Abstract
Poly-β-hydroxybutyrate (PHB) production from CO2 has the potential to reduce the production cost of this biodegradable polyesters, and also to make the material more sustainable compared to utilization of sugar feedstocks. In this study the unicellular cyanobacterium, Synechocystis sp. PCC 6714 has been identified as an unexplored potential organism for production of PHB. Synechocystis sp. PCC 6714 was studied under various cultivation conditions and nutritional limitations. Combined effects of nitrogen and phosphorus deficiency led to highest PHB accumulation under photoautotrophic conditions. Multivariate experimental design and quantitative bioprocess development methodologies were used to identify the key cultivation parameters for PHB accumulation. Biomass growth and PHB accumulation were studied under controlled defined conditions in a lab-scale photobioreactor. Specific growth rates were fourfold higher in photobioreactor experiments when cultivation conditions were controlled. After 14 days of cultivation in nitrogen and phosphorus, limited media intracellular PHB levels reached up to 16.4% from CO2. The highest volumetric production rate of PHB was 59 ± 6 mg L−1 day−1. Scanning electron microscopy of isolated PHB granules of Synechocystis sp. PCC 6714 cultivated under nitrogen and phosphorus limitations showed an average diameter of 0.7 µm. The results of this study might contribute towards a better understanding of photoautotrophic PHB production from cyanobacteria.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Introduction
Today, petroleum-based plastics are an essential part across all industries and have replaced glass and paper in packaging (Khanna and Srivastava 2005). Global plastics production reached around 322 million tonnes in 2015 (Plastics Europe 2016). Accumulation of these non-biodegradable plastics in the environment is a worldwide concern (Thompson et al. 2009), e.g. as microplastics in the marine environment. In this context, attention has been focused on research for the production of biodegradable plastics (Samantaray and Mallick 2015). Polyhydroxybutyrate (PHB) is the best-characterized member of the polyhydroxyalkanoate (PHA) family and is widespread in various bacterial species as storage material (Liebergesell et al. 1994; Steinbüchel 2008).
PHB is biodegradable (and compostable according to EN 13432), insoluble in water, non-toxic and biocompatible. Therefore, PHB could be an attractive alternative to petroleum-based plastics (Samantaray and Mallick 2015). It resembles the commodity polymer polypropylene in its properties (Lackner 2015). PHB is commercially produced by heterotrophic bacteria such as Alcaligenes eutrophus (Madison and Huisman 1999), Alcaligenes latus (Grothe and Chisti 2000) and recombinant Escherichia coli (Schubert et al. 1988). Despite relatively high yields of PHB, production from bacterial fermentation requires sugar supplementation and continuous oxygen supply which results in high substrate and operation costs (Steinbüchel 2008; Wu et al. 2001). In addition, public discussion about bioplastics production from sugar feedstocks is similar to the discussion about first generation biofuels. Competition of material with food and feed production for the same resources potentially leads to shortages and price increases causing poverty and is also contributing to climate change through direct and indirect land use change (Chen et al. 2017).
In order to compete with common plastics, cost reduction in PHB production is obligatory. This could possibly be achieved using cheap substrates such as whey, hemicellulose, and molasses (Alias and Tan 2005; Reddy et al. 2003). In this context, cyanobacteria are emerging as an alternative host system due to their minimal nutrient requirements and photoautotrophic nature (Samantaray and Mallick 2012). To date, PHB accumulation has been reported for a few cyanobacterial species with photoautotrophic PHB production reaching less than 10% of dry cell weight (dcw) (Bhati et al. 2010). The thermophilic cyanobacterial strain Synechocystis sp. MA-19 is the sole exception with accumulation of 27% (dcw) PHB reported (Miyake et al. 2000). A higher PHB content in cyanobacteria has only been detected in the case of heterotrophy or genetic modification of the strain; 29 and 41.6% (dcw) PHB were obtained in the presence of acetate and under P-deficiency in Synechocystis sp. PCC 6803 and Nostoc muscorum, respectively (Panda et al. 2006; Sharma et al. 2007).
The aim of this study was to quantitatively investigate the unicellular non-nitrogen fixing cyanobacterial strain Synechocystis sp. PCC 6714 for its ability to produce PHB. This strain has not been studied yet for PHB production but its recently published genome sequence (Kopf et al. 2014) showed a close relation to the widely studied model organism Synechocystis sp. PCC 6803 which has been extensively studied for PHB accumulation. Hence, the potential of PHB accumulation in Synechocystis sp. PCC 6714 was evaluated by shake flask experiments as well as bioreactor cultivations under defined conditions and the volumetric rates and productivities were evaluated. Additionally, growth behavior on different carbon sources as well as different cultivation conditions and their effect on biomass and PHB formation were investigated. Finally, the morphology of PHB granules has been studied using scanning electron microscopy (SEM). Advanced quantitative process development approaches including multivariate experimental design were used, aiming to provide a quantitative and consistent data-set to the scientific community.
Materials and methods
Strain and growth conditions
An axenic culture of wild-type strain Synechocystis sp. PCC 6714 was purchased from Pasteur Culture Collection of Cyanobacteria (Pasteur Institute, Paris, France). Unless stated otherwise, Synechocystis sp. PCC 6714 was grown in BG-11 medium (Rippka et al. 1979) supplemented with 10 mM HEPES buffer pH 8.5 and 5 mM NaHCO3 as carbon source prior to inoculation. In order to induce nitrogen deficiency, cells were cultured in BG-11 media without nitrate and ammonia. Ferrous ammonium citrate and Co (NO3)2·6H2O were substituted with equimolar concentrations of Ferric citrate and CoCl2·6H2O in terms of iron and copper content. For phosphorus limitation, KH2PO4 was replaced with an equimolar concentration of KCl in terms of potassium content (Panda et al. 2006).
The impact of acetate supplementation on PHB accumulation was studied by taking cells from their late exponential growth phase and transferring them into media without nitrogen or without nitrogen and phosphorus source and 5 mM acetate as substrate. PHB content was analyzed on 3rd, 7th, 14th and 16th day of incubation.
Cultivations were done in 500 mL Erlenmeyer flasks containing 100 mL medium at 28 ± 2 °C under continuous illumination with 50 ± 5 µmol photon m−2 s−1 in photosynthetically active radiation (PAR) in a shaking incubator (Infors, Switzerland) at 100 rpm agitation.
The impact of different carbon sources on biomass growth was studied in shake flask experiments under continuous illumination using BG-11 media and 5 mM of either carbonate, acetate, glucose or glycerol.
Growth determination and estimation of dry weight
Biomass growth was determined spectrophotometrically at 750 nm using a UV–Vis Spectrophotometer (Thermo Scientific, USA) at 24-h intervals. Dry Cell Weight (dcw) was determined in triplicates by transferring 10 mL of fermentation broth or shake flask cultures to a reusable pressure filter holder (Sartorius, Göttingen, Germany) and by filtering on a pre-weighed 0.45 µm Cellulose acetate filter paper (Sartorius, Göttingen, Germany) at a pressure of 6 bars for 1 min. Filters were dried overnight at 60 °C and dry weight was determined gravimetrically. A correlation between optical density and dcw could be established and described in Eq. (1)
Gas-exchange limitation or heterotrophy and nutrient limitations
Impact of gas exchange limitation (i.e. limitation of gas transfer to the culture vessel) was studied using cultivations on media without nitrogen or without nitrogen and phosphorus source in 150 mL anaerobic flasks plugged with rubber stoppers under three different illumination conditions, dark, light and dark/light cycle (16:8) h, respectively.
Design of experiments
Full factorial experimental design with three center points and data evaluation were carried out using MODDE (Umetrics, Sweden). For each selected response, MODDE generates a multiple linear regression (MLR) model with key parameters of R2 (coefficient of determination), Q2 (predictability), RP (reproducibility) and MV (model validity). The thresholds for R2, Q2, and RP were 0.5 for each parameter. Models with an MV value of >0.25 were considered to be significant.
Bioreactor cultivations
Bioreactor experiments were carried out under sterile conditions in a 1.5 L jacketed glass reactor with a working volume of 1 L (Applikon B.V, the Netherlands). The temperature was maintained at 28 °C and pH was measured with a pH-electrode (Mettler Toledo GmbH, Vienna, Austria) and was automatically maintained at 8.5 by the addition of 0.5 M HCl or 0.5 M NaOH. Agitation speed was at 300 rpm. Gas flow was controlled by mass flow controllers for air and CO2 (Brooks Instrument, Matfiels, USA). The reactor was bubbled with a mixture of sterile filtered air and 2% CO2 at a flow rate of 0.02 vvm (20 mL min−1). The illumination was done using LED strips wrapped around the reactor vessel providing a light intensity of 40 µmol m−2 s−1 photons in PAR. O2 and CO2 were measured in the off-gas with BlueSens gas sensors (BlueSens GmbH, Herten, Germany).
All fermentation parameters and variable pump set-points were controlled using the process information management system Lucullus online monitoring system 3.2 (Securecell AG, Schlieren, Switzerland).
Photobioreactor experiments were performed in duplicates and one is shown as an example. Samples were taken in triplicates at 24-h intervals and were analyzed for biomass, PHB content, and concentrations of macronutrients.
Determination of the PHB content
PHB quantification was done using the procedure described by Schlebusch and Forchhammer (2010) and Taroncher-Oldenburg et al. (2000). Pre-weighed dried cells (5–10 mg) were boiled with 1 mL conc. H2SO4 at 100 °C on a heating block (Accublock™, Labnet, USA) for one hour to convert PHB to crotonic acid. Samples were allowed to cool down and subsequently diluted 20 times using 0.014 M H2SO4. Crotonic acid was determined using a high-performance liquid chromatography system (Thermo-Fischer Scientific, USA) with a Nucleosil C8 column (Macherey–Nagel, Germany) using an isocratic method. The mobile phase used was 20 mM NaH2PO4 buffer; pH 2.5 and acetonitrile (70:30) with a flow rate of 0.85 mL min−1 and a column temperature of 30 °C. Detection of crotonic acid was done using a diode array detector (DAD) detector (Thermo-Fischer Scientific, USA) at 210 nm. For calibration, pure PHB (Sigma-Aldrich, USA) was treated accordingly and analyzed in parallel with samples. Instrument control and peak evaluation were done with Chromeleon 7.2 (Thermo-Fischer Scientific, USA). The percentage (dcw) PHB was determined with the amount of PHB obtained from HPLC analysis and the cell dry weight of biomass used for the analysis using Eq. (2):
Analysis of micronutrients
The concentrations of nitrogen (N), phosphorus (P), sulfur (S), and carbon (C) were measured using inductively coupled plasma-optical emission spectroscopy (ICP-OES) according to the modified method described previously by Nischkauer et al. (2014). For the analysis, samples were diluted (1:2) with 1% (v/v) hydrochloric acid and iridium was added as internal standard (final concentration 5 µg mL−1). Calibration solutions were prepared from the analytical grade salts of (sodium dihydrogen phosphate dihydrate for P, potassium nitrate for N, sodium sulfate for S, and sodium acetate for C). Samples and standards were analyzed with an iCAP 6000 ICP-OES instrument (Thermo Scientific, Germany). The optimized ICP parameters are given in Table 1. For each element three replicates were measured, two emission lines were monitored (for nitrogen, only one suitable line was available in the investigated spectral range), and quantitative results were calculated from both emission lines. The counts observed were converted into concentration units by means of external aqueous calibration. The response of the internal standard (Ir) was constant over each measurement session (5% relative standard deviation, no temporal trend), and no difference in Ir-response between samples and calibration standards was observed.
Analysis of PHB granules using scanning electron microscopy (SEM)
50 mL cyanobacterial cell suspension containing PHB granules was homogenized using Panda Plus homogenizer (GEA Group AG, Düsseldorf, Germany) for ten passages at 1500 bar pressure at room temperature. The homogenate was centrifuged at 10,000 rpm at 4 °C for 10 min. In order to remove pigments, the pellet containing PHB granules was washed with methanol. The cell pellet was subsequently harvested by centrifugation at 3000 rpm and resuspended in ultrapure water. 100 µL of an appropriate dilution of the suspension was transferred on a gold-sputtered (10–50 nm) polycarbonate filter (Millipore-Merck, Darmstadt, Germany) using reusable syringe filter holders with a diameter of 13 mm (Sartorius, Göttingen, Germany) and filtered using pressurized air. Gold-sputtered filters were washed with 200 µL of ultrapure water and fixed on a SEM sample holder using graphite adhesive tape and subsequently sputtered with gold to increase the contrast. SEM was performed using a QUANTA FEI SEM (Thermo Fisher, Waltham, MA, USA) with a secondary electron detector (SED). The acceleration voltage of the electron beam was set between 3 and 5 kV. The diameter of the PHB granules on SEM pictures was evaluated using the ImageJ plugin Fiji (Laboratory for Optical and Computational Instrumentation (LOCI), University of Wisconsin-Madison, WI, USA).
Results
Strain characterization
Impact of carbon sources on biomass formation
Initial characterization by shake flask experiments was done to gain a better understanding of cyanobacterial strain Synechocystis sp. PCC 6714. Different carbon sources, namely carbonate, acetate, glucose and glycerol were studied with respect to their impact on biomass growth.
As shown in Fig. 1 growth on carbonate reached a maximum biomass concentration of 1.4 ± 0.15 g L−1 after 14 days of incubation with an average specific growth rate (μaverage) of 0.095 ± 0.01 day−1 and a maximum specific growth rate (μmax) of 0.225 ± 0.02 day−1. Growth on acetate reached a maximum biomass concentration of 1.3 g L−1 after 14 days of cultivation with a μaverage of 0.09 ± 0.01 day−1 and a μmax of 0.2 ± 0.02 day−1, which are slightly lower when compared to growth on carbonate. Growth on glucose occurred with a μaverage of 0.107 ± 0.01 day−1 and a μmax of 0.28 ± 0.02 day−1 which is higher when compared to growth on carbonate and acetate. Growth on glycerol occurred with a lag phase of 250 h. After that, a μaverage of 0.09 ± 0.01 day−1 a biomass concentration of 0.72 ± 0.1 g L−1 was observed. This value was comparable with cultivations on carbonate and acetate. The results showed that Synechocystis sp. PCC 6714 can grow under different conditions ranging from fully autotrophic to heterotrophic growth conditions.
PHB formation in Synechocystis sp. PCC 6714
In order to study whether Synechocystis sp. PCC 6714 is able to accumulate PHB, cultivations under various nutrient limitations and continuous illumination were performed. The impact of the nitrogen source during growth (nitrate or ammonia), gas exchange limitation (GEL) and heterotrophy were studied under nutrient limitation. Experiments were carried out in two steps. After the growth phase on complete BG-11 media using nitrate or ammonia as a nitrogen source, limiting conditions were achieved by transferring cells to media without a nitrogen or without a nitrogen and phosphorus source, while using carbonate or acetate as substrate. Table 2 shows the PHB content obtained for Synechocystis sp. PCC 6714 under various limiting conditions. 7.5 ± 1% (dcw) PHB was obtained after 7 days of nitrogen limitation for cells previously grown on nitrate. This amount was further increased to 10 ± 1% (dcw) when cultivation was prolonged to 14 days. PHB content was higher when compared to cells previously grown on ammonia, where 9 ± 1% (dcw) were obtained after 14 days of limitation. After 16 days of nitrogen limitation in case biomass was grown on nitrate and acetate was the supplemented carbon source, 14.9 ± 1% (dcw) PHB was obtained. After 7 days of cultivation under nitrogen and phosphorus limitation, 8.2 ± 1% (dcw) PHB accumulation was detected and the highest PHB content of 13 ± 1% (dcw) was found after 14 days of limitation. The intracellular PHB level reached 15.5 ± 2% (dcw) after 16 days of incubation under nitrate and phosphate starvation when 5 mM acetate was supplemented. The PHB accumulation was higher for both nitrogen and nitrogen and phosphorus limitation when nitrate was used as nitrogen source. Gas exchange limitation under nitrogen and phosphorus limitation was done in order to study the effect of preventing an exchange of gas between the culture vessel and the environment on PHB accumulation. As shown in Table 2, a significant reduction in the PHB pool of Synechocystis sp. PCC 6714 was observed when the transfer of gas into the culture vessel was limited. The PHB content obtained was only 2.2 ± 1% (dcw) after 7 days of limitation and this amount was even further reduced when cultivation was prolonged to 14 days. Higher biomass concentrations were observed under nitrogen limitation than under nitrogen and phosphorus limitation. In addition, an insignificant increase in biomass concentration under GEL was observed.
Influence of cultivation conditions on PHB accumulation using a multivariate design of experiments (DoE)
In this study, the ability of Synechocystis sp. PCC 6714 to accumulate PHB was elucidated. The highest photoautotrophic PHB content of 13 ± 1% (dcw) was obtained under nitrogen and phosphorus limitation. To better understand the capability of the strain to produce biomass and PHB, the influence of temperature, pH, and CO2 availability was investigated. To that end, a full factorial design of experiments under nitrogen and phosphorus limitations was carried out. The experiments and the parameters are given in Table 3. It was hypothesized that PHB accumulation in strain Synechocystis sp. PCC 6714 is influenced by cultivation conditions. The two responses, biomass growth, and PHB accumulation after 14 days were determined and the results of the DoE were analyzed with MODDE.
First, the effect of the different factors on biomass formation was determined. As shown in Fig. 2a high CO2 concentration significantly reduced the biomass concentration. The model obtained showed that all three factors had a significant influence on the final biomass concentration. While higher CO2 concentrations and temperatures decreased biomass formation, higher pH values favored biomass formation. Within the borders of the experimental matrix, highest biomass concentration of 1.12 ± 0.12 g L−1 was found at 2% CO2, pH 10 and 25 °C.
a, c Represent the coefficient plots of the DoE experiments for Synechocystis sp. PCC 6714 under nitrogen and phosphorus limitation, for biomass concentration (a) and PHB accumulation (c), respectively. b, d Show the model parameters and observed-versus-predicted plots of the models obtained for biomass concentration (b) and PHB accumulation (d) under nitrogen and phosphorus limitation
Significant effects for the interaction terms CO2 * pH (increased biomass), CO2 * temperature (decreased biomass) and pH * temperature (decreased biomass) have also been obtained from the biomass model.
Next, the effect of the different factors on PHB accumulation was determined. As shown in Fig. 2c PHB accumulation was significantly reduced by increased CO2 concentrations, pH values, and temperatures. However, the effect was not significant for the pH value. Within the borders of the experimental matrix, highest PHB accumulation of 103 ± 10 mg L−1 (11 ± 1% dcw) was found at 2% CO2, pH 7 and 25 °C followed by an average PHB content of 10 ± 1% (dcw) at pH 8.5, 30 °C and 6% CO2.
The DoE was done under three different illumination conditions: dark, light and dark/light cycle (16:8 h), respectively. The results obtained showed both dark/light cycle and continuous illumination were suitable for PHB accumulation. No significant difference was observed between the results obtained for maximum PHB accumulation under dark/light cycle (100 ± 10 mg L−1, 10.5% dcw) and continuous illumination (103 ± 10 mg L−1, 11% dcw). Dark/light cycle was found stimulatory for biomass growth. Maximum biomass concentration obtained under dark/light cycle (1.30 ± 0.1 g L−1) was higher when compared to continuous illumination (1.12 ± 0.1 g L−1). Cells grown without light showed very little biomass growth (< 0.1 g L−1) and PHB accumulation (<1% dcw).
Photobioreactor cultivation of Synechocystis sp. PCC 6714
Based on the results of the design of experiments indicating favorable conditions for both biomass formation and PHB accumulation these two parameters were studied in photobioreactor cultivations. To that end, photoautotrophic cultivation of Synechocystis sp. PCC 6714 was established in a 1-L lab scale photobioreactor with the aim to determine whether defined cultivation conditions could improve biomass formation, specific growth rates, and PHB content. In addition, the impact of the nitrogen source on biomass growth was studied. The data from the design of experiments suggested different cultivation conditions for maximum biomass concentration and PHB accumulation under nitrogen and phosphorus limitations. To ensure suitable cultivation conditions for biomass formation and PHB accumulation, four photobioreactor cultivations with different pH set points (7, 8.5, 9 and 10) at 28 °C and 2% CO2 were done (data not shown). Highest biomass formation was observed at pH 8.5. Therefore, the following parameters of 2% CO2, pH 8.5 and temperature of 28 °C were used for all photobioreactor cultivations.
Figure 3 shows growth curves obtained for cultivations a) in photobioreactor and b) in shake flasks with either nitrate or ammonia as nitrogen source. The μaverage in photobioreactor cultivations was 0.672 ± 0.07 day−1 with a µmax of 0.792 ± 0.08 day−1 compared to μaverage of 0.168 ± 0.02 day−1 and µmax of 0.240 ± 0.02 day−1 in shake flasks cultivations. This represents a fourfold higher specific growth rate for Synechocystis sp. PCC 6714 under defined conditions in the photobioreactor compared to shake flask cultivations.
Cultivation of Synechocystis sp. PCC 6714 on two different nitrogen sources, nitrate and ammonia, under continuous illumination. Given are biomass concentration over time for a photobioreactor cultivations and b shake flask experiments. The values shown are the mean of three individual experiments, a single standard deviation is given as error bar
The obtained results suggest that both nitrogen sources, nitrate and ammonia, are suitable for cultivation of Synechocystis sp. PCC 6714 in a photobioreactor and could facilitate biomass growth.
PHB accumulation in the photobioreactor cultivations
A significant increase of specific growth rate could be successfully shown in photobioreactor runs compared to shake flask experiments. Thus, it was hypothesized that also PHB accumulation is increased in photobioreactor cultivations. Two step cultivations of Synechocystis sp. PCC 6714 were done for photoautotrophic production of PHB under nutrient limitations.
As shown in Fig. 4a biomass growth occurred in BG-11 media using nitrate as nitrogen source until 120 h with a µaverage of 0.38 ± 0.04 day−1. Limitation started when cells were harvested and transferred into media without nitrogen and phosphorus. Cell growth ceased after 200 h of cultivation although metabolic activity continued until the end of the process. PHB accumulation started at the early phase of the limitation and a PHB content of 8 ± 1% (dcw) after 6 days of limitation was obtained. PHB accumulated to an intracellular concentration of about 14 ± 1% (dcw) on day 9 and the highest PHB content was observed on day 15 of about 16.4 ± 2% (dcw). A decline in PHB content was detected after day 15. The maximum polymer content per volume of medium was 342 ± 30 mg L−1 PHB which corresponds to 14.6 ± 1% (dcw) on day 10 from CO2. The highest volumetric PHB production rate obtained was 59 ± 6 mg L−1 day−1.
Time course of growth and PHB accumulation under nitrogen and phosphorus limitation for photobioreactor cultivations of Synechocystis sp. PCC 6714 for a growth on nitrate b growth on ammonia. *The vertical bar represents the start of the limitation phase. The values shown are the mean of three individual experiments)
Figure 4b shows biomass growth occurred on BG-11 media and ammonia as nitrogen source under a photoautotrophic condition in a lab-scale photobioreactor. Growth occurred until 120 h with a µaverage of 0.36 ± 0.04 day−1. This value is lower when compared with cultivations with nitrate as a nitrogen source. The intracellular level of PHB at the starting point of the limitation phase was determined to be about 1% (dcw) which is higher than for the cultivation with nitrate. When ammonia was used as nitrogen source for growth, the maximum PHB content obtained under nitrogen and phosphorus limitation was 0.288 ± 0.3 mg L−1 PHB on day 19 which corresponds to 14 ± 1% (dcw) PHB. The highest volumetric PHB production rate with ammonia as nitrogen source was 51 ± 5 mg L−1 day−1.
Elemental analysis of macronutrients from photobioreactor samples
The concentrations of macronutrients nitrogen, phosphorus, sulfur and carbon were characterized in photobioreactor cultivations of Synechocystis sp. PCC 6714 under photoautotrophic growth conditions with nitrate as the nitrogen source. Elemental analysis of the culture supernatant showed uptake of nitrogen and phosphorus during the first 50 h of the growth phase (0–120 h) (Fig. 5a). Nitrogen concentrations reduced to below the detection limit (70 mg L−1) during the growth phase and remained below the detection limit until the end of the cultivation. Accumulation of carbon up to 6 ± 0.5 g L−1 in the culture supernatant was observed during both, the growth and limitation phase whereas no such accumulation of carbon was observed intracellularly. Uptake of small amounts of sulfur was detected both during growth and limitation phase. Figure 5b shows that the intracellular concentration of phosphorus increase during the first 25 h of the growth phase (0–120 h) and subsequently decreased until the limitation phase was started. During the limitation phase, the intracellular level of phosphorus remained almost constant. The intracellular concentration of carbon, nitrogen, and sulfur during both growth and limitation phase was below the detection limits.
Time course of residual macronutrient concentrations for nitrogen, phosphorus, sulfur, and carbon in photobioreactor cultivations of Synechocystis sp. PCC 6714 cultivated photoautotrophically and with nitrate as the nitrogen source is shown a in the culture supernatant b intracellular concentration of the macronutrients. *The vertical bar represents the start of the limitation phase. The values shown are the mean of three individual experiments, a single standard deviation is given as error bar
Size determination of PHB granules
Apart from quantitative determination of the PHB content, it was of interest to visualize PHB granules in this strain. To this end, scanning electron microscopy (SEM) was used to determine shape and size of the PHB granules extracted from Synechocystis sp. PCC 6714. Figure 6 shows a SEM image of PHB granules from the photoautotrophic cultivation of nitrogen and phosphorus limited cells. Image analysis of PHB granule using ImageJ plugin Fiji showed electron transparent particles with average diameter of 0.7 µm and maximum size of 0.95 µm. Cells cultured in complete BG-11 media were used as a control. They were homogenized and prepared the same way for analysis by scanning electron microscopy. For the unlimited control cells, no electron transparent particles were observed.
Discussion
Initial characterization
Initial strain characterization showed the flexibility of Synechocystis sp. PCC 6714 for utilization of different carbon sources for growth. Although growth on carbonate and acetate occurred with more or less the same µaverage 0.095 ± 0.01 day−1 for growth on carbonate (1.45 ± 0.1 g L−1) higher biomass concentration was detected when compared to acetate (1.25 ± 0.1 g L−1). This is in contrast to results which were shown for other cyanobacteria where acetate resulted in higher biomass concentrations (De Philippis et al. 1992). As it was expected, growth on glucose occurred at higher µaverage (0.107 ± 0.01 day−1) and the observation was in line with previous reports of Vermaas (1996) and Wang et al. (2002) where higher growth rates were detected for Synechocystis sp. PCC 6803 when glucose was used as the substrate.
PHB formation under nutrient limitations
In this study, photoautotrophic PHB accumulation in Synechocystis sp. PCC 6714 has been explored for the first time. Under photoautotrophic conditions and nitrogen limitation, a rise in PHB pool up to 10 ± 1% (dcw) was observed. Stimulation of PHB accumulation by nitrogen limitation has been previously explored by Lee et al. (1995) and (2005) where an increase in PHB accumulation under nitrogen limitation was ascribed to high intracellular concentrations of NADPH. Supplementation of acetate under nitrogen deficiency was found to be stimulatory for PHB accumulation in Synechocystis sp. PCC 6714. This has also been observed for other cyanobacteria. Wu et al. (2002) reported 15 ± 1% (dcw) PHB accumulation for Synechocystis sp. PCC 6803 when acetate was supplemented. Increase in PHB production by acetate supplementation has been explained by Dawes (1992) as the result of direct utilization of the substrate for polymer synthesis. Simultaneous limitations of nitrogen and phosphorus under photoautotrophy appeared to be a suitable stimulant for PHB accumulation since up to 16.4 ± 2% (dcw) PHB were detected under these conditions. These results are in line with earlier findings of Pal et al. (1998) and Nishioka et al. (2001) where it was shown that PHB accumulation could be increased by phosphate unavailability for Azotobacter chroococcum and Synechococcus sp. MA-19, respectively.
Limitation of gas exchange under nitrogen and phosphorus deficiency in Synechocystis sp. PCC 6714 reduced the intracellular PHB pool and biomass concentration significantly. This could be due to an inhibitory effect of oxygen caused by a build-up in the culture vessel. Oxygen competes with CO2 during photorespiration for ribulose-1, 5-bisphosphate carboxylase/oxygenase (RuBisCO) enzyme to convert CO2 to biomass (Raso et al. 2012). The findings from this study are in contrast with the results reported by Panda and Mallick (2007) which showed GEL can significantly boost PHB content in Synechocystis sp. PCC 6803. The different results of the two studies could be due to the different conditions used for the experiments.
Optimization of cultivation parameters
Key parameters influencing growth and PHB content in Synechocystis sp. PCC 6714 were identified using a multivariate design of experiments. It was found that biomass formation and PHB accumulation were a function of various cultivation parameters. Within the borders of the specified experimental matrix, the highest biomass concentration (1.12 ± 0.1 g L−1) and highest PHB accumulation (11 ± 1% dcw) were obtained at 2% CO2 concentration. This observation, however, is in contrast to earlier findings of Eberly and Ely (2012) where growth rates and accumulation of carbon storage compounds were enhanced with increased CO2 concentrations in the thermophilic cyanobacterium Thermosynechococcus elongatus. This difference in growth behavior might be due to lower CO2 solubility at 50 °C used for T. elongates compared to 28 °C used for Synechocystis sp. PCC 6714. Additionally, a temperature of 28 °C used for photobioreactor cultivations of Synechocystis sp. PCC 6714 was favorable for PHB accumulation. This is in line with previous observations of Panda et al. (2006) for Synechocystis sp. PCC 6803 where the temperature range of 28–32 °C was preferred for PHB accumulation.
Cultivations with either continuous illumination or dark/light cycles did not show a significant difference in PHB content. However, cells grown without light showed very little biomass growth and PHB accumulation.
Cultivation of cyanobacteria in the photobioreactor
Interestingly, photobioreactor cultivations of Synechocystis sp. PCC 6714 showed fourfold higher average specific growth rate when compared to shake flask cultivations. This observation is likely due to well-defined conditions in the photobioreactor compared to uncontrolled shake flask cultivations. It has been shown that under controlled conditions, growth rates and biomass concentration can be improved in microalgae cultivations (García-Malea et al. 2009; Ugwu et al. 2008). This underlines the importance of defined conditions to obtain highly productive processes (Pruvost et al. 2011). It has been shown biomass and lipid productivity in microalgae can be improved significantly under defined conditions of a photobioreactor.
It was observed that for photobioreactor cultivations using ammonia as the nitrogen source during the growth phase, Synechocystis sp. PCC 6714 already showed a PHB content of 1% (dcw) at the end of the growth phase. This suggests that the cells might have already been limited during the growth phase. One explanation for this phenomenon might be that the uptake of ammonia is affected by the pH-dependent equilibrium between NH3 and NH4 + and therefore might not be sufficiently available to the cells throughout the growth phase. Furthermore, it would be expected that uptake rates for ammonia are higher than for nitrate since ammonia can directly be utilized by the cell, whereas nitrate needs to be converted into ammonia first. Therefore, the energetic cost for the cell to take up ammonia is lower compared to nitrate (Dortch and Postel 1989; Syrett 1981). In the present study, higher growth rates and PHB contents were observed for cultivations with nitrate as nitrogen source compared to cultivations with ammonia as nitrogen source. This has been previously reported by Rückert and Giani (2004) where higher cell densities and a higher protein content was detected in Microcystis viridis when nitrate was used instead of ammonia or urea. In addition, high concentrations of ammonia have been shown to be toxic to some cyanobacteria (Drath et al. 2008), while no such toxicity has been reported for nitrate. Problems related to solubility and toxicity of ammonia could be overcome by implementing a continuous feeding strategy.
Potential of Synechocystis sp. PCC 6714 for photoautotrophic production of PHB
16.4% (dcw) PHB were obtained for Synechocystis sp. PCC 6714 from CO2. PHB content of 11–13% and 29% (dcw) are reported, respectively, in wild-type and genetically modified Synechocystis sp. PCC 6803 by Klotz et al. (2016) and Khetkorn et al. (2016). Also 27 and 23% (dcw) for Synechococcus sp. MA-19 and Nostoc muscorum, respectively, have been obtained (Nishioka et al. 2001; Sharma and Mallick 2005). However, total product concentration and volumetric rates for these strains have not been described and therefore it is challenging to evaluate the mentioned strains in terms of PHB productivity only based on the reported percentage of dry cell weights. In this respect, Wu et al. in (2001) reported total PHB concentration of 16 to 27 mg L−1 PHB for Synechocystis sp. PCC 6803. For Calothrix scytonemicola TISTR 8095 PHB content of about 25.4% (dcw) was reported with a total PHB concentration of 356 mg L−1 after 60 days of cultivation (Kaewbai-Ngam et al. 2016). In this study, the maximum polymer content per volume of the medium of 342 ± 34 mg L−1 PHB was observed after 10 days of limitation which corresponds to 14.6 ± 1% (dcw) PHB. The highest volumetric production rate of PHB observed was 59 ± 6 mg L−1 day−1. Available literature so far has not used this parameter, therefore our obtained value cannot be compared to other studies. Additional accumulation of a carbon-containing compound (up to 6 g L−1 of carbon) in the culture supernatant during photobioreactor cultivations of Synechocystis sp. PCC 6714 could be due to the formation of extracellular polysaccharides as previously reported by De Philippis and Vincenzini (1998). However, this observation requires further investigation.
In this study, the cyanobacterium Synechocystis sp. PCC 6714 has been reported as PHB producer for the first time. The results suggest Synechocystis sp. PCC 6714 to be suitable as a potential host strain for photoautotrophic PHB production. The specific growth rate, total PHB content and volumetric PHB production rate were increased significantly only by controlling process conditions in two-step batch cultivations in a photobioreactor. In order to obtain a robust process further optimization with respect to a suitable process strategy supporting both biomass formation as well as stable PHB production is required. A potential strategy that shall be further investigated is to optimize the media to provide nitrogen and phosphorus in a way that enables a one-step process without the need to exchange the media.
Abbreviations
- PHB:
-
polyhydroxybutyrate
- dcw:
-
dry cell weight
- SEM:
-
scanning electron microscopy
- SED:
-
scanning electron detector
- µaverage :
-
average specific growth rate
- µmax :
-
maximum specific growth rate
- PAR:
-
photosynthetically active radiation
- OD750 :
-
optical density at 750 nm
- GEL:
-
gas exchange limitation
- DoE:
-
design of experiment
- MLR:
-
multiple linear regression
- MV:
-
model validity
- R2 :
-
coefficient of determination
- Q2 :
-
predictability of a model
- RP:
-
reproducibility of a model
- ICP-OES:
-
inductively coupled plasma-optical spectroscopy
- Ir:
-
internal standard
- RuBisCO:
-
ribulose-1, 5-bisphosphate carboxylase/oxygenase
References
Alias Z, Tan IK (2005) Isolation of palm oil-utilising, polyhydroxyalkanoate (PHA)-producing bacteria by an enrichment technique. Bioresour Technol 96(11):1229–1234. doi:10.1016/j.biortech.2004.10.012
Bhati R, Samantaray S, Sharma L, Mallick N (2010) Poly-β-hydroxybutyrate accumulation in cyanobacteria under photoautotrophy. Biotechnol J 5:1181–1185. doi:10.1002/biot.201000252
Chen W-Y, Suzuki T, Lackner M (2017) Handbook of climate change mitigation and adaptation, 2nd edn. Springer, Berlin
Dawes EA (1992) Storage polymers in prokaryotes. In: Symposia-society for general microbiology. Cambridge University Press, Cambridge, p 81
De Philippis R, Vincenzini M (1998) Exocellular polysaccharides from cyanobacteria and their possible applications. FEMS Microbiol Rev 22(3):151–175. doi:10.1111/j.1574-6976.1998.tb00365.x
De Philippis R, Sili C, Vincenzini M (1992) Glycogen and poly-β-hydroxybutyrate synthesis in Spirulina maxima. Microbiology 138(8):1623–1628. doi:10.1099/00221287-138-8-1623
Dortch Q, Postel JR (1989) Biochemical indicators of N utilization by phytoplankton during upwelling off the Washington coast. Limnol Oceanogr 34(4):758–773. doi:10.4319/lo.1989.34.4.0758
Drath M, Kloft N, Batschauer A, Marin K, Novak J, Forchhammer K (2008) Ammonia triggers photodamage of photosystem II in the cyanobacterium Synechocystis sp. strain PCC 6803. Plant Physiol 147(1):206–215. doi:10.1104/pp.108.117218
Eberly JO, Ely RL (2012) Photosynthetic accumulation of carbon storage compounds under CO2 enrichment by the thermophilic cyanobacterium Thermosynechococcus elongatus. J Ind Microbiol Biot 39(6):843–850. doi:10.1007/s10295-012-1092-2
García-Malea MC, Acién FG, Del Río E, Fernández JM, Cerón MC, Guerrero MG, Molina-Grima E (2009) Production of astaxanthin by Haematococcus pluvialis: taking the one-step system outdoors. Biotechnol Bioeng 102(2):651–657. doi:10.1002/bit.22076
Grothe E, Chisti Y (2000) Poly (ß-hydroxybutyric acid) thermoplastic production by Alcaligenes latus: behavior of fed-batch cultures. Bioprocess Biosyst Eng 22(5):441–449. doi:10.1007/s004490050757
Kaewbai-Ngam A, Incharoensakdi A, Monshupanee T (2016) Increased accumulation of polyhydroxybutyrate in divergent cyanobacteria under nutrient-deprived photoautotrophy: an efficient conversion of solar energy and carbon dioxide to polyhydroxybutyrate by Calothrix scytonemicola TISTR 8095. Bioresour Technol 212:342–347. doi:10.1016/j.biortech.2016.04.035
Khanna S, Srivastava AK (2005) Recent advances in microbial polyhydroxyalkanoates. Process Biochem 40(2):607–619. doi:10.1016/j.procbio.2004.01.053
Khetkorn W, Incharoensakdi A, Lindblad P, Jantaro S (2016) Enhancement of poly-3-hydroxybutyrate production in Synechocystis sp. PCC 6803 by overexpression of its native biosynthetic genes. Bioresour Technol 214:761–768. doi:10.1016/j.biortech.2016.05.014
Klotz A, Georg J, Bucinska L, Watanabe S, Reimann V, Januszewski W, Sobotka R, Jendrossek D, Hess WR, Forchhammer K (2016) Awakening of a dormant cyanobacterium from nitrogen chlorosis reveals a genetically determined program. Curr Biol 26(21):2862–2872. doi:10.1016/j.cub.2016.08.054
Kopf M, Klähn S, Voss B, Stüber K, Huettel B, Reinhardt R, Hess WR (2014) Finished genome sequence of the unicellular cyanobacterium Synechocystis sp. strain PCC 6714. Genome Announc 2(4):e00757–e00814
Lackner M (2015) Bioplastics Kirk-Othmer encyclopedia of chemical technology. Wiley, New York
Lee IY, Kim MK, Chang HN, Park YH (1995) Regulation of poly-β-hydroxybutyrate biosynthesis by nicotinamide nucleotide in Alcaligenes eutrophus. FEMS Microbiol Lett 131(1):35–39. doi:10.1016/0378-1097(95)00231-S
Lee SY, Hong SH, Park SJ, van Wegen R, Middelberg APJ (2005) Metabolic flux analysis on the production of poly(3-hydroxybutyrate) biopolymers. Wiley, New York
Liebergesell M, Sonomoto K, Madkour M, Mayer F, Steinbüchel A (1994) Purification and characterization of the poly(hydroxyalkanoic acid) synthase from Chromatium vinosum and localization of the enzyme at the surface of poly (hydroxyalkanoic acid) granules. Eur J Biochem 226(1):71–80. doi:10.1111/j.1432-1033.1994.00t71.x
Madison LL, Huisman GW (1999) Metabolic engineering of poly(3-hydroxyalkanoates): from DNA to plastic. Microbiol Mol Biol Rev 63(1):21–53
Miyake M, Takase K, Narato M, Khatipov E, Schnackenberg J, Shirai M, Kurane R, Asada Y (2000) Polyhydroxybutyrate production from carbon dioxide by cyanobacteria. Appl Biochem Biotechnol 84(1):991. doi:10.1385/abab:84-86:1-9:991
Nischkauer W, Vanhaecke F, Bernacchi S, Herwig C, Limbeck A (2014) Radial line-scans as representative sampling strategy in dried-droplet laser ablation of liquid samples deposited on pre-cut filter paper disks. Spectrochim Acta B 101:123–129. doi:10.1016/j.sab.2014.07.023
Nishioka M, Nakai K, Miyake M, Asada Y, Taya M (2001) Production of poly-β-hydroxybutyrate by thermophilic cyanobacterium, Synechococcus sp. MA19, under phosphate-limited conditions. Biotechnol Lett 23:1095–1099. doi:10.1023/A:1010551614648
Pal S, Manna A, Paul A (1998) Nutritional and cultural conditions for production of poly-3-hydroxybutyric acid by Azotobacter chroococcum. Folia Microbiol 43(2):177–181. doi:10.1007/BF02816506
Panda B, Mallick N (2007) Enhanced poly-β-hydroxybutyrate accumulation in a unicellular cyanobacterium, Synechocystis sp. PCC 6803. Lett Appl Microbiol 44:194–198. doi:10.1111/j.1472-765X.2006.02048.x
Panda B, Jain P, Sharma L, Mallick N (2006) Optimization of cultural and nutritional conditions for accumulation of poly-β-hydroxybutyrate in Synechocystis sp. PCC 6803. Bioresour Technol 97:1296–1301. doi:10.1016/j.biortech.2005.05.013
Plastics Europe (2016) Plastics the Facts PUblisher. http://www.plasticseurope.org/Document/plastics-the-facts-2016-15787.aspx?FolID=2. Accessed 20 Mar 2017
Pruvost J, Van Vooren G, Le Gouic B, Couzinet-Mossion A, Legrand J (2011) Systematic investigation of biomass and lipid productivity by microalgae in photobioreactors for biodiesel application. Bioresour Technol 102(1):150–158. doi:10.1016/j.biortech.2010.06.153
Raso S, Van Genugten B, Vermuë M, Wijffels RH (2012) Effect of oxygen concentration on the growth of Nannochloropsis sp. at low light intensity. J Appl Phycol 24(4):863–871. doi:10.1007/s10811-011-9706-z
Reddy CSK, Ghai R, Kalia VC (2003) Polyhydroxyalkanoates: an overview. Bioresour Technol 87(2):137–146. doi:10.1016/S0960-8524(02)00212-2
Rippka R, Deruelles J, Waterbury JB, Herdman M, Stanier RY (1979) Generic assignments, strain histories and properties of pure cultures of cyanobacteria. Microbiology 111(1):1–61. doi:10.1099/00221287-111-1-1
Rückert GV, Giani A (2004) Effect of nitrate and ammonium on the growth and protein concentration of Microcystis viridis Lemmermann (Cyanobacteria). Braz J Bot 27(2):325–331. doi:10.1590/S0100-84042004000200011
Samantaray S, Mallick N (2012) Production and characterization of poly-β-hydroxybutyrate (PHB) polymer from Aulosira fertilissima. J Appl Phycol 24:803–814. doi:10.1007/s10811-011-9699-7
Samantaray S, Mallick N (2015) Impact of various stress conditions on poly-β-hydroxybutyrate (PHB) accumulation in Aulosira fertilissima CCC 444. Curr Biotechnol 4(3):366–372. doi:10.2174/2211550104666150806000642
Schlebusch M, Forchhammer K (2010) Requirement of the nitrogen starvation-induced protein Sll0783 for polyhydroxybutyrate accumulation in Synechocystis sp. strain PCC 6803. Appl Environ Microb 76(18):6101–6107. doi:10.1128/AEM.00484-10
Schubert P, Steinbüchel A, Schlegel HG (1988) Cloning of the Alcaligenes eutrophus genes for synthesis of poly-beta-hydroxybutyric acid (PHB) and synthesis of PHB in Escherichia coli. J Bacteriol 170(12):5837–5847. doi:10.1128/jb.170.12.5837-5847.1988
Sharma L, Mallick N (2005) Accumulation of poly-beta-hydroxybutyrate in Nostoc muscorum: regulation by pH, light-dark cycles, N and P status and carbon sources. Bioresour Technol 96(11):1304–1310. doi:10.1016/j.biortech.2004.10.009
Sharma L, Singh AK, Panda B, Mallick N (2007) Process optimization for poly-beta-hydroxybutyrate production in a nitrogen fixing cyanobacterium, Nostoc muscorum using response surface methodology. Bioresour Technol 98(5):987–993. doi:10.1016/j.biortech.2006.04.016
Steinbüchel A (2008) PHB and other polhydroxyalkanoic acids. Biotechnology set, 2nd edn. pp 403–464
Syrett P (1981) Nitrogen metabolism of microalgae. Can Bull Fish Aquat Sci 210:182–210
Taroncher-Oldenburg G, Nishina K, Stephanopoulos G (2000) Identification and analysis of the polyhydroxyalkanoate-specific β-ketothiolase and acetoacetyl coenzyme A reductase genes in the cyanobacterium Synechocystis sp. strain PCC6803. Appl Environ Microb 66(10):4440–4448. doi:10.1128/AEM.66.10.4440-4448.2000
Thompson RC, Moore CJ, Vom Saal FS, Swan SH (2009) Plastics, the environment and human health: current consensus and future trends. Philos Trans R Soc B Biol Sci 364(1526):2153–2166. doi:10.1098/rstb.2009.0053
Ugwu C, Aoyagi H, Uchiyama H (2008) Photobioreactors for mass cultivation of algae. Bioresour Technol 99(10):4021–4028. doi:10.1016/j.biortech.2007.01.046
Vermaas W (1996) Molecular genetics of the cyanobacterium Synechocystis sp. PCC 6803: Principles and possible biotechnology applications. J Appl Phycol 8(4):263–273. doi:10.1007/BF02178569
Wang Y, Li Y, Shi D, Shen G, Ru B, Zhang S (2002) Characteristics of mixotrophic growth of Synechocystis sp. in an enclosed photobioreactor. Biotechnol Lett 24(19):1593–1597. doi:10.1023/A:1020384029168
Wu G, Wu Q, Shen Z (2001) Accumulation of poly-β-hydroxybutyrate in cyanobacterium Synechocystis sp. PCC6803. Bioresour Technol 76(2):85–90. doi:10.1016/S0960-8524(00)00099-7
Wu G, Bao T, Shen Z, Wu Q (2002) Sodium acetate stimulates PHB biosynthesis in Synechocystis sp. PCC 6803. Tsinghua. Sci Technol 7(4):435–438
Authors’ contributions
DK, SP and CH planned the experiments, analyzed the data and wrote the manuscript. DK, WN and AL carried out the experiments, WN, AL and ML reviewed the manuscript. All authors read and approved the final manuscript.
Acknowledgements
Open access funding was provided by TU Wien, Vienna, Austria. The authors would like to thank “Vienna Business Agency” for funding this project.
Competing interests
The authors declare that they have no competing interests.
Availability of data and materials
The datasets supporting the conclusions of this article are included within the main article.
Funding
This work was supported by the “Vienna Business Agency”.
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Kamravamanesh, D., Pflügl, S., Nischkauer, W. et al. Photosynthetic poly-β-hydroxybutyrate accumulation in unicellular cyanobacterium Synechocystis sp. PCC 6714. AMB Expr 7, 143 (2017). https://doi.org/10.1186/s13568-017-0443-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/s13568-017-0443-9