1. Dry-compression rotor compressors of low capacity

   • V. B. Shnepp
   • A. I. Shvarts
   • I. G. Khisameev

   New Machines and Equipment Pages: 329 - 331

2. Erratum

   Erratum Pages: 332 - 332

3. Standardized mixers ZL and ZSh

   • N. A. Dolgoborodov
   • A. I. Shchechka
   • N. A. Kupriyanov

   New Machines and Equipment Pages: 333 - 334

4. Magnetic rotating units

   • I. V. Sigov
   • Yu. D. Kondrashov
   • A. A. Krut'ko

   New Machines and Equipment Pages: 335 - 336

5. Calculation of the strength of reactors with annular heat-transfer tubes

   • S. S. Oleshev
   • V. D. Medvedev

   Design and Construction of New Machines and Equipment Pages: 337 - 340

6. Calculation of the design parameters of a liquid-phase reactor with mixing device

   • A. K. Nikitin

   Design and Construction of New Machines and Equipment Pages: 341 - 346

7. Development of turboexpanders with low flow rates

   • V. I. Ardashev
   • M. S. Babichev

   Design and Construction of New Machines and Equipment Pages: 346 - 349

8. Effect of experimental error on the precision of determining filtration constants

   • P. G. Vlasov
   • T. M. Grankina
   • V. A. Chernikov

   Process Studies Pages: 350 - 353

9. Analysis of the action of modernized impact-action spray-traps

   • M. Ya. Moroshkin
   • V. N. Smolin

   Process Studies Pages: 354 - 357

10. Calculation of leaks in an oil-filled rotary compressor

    • A. N. Sherstyuk
    • I. S. Bodik

    Process Studies Pages: 357 - 360

11. Nonisothermal flow of non-Newtonian liquids in worm extruders with conical cores

    • V. P. Pervadchuk
    • V. I. Yankov
    • I. Z. Kunin

    Process Studies Pages: 360 - 364

12. New methods for absorption of vibration and reduction of crack growth

    • E. I. Lishchishin
    • V. M. Tsmots'

    Quality, Reliability, and Durability Pages: 365 - 366

13. Hydroabrasive resistance of plasma coatings of self-fluxing Ni-Cr-Si-B alloys in chloride solutions

    • V. M. Mikhalin
    • B. A. Slobodyanikov
    • S. V. Kotsot

    Quality, Reliability, and Durability Pages: 366 - 369

14. Comparative evaluation of the effectiveness of steels under hydrogen absorption conditions based on the results of short-term tensile tests

    • A. F. Nikolaev
    • V. V. Frolov
    • E. M. Chernykh

    New Materials and Corrosion Control Pages: 370 - 371

15. Adhesion of a rubberized coating to steel in a medium of penetrating acid

    • I. B. Gemusova
    • A. L. Shterenzon
    • Yu. E. Lobanov

    New Materials and Corrosion Control Pages: 372 - 375

16. Unit with aerodynamic heating of compressed air for vulcanization of rubberized coatings

    • V. A. Burak

    Equipment-Manufacturing Technology Pages: 376 - 377

17. Effectiveness of hardening threaded parts by plastic deformation

    • V. A. Pyshkin
    • S. V. Belai
    • I. G. Dyad'kova

    Equipment-Manufacturing Technology Pages: 378 - 383

18. Producing tube sheet holes for rolling of tubes

    • G. S. Belyaev
    • L. G. Tevelev

    Equipment-Manufacturing Technology Pages: 384 - 385

19. Reliability analysis of safety systems for gas-supply lines in the flame treatment of metals

    • V. I. Skvortsov

    Hygiene and Safety Engineering Pages: 386 - 389