, Diagnosis, and Repair 21 July 2011 Article: 280
Approval of a pyrolysis procedure in an experimental unit V. G. SisterE. M. IvannikovaYu. V. Lugovoi Industrial Ecology 21 July 2011 Article: 274
Use of a neural network approach to optimizing concrete composition with respect to strength A. R. MukhutdinovS. I. KonstantinovG. M. Mukhutdinova OriginalPaper 21 July 2011 Article: 270
Development of a neural network programming module for predicting the strength properties of solid fuel A. R. MukhutdinovM. V. Okulin Computerizing Calculations and Designing 21 July 2011 Article: 266
Vacuum-crystallization units for the production of magnesium from serpentinite D. S. TretyakovV. A. RyabkovA. I. Potekha OriginalPaper 21 July 2011 Article: 261
Criterion of analysis of the action of inertial force in medium- and high-speed milling units P. E. Vaitekhovich OriginalPaper 23 July 2011 Article: 256
Development and test of a new drop trap E. N. PetrashovaM. G. LagutkinV. I. Shishov OriginalPaper 23 July 2011 Article: 250
Determination of rolling time for thermoplastic compositions I. O. Mikulenok OriginalPaper 23 July 2011 Article: 243
Method of analyzing heat exchange in a layer of disperse material purged by a gas flow R. Sh. SufiyanovA. V. KhvanI. S. Maikov OriginalPaper 21 July 2011 Article: 238
Extrusion molding of polymers with allowance for near-wall slip A. S. SakharovV. I. SivetskiiA. L. Sokolskii OriginalPaper 23 July 2011 Article: 231
Limiting plastic load for a pressure vessel with a tangential branch pipe V. N. SkopinskiiN. A. BerkovN. V. Vozhova Research, Design, Calculations, and Operating Experience 21 July 2011 Article: 225
Effective hardware for connection and repair of polyethylene pipelines using ultrasonic modification and heat shrinkage. Part 3. Analysis of surface-treatment methods for polyethylene pipes connected by banding A. E. KolosovO. S. SakharovS. O. Pristailov OriginalPaper 21 July 2011 Article: 216
Effective hardware for connection and repair of polyethylene pipelines using ultrasonic modification and heat shrinkage. Part 2. Production bases for molding of epoxy repair couplings with shape memory A. E. KolosovO. S. SakharovS. O. Pristailov OriginalPaper 23 July 2011 Article: 210
Effective hardware for connection and repair of polyethylene pipelines using ultrasonic modification and heat shrinkage. Part 1. Aspects of connection and restoration of polymeric pipelines for gas transport A. E. KolosovO. S. SakharovS. O. Pristailov Safety, Diagnosis, and Repair 23 July 2011 Article: 204
Ecological problems of utilization of waste activated sludge of saratov refinery and ways to solve them N. A. SobgaidaL. N. OlshanskayaA. B. Solodkova Industrial Ecology 23 July 2011 Article: 198
Detachable sealed joint having two successively placed sealing elements V. D. Prodan OriginalPaper 26 July 2011 Article: 193
Influence of type of high-coercivity permanent magnet on characteristics of end magnetic clutch A. Ya. KrasilnikovA. A. Krasilnikov OriginalPaper 26 July 2011 Article: 186
Cryogenic engineering, production and use of industrial gases, vacuum engineering B. T. MarinyukS. I. BazhinovM. F. Rudenko OriginalPaper 23 July 2011 Article: 184
Modeling the vertical flow of a gaseous mixture with solid inclusions in a cylindrical pipe M. G. BerengartenR. I. BogdanovV. A. Titov OriginalPaper 21 July 2011 Article: 173
Optimization of components of molding rotors for automated production lines S. V. TeplishchevV. Yu. Arkhangelskii OriginalPaper 21 July 2011 Article: 167
Analysis of the power of a rotary-press drive for the molding of multiple-component combined articles V. Yu. ArkhangelskiiS. V. Teplishchev Research, Design, Calculations, and Operating Experience 21 July 2011 Article: 161