1. New pumps produced by the Uralgidromash scientific-production organization

   • B. A. Vakhrameev

   New Machinery and Equipment Pages: 787 - 788

2. Type SrSh reversible conveyer mixer

   • A. E. Kurinnyi
   • B. G. Kananin
   • I. I. Bagrintsev

   New Machinery and Equipment Pages: 789 - 790

3. Single-stage high pressure (HP) turboexpander

   • A. B. Davydov
   • E. P. Krylov
   • V. S. Kartashov

   Design and Construction of Machinery and Equipment Pages: 791 - 794

4. Calculation of loads on shaft end seals

   • A. D. Domashnev
   • Y. A. Mel'nik

   Design and Construction of Machinery and Equipment Pages: 795 - 797

5. The design of lens-ring expansion joints with low corrugation height

   • B. M. Ankirskii

   Design and Construction of Machinery and Equipment Pages: 798 - 802

6. Study of operating conditions of the valve seat and body of a drilling piston pump

   • V. I. Poshchupkin
   • S. V. Lovchev
   • B. I. Braslavskii

   Design and Construction of Machinery and Equipment Pages: 803 - 806

7. Performance analysis of a screw-lever mechanism

   • V. M. Zemtsov

   Design and Construction of Machinery and Equipment Pages: 807 - 810

8. Improved design of drum and disk filters

   • V. L. Radushkevich

   Investigation and Calculation of Thermophysical Processes Pages: 811 - 815

9. Evaluation of short cycle, adiabatic air driers

   • V. I. Ermakov
   • Yu. A. Seregin
   • N. S. Torocheshnikov

   Investigation and Calculation of Thermophysical Processes Pages: 816 - 818

10. Performance of a pulsed extractor column with transverse compartmented plates

    • G. I. Ivanov
    • V. N. Doronin

    Investigation and Calculation of Thermophysical Processes Pages: 819 - 820

11. Investigation of the corrosion resistance of materials used in the production of methylmethacrylate

    • G. V. Klimova
    • M. M. Kristal'
    • D. I. Shetulov

    New Materials and Corrosion Control Pages: 821 - 822

12. Corrosion resistance of structural materials under acidic and alkaline conditions

    • Yu. I. Perin
    • R. A. Valieva
    • M. R. Klochkova

    New Materials and Corrosion Control Pages: 823 - 824

13. Corrosion in vulcanizing kettles

    • G. Ya. Vorob'eva
    • L. M. Apraksina

    New Materials and Corrosion Control Pages: 825 - 827

14. Fabrication technology of welded chemical process equipment using rolled bimetal sandwich carbon steel + nickel NP2

    • N. I. Kamakin
    • A. A. Sychev
    • V. A. Rumyantsev

    Equipment Manufacturing Technology Pages: 828 - 832

15. Two-stage grinding of bearing faces for drill bit cones

    • A. A. Akchurin
    • A. N. Filin

    Equipment Manufacturing Technology Pages: 833 - 834

16. Machining products made from chilled cast iron

    • B. F. Fedorov
    • Yu. I. Mal'tsev

    Equipment Manufacturing Technology Pages: 835 - 837

17. Causes for failure of absorption column bases in weak nitric acid plants and methods for their repair

    • A. N. Kuzyukov
    • V. A. Borisenko
    • N. P. Pilyugina

    Equipment Manufacturing Technology Pages: 838 - 839

18. Technical manual RTM 26 64–71 on “impulse-arc welding of stainless steel chemical and petroleum equipment using consumable electrodes and argon shielding”

    • B. P. Kalinin
    • M. A. Chaev

    Normalization and Standardization Pages: 840 - 840

19. Determining the utilization level of air separation units

    • R. D. Malinova
    • N. A. Khomutov

    Organization and Economics of Production Pages: 841 - 844

20. Determination of work capacity of friction pair materials

    • G. E. Lazarev
    • L. I. Nikiforova

    Quality, Reliability, and Lifetime Pages: 845 - 848

21. Resistance to wear of hard alloys at low temperatures

    • P. D. Shnyrev
    • I. N. Drobinin

    Quality, Reliability, and Lifetime Pages: 849 - 850

22. Contact temperature gauge

    • Yu. F. Red'ko
    • S. G. Voronov
    • B. I. Krysyuk

    Exchange of Experience Pages: 851 - 852

23. A new system for feeding a urea melt into granulators

    • Yu. A. Terekhin

    Exchange of Experience Pages: 853 - 853

24. A pneumatic machine for seating reflux valves to the beds of rectification trays

    • Yu. I. Neretin
    • V. M. Davydushkin

    Exchange of Experience Pages: 854 - 855

25. Electromelting tin-bronze in carborundum crucibles

    • A. I. Medvedev

    Exchange of Experience Pages: 856 - 856

26. Plant for processing metallic cord for production of tire covers

    • A. I. Khomyakov
    • B. A. Kantsev

    Information Pages: 857 - 860

27. A device for feeding a pneumatically transported load into a vessel containing a fluidized bed

    • E. Ya. Barsukov
    • D. M. Soskind

    Information Pages: 861 - 862

28. The scientific and technical committee of the ministry for chemical and petroleum engineering

    • V. I. Rublev

    Information Pages: 863 - 865

29. Modern pipeline valve design

    • L. S. Bodnarchuk
    • Ya. L. Shteingrad

    From Foreign Technology Pages: 866 - 870