1. A new ANT-100S pump unit for cold-climate oil fields

   • É. S. Ibragimov
   • R. E. Gazarov

   OriginalPaper Pages: 681 - 682

2. Shell and tube heat-exchange condensers with a glassy enamel coating

   • V. T. Fotokakis
   • S. L. Yampol'skii
   • N. F. Shvab

   OriginalPaper Pages: 683 - 685

3. New equipment for manual plasma arc metal cutting

   • K. V. Vasil'ev
   • A. M. Komissarov
   • A. A. Isachenko

   OriginalPaper Pages: 686 - 689

4. Investigation of strength of VT1-0 titanium alloy vessels

   • M. V. Danilov
   • S. M. Kutepov
   • K. V. Smol'skii

   Design and Construction of Machinery and Equipment Pages: 690 - 693

5. Analytical method for determination of dynamic loading in an electric drive armature

   • O. N. Shpakov

   Design and Construction of Machinery and Equipment Pages: 694 - 695

6. Design method for safety valves with pressure applied above the seat

   • I. S. Grinberg
   • I. R. Krichker

   Design and Construction of Machinery and Equipment Pages: 696 - 698

7. Calculating the length of the orientation zone and drive power of units for orienting polyethylene terephthalate film

   • V. I. Ivanov
   • G. V. Sagalaev

   Design and Construction of Machinery and Equipment Pages: 699 - 703

8. Laws of filtration during removal of contaminants from Nitric acid

   • K. V. Rybakov
   • V. P. Kovalenko
   • L. M. Rozanova

   Investigation and Calculation of Thermochemical Processes Pages: 704 - 705

9. The dust-extracting efficiency of equipment using a fluidized bed of spherical particles

   • A. Yu. Val'dberg
   • N. I. Gel'perin
   • É. Ya. Tarat

   Investigation and Calculation of Thermochemical Processes Pages: 706 - 710

10. Thin-layer rotor evaporator with a stepped heat-transfer surface

    • A. N. Marchenko
    • O. N. Solyanik
    • V. D. Nerubatskaya

    Investigation and Calculation of Thermochemical Processes Pages: 711 - 713

11. Calculation of steady-state thermal conditions of a multi-block evaporator with a steam-jet compressor

    • L. L. Murav'ev
    • V. S. Postikov

    Investigation and Calculation of Thermochemical Processes Pages: 714 - 716

12. Steel 1Kh2M1 tubing for furnace coils of catalytic reformers

    • V. G. D'yakov
    • Yu. S. Medvedev
    • E. V. Bush

    New Materials and Corrosion Control Pages: 717 - 719

13. Anticorrosion coatings from liquid neoprene

    • V. T. Kopylov
    • V. I. Kononova
    • V. V. Furnichenko

    New Materials and Corrosion Control Pages: 720 - 721

14. Fabrication of new extruder screws and restoration of worn extruder screws by plasma hardfacing

    • A. M. Maksimchuk
    • G. A. Mesyats
    • L. P. Andreev

    Equipment Fabrication Technology Pages: 722 - 724

15. Precision in the manufacture of filled-Kapron piston rings

    • N. P. Bykov
    • V. A. Kuz'min
    • A. S. Motora

    Equipment Fabrication Technology Pages: 725 - 726

16. Determination of the actual clearance of the plunger pairs of serially manufactured oilwell pumps

    • Yu. A. Saakov
    • A. M. Rabinovich

    Equipment Fabrication Technology Pages: 727 - 730

17. Experimental investigation of flanging with thinning of shell

    • N. I. Zhil'tsov
    • E. P. Subbotin

    Equipment Fabrication Technology Pages: 731 - 734

18. Dimensional series of electrical pumps for pumping out contaminated water

    • I. N. Fel'gendler
    • B. V. Khimach

    Normalization and Standardization Pages: 735 - 737

19. Standardization of reciprocating compressor crossheads

    • M. E. Kashevarov
    • V. G. Khibrikov

    Normalization and Standardization Pages: 738 - 738

20. Experience in organization of standard cost system in computerized data media under conditions of single-unit, multiple-item production

    • A. N. Kuvalkin
    • E. E. Karpov
    • V. V. Burov

    Organization and Economics of Production Pages: 739 - 741

21. Problem of optimizing capital investments in chemical and petroleum machinery construction industry branch

    • L. V. Alievskaya
    • G. S. Popova
    • A. D. Shapiro

    Organization and Economics of Production Pages: 742 - 746

22. A method for quantitative evaluation of the reliability of mechanical elements of cryogenic systems from results of weighted tests

    • M. V. Zhirov

    Quality, Reliability, and Lifetime Pages: 747 - 748

23. Effect of variable pressure on wear and breakdown of nonmetallic piston rings

    • V. S. Davydov
    • B. S. Fotin
    • L A. Shteingart

    Quality, Reliability, and Lifetime Pages: 749 - 754

24. Competition for monthly overfulfillment of the plan for growth of labor productivity at every workplace

    • A. A. Kolesnikov
    • A. I. Tret'yakova

    Exchange of Experience Pages: 755 - 756

25. Equipment for the mechanized cutting of circular and elliptical holes in the walls of cylindrical vessels

    • G. M. Fokin

    Exchange of Experience Pages: 757 - 759

26. Forming vessel heads at the Dzerzhinsk Chemical Equipment Construction Plant (DCECP)

    • K. A. Popov
    • S. Yu. Bobovich
    • B. N. Shevelkin

    Exchange of Experience Pages: 760 - 761

27. A device for measurement of the axial perpendicularity of two holes

    • S. V. Ryumin

    Exchange of Experience Pages: 762 - 763

28. Rim vulcanizer

    Information Pages: 764 - 765

29. Plant with twin-screw granulator for cable plasticized resins based on PVC

    Production of New Equipment Pages: 766 - 767

30. Thickener U-210

    Production of New Equipment Pages: 768 - 768

31. Specialists in technical esthetics improve their skills

    • S. S. Kleimeshova

    Production of New Equipment Pages: 769 - 769

32. Results from experimental testing of end seals for high pressure apparatus

    • E. V. Shataev
    • R. M. Starodubov
    • M. D. Volkova

    Production of New Equipment Pages: 770 - 773

33. Pressure regulator

    • V. S. Mokrousov

    Production of New Equipment Pages: 774 - 774

34. Protection of a carbon monoxide generator from pit corrosion

    • I. V. Riskin
    • V. V. Krasnoyarskii

    Production of New Equipment Pages: 775 - 776