Abstract
The aim of this work is to present a critical review on slurry bioreactors (SB) and their application to bioremediation of soils and sediments polluted with recalcitrant and toxic compounds. The scope of the review encompasses the following subjects: (i) process fundamentals of SB and analysis of advantages and disadvantages; (ii) the most recent applications of SB to laboratory scale and commercial scale soil bioremediation, with a focus on pesticides, explosives, polynuclear aromatic hydrocarbons, and chlorinated organic pollutants; (iii) trends on the use of surfactants to improve availability of contaminants and supplementation with degradable carbon sources to enhance cometabolism of pollutants; (iv) recent findings on the utilization of electron acceptors other than oxygen; (v) bioaugmentation and advances made on characterization of microbial communities of SB; (vi) developments on ecotoxicity assays aimed at evaluating bioremediation efficiency of the process.
From this review it can be concluded that SB is an effective ad situ and ex situ technology that can be used for bioremediation of problematic sites, such as those characterized by soils with high contents of clay and organic matter, by pollutants that are recalcitrant, toxic, and display hysteretic behavior, or when bioremediation should be accomplished in short times under the pressure and monitoring of environmental agencies and regulators. SB technology allows for the convenient manipulation and control of several environmental parameters that could lead to enhanced and faster treatment of polluted soils: nutrient N, P and organic carbon source (biostimulation), inocula (bioaugmentation), increased availability of pollutants by use of surfactants or inducing biosurfactant production inside the SB, etc. An interesting emerging area is the use of SB with simultaneous electron acceptors, which has demonstrated its usefulness for the bioremediation of soils polluted with hydrocarbons and some organochlorinated compounds. Characterization studies of microbial communities of SB are still in the early stages, in spite of their significance for improving reactor operation and design optimization.
We have identified the following niches of research needs for SB in the near and mid term future, inter alia: (i) application of SB with sequential and simultaneous electron acceptors to soils polluted with contaminants other than hydrocarbons (i.e., pesticides, explosives, etc.), (ii) evaluation of the technical feasibility of triphasic SB that use innocuous solvents to help desorbing pollutants strongly attached to soils, and in turn, to enhance their biodegradation, (iii) gaining deeper insight of microbial communities present in SB with the intensified application of molecular biology tools such as PCR-DGGE, PCR-TGGE, ARDRA, etc., (iv) development of more representative ecotoxicological assays to better assess the effectiveness of a given bioremediation process.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.1. Introduction
Bioremediation is an alternative that offers the possibility to destroy toxic pollutant using natural biological activity. By definition, bioremediation is the use of living organisms, primarily microorganisms, to degrade the environmental contaminants into less toxic forms. It uses naturally occurring bacteria and fungi or plants to degrade or detoxify substances hazardous to human health and/or the environment [1]. The microorganisms may be indigenous to a contaminated area or they may be isolated from elsewhere and brought to the contaminated site. Contaminant compounds are transformed by living organisms through reactions that take place as a part of their metabolic processes. Biodegradation of a compound is often a result of the actions of multiple organisms. When microorganisms are imported to a contaminated site to enhance degradation we have a process known as bioaugmentation [2]. Bioremediation techniques are typically more economical than thermal and physico-chemical remediation such as incineration [3, 4].
Bioremediation processes have been classified in three broad categories, according to place and soil handling/conditioning: in situ, ad situ, and ex situ. The second and third class of processes are useful for the remediation of (1) sludges, soils or sediments polluted with high concentration of recalcitrant contaminants [5], for instance polynuclear aromatic hydrocarbons [6–9], diesel [10, 11], explosives [12], pesticides and chlorinated organic pollutants [13, 14], oily sludges from the petrochemical industry [15]; (2) clayish and stratified soils with low hydraulic conductivity and low permeability accompanied with high contents of organic matter [13, 16]; and (3) soils in regions and areas where environmental conditions are adverse to biological processes, for instance, low temperature that negatively affects biodegradation rates [17], and (4) contaminated sites that require a short remediation time because of regulatory or other pressures [18–20].
Slurry bioreactors are one of the most important types of ad situ and ex situ technique. Treatment of soils and sediments in slurry bioreactors has become one of the best options for the bioremediation of soils polluted by recalcitrant pollutants under controlled environmental conditions [17, 21, 22]. SBs are also very often applied to determine the feasibility and actual potential of a biological strategy in the final restoration of a contaminated soil or site [8, 11, 14]. In fact, under slurry conditions, the pollutant depletion rates depend mainly on the degradation activity of the microorganisms available in the system [20] and the results obtained generally reflect the actual biological depuration potential of the soil [23–28].
The objective of this paper is to present a critical review on slurry bioreactors (SBs) and their application to bioremediation of polluted soils and sediments. The scope of the review encompasses the following subjects: (i) process fundamentals of SB and analysis of advantages and disadvantages; (ii) the most recent applications of SB to laboratory scale and commercial scale soil bioremediation, with a focus on pesticides, explosives, polynuclear aromatic hydrocarbons, and chlorinated organic pollutants; (iii) trends on the use of surfactants to improve bioavailability of contaminants and supplementation with biodegradable carbon sources to enhance cometabolism of pollutants; (iv) recent findings on the utilization of electron acceptors other than oxygen; (v) advances made in characterization of microbial communities of SB; (vi) developments on ecotoxicity assays aimed at evaluating bioremediation efficiency of the process.
2. Process fundamentals and analysis of advantages and disadvantages of slurry bioreactors
Slurry bioreactor technology is an engineered complex that generally comprises four parts: installations for polluted soil handling and conditioning, the bioreactor battery itself, installations for treated soil handling and disposal, and ancillary equipment for treatment of process by-streams [18, 20]. The SB can be classified as batch, semi-continuous, and continuous from the operation point of view. The most common operational mode is batch. Another useful classification relies on the main electron acceptor used in the biodegradation process: aerobic (molecular oxygen), anoxic (nitrate and some metal cations), anaerobic (sulfate-reducing, methanogenic, fermentation) [13], and mixed or combined electron acceptors [29–31]. By far, aerobic SBs have predominated in full scale applications, although anaerobic SBs are an emerging area of research and development [21].
Interesting and distinctive features of SBs are that soil is treated in aqueous suspension, typically 10 to 30% w/v and that mechanical or pneumatic mixing is provided. These characteristics, in turn, lead to several process advantages, inter alia: (i) increased mass transfer rates and increased contact microorganisms/pollutant/nutrients; (ii) increased rates of pollutant biodegradation compared to in situ bioremediation or to ad situ solid phase biotreatment: (iii) associated to (i) and (ii), significantly shorter treatment times can be achieved; (iv) possibility of using different electron acceptors (O2, SO4-2, CO2, NO3-); (v) control and optimization of several environmental parameters such as temperature, pH, etc.; (vi) effective use of biostimulation and bioaugmentaion; (vii) increase pollutant desorption and availability through the addition of surfactants and solvents [2, 10, 12, 13, 32].
However, SBs also have a few disadvantages, all of them related to requirements for soil excavation, handling, and conditioning, and bioreactor construction/operation that typically increase treatment costs compared to most simple bioremediation techniques [20]. In spite of this, SBs has resulted more cost effective than incineration, solvent extraction and thermal desorption in many cases [33].
2.1 Process description
In SB, soil is excavated and conditioned and loaded into bioreactors [17, 34]. A main feature of SB is that soil inside reactor is kept in aqueous suspension by some type of mixing in a way that biological treatment is carried out under saturated conditions [18] and nearly homogeneous suspension [17] (See Figure 1).
There are several bioreactor configurations [20, 21]. At full scale, low cost bioreactors may consist of large lined lagoons (24 m × 15 m). Manufactured bioreactors can range 3 to 25 m diameter and 4.5 to 8 m height, with capacities between 60 to 1000 m3 [12, 18, 19]. Bioreactors are usually fitted with mixing devices, and aerobic SB are equipped with spargers or diffusers. Ancillary equipment may include gas emissions conduits and treatment, vessels for nutrient and pH conditioning of slurry, etc.
Main operating modes of SB include batch and semi-continuous. Continuous SB are possible in principle, but are not very common. Batch and semi-continuous reactors adapt easily to the handling of soils and slurries [18, 35], sometimes are operated in sequencing batch reactors [5, 20, 21].
2.2 Soil pretreatment
As it was mentioned above, one of the limitations of SBs technology is the requirement of soil excavation and pre-treatment. Usually, pretreatment consists of crushing followed by screening. The coarser fractions of soils (pebbles and sands, 0.85 to 4 mm) are discarded and sent to direct disposal, whereas fine fractions (clay and organic matter, < 0.85 mm) are retained and loaded into bioreactors. It is generally recognized that pollutants concentrate in fine particles of soil [16, 19].
2.3 Solids concentration
Polluted, fine fractions of soils are mixed with water or wastewater to form slurry with a concentration in the range between 15 to 60% w/v, depending on characteristics of soil and degradation rates determined in previous laboratory or pilot scale studies [20, 21]. Solids concentration is a key variable that might determine the mixing power required, aeration efficiency in aerobic SB, and the size of by-stream post-treatment installations [18]. It is a common practice to use decanted spent liquors from previous batch runs as water for making the slurries, as a method to minimize liquor treatment and disposal.
2.4 Mixing
SBs are provided with mixing devices in order to keep solids in suspension during biotreatment, as well as intensifying turbulence and thus increasing mass transfer rates [21]. There are several types of mixing devices, mechanical and pneumatic ones are the predominant among aerobic SBs. Also, mixing can be intermittent or continuous. The first leads to significant savings on power expenses, although mixing intensity is lower.
Mixing intensity is a critical factor in SB design and performance [21]. Its main role is to keep solid particles in suspension and provide slurry homogeneization, to help achieving a satisfactory aeration in aerobic SBs, and to increase several mass transfer rates such as desorption of pollutants from soil, among others. This, in turn, usually translates in higher rates of contaminant biodegradation, in particular when difficult-to-degrade xenobiotic compounds such as PCBs have to be removed [14]. Mixing selection and sizing mainly depends on slurry characteristics and kinetic requirements. Pilot studies and semi-empirical methods are usually required. Independently of the type of mixer selected, mixing power is of major concern because of its influence on the operating costs. The denser the slurry, the higher the power and more difficult to achieve oxygen transfer in aerobic SBs [19, 34]. So, several trade-offs have been recommended to keep power expenses at bay, such as intermittent mixing and slurry dilution [18].
2.5 Control of environmental conditions in the operation of slurry bioreactors
One distinctive and advantageous feature of SBs is the manipulation and control of environmental conditions that leads to biodegradation optimization and better process performance [17, 21, 35]. In this regard, several operational variables can be monitored and controlled: pH, dissolved oxygen in aerobic SBs, concentration of inorganic nutrients, pH is usually kept in the range 6.75–7.25 using either alkalis such as NaOH or acids such as H2SO4. Temperature range is 25–30°C, although SBs have been reported to successfully perform at lower ambient temperatures. Ideal dissolved oxygen concentration is 90% of the saturated dissolved concentration. Nitrogen and phosphorus salts are used as inorganic nutrient sources in order to ensure that there is no nutrient limitation (NH4Cl, KH2PO4, Na2HPO4) [5, 17, 36].
3. Applications of aerobic slurry bioreactors to bioremediation of soils polluted with pesticides, organo-chlorinated substances, explosives, and polynuclear aromatic hydrocarbons
Application of aerobic SBs (A-SB) to bioremediation of soils is still predominant. Aerobic degradation of organic pollutants is carried out by its oxidation via oxygenases or dioxygenases, so, molecular oxygen is usually a limiting factor [37]. A large number of laboratory, pilot and full scale studies and cases of A-SB can be found in the literature. In Tables 1, 2 and 3 we have excerpted some applications of A-SB to bioremediation of soils polluted with PAHs, pesticides and PCBs, and explosives, respectively.
Jee et al. [38] studied the bioremediation of sediment contaminated by 88 mg/kg phenanthrene. The influence of different solid/sediment loads and mixing conditions on the time course of the process was investigated. Under well mixed conditions, phenanthrene was removed by 25 to 40% during the first few days of treatment by showing an activity which decreased markedly from the 3rd to the 5th day. In unmixed systems, the extent of mineralization was notably lower, ranging from 5 to 20%. The pollutant mineralization did not cease by end of the 7th day of treatment. Under well mixed conditions, the reactors with a 10% sediment load showed the highest level mineralization. Pollutant mineralization yields achieved in the reactors with 5 and 15% sediment were similar, and lower than those attained with 10% sediments. In the unmixed reactors, the 10 and 15% solids loaded reactors showed similar activity.
Dean-Ross [39] conducted a A-SB bioremediation batch experiment on a pristine sediment spiked with phenanthrene, anthracene, pyrene and fluoranthene. PAHs, each added at 60–70 mg/L, disappeared after 6 to 8 days of treatment. Bioaugmentation with Rhodococcus sp. resulted in enhanced bioremediation rates and yields.
Villermur et al. [40] used a three 3-phase (two liquid phases + soil, TLP) aerobic slurry system containing silicone oil at 30% v/v to biodegrade selected high molecular weight PAHs spiked into a soil at 196 mg pyrene/kg, 192 mg chrysene/kg, and 163 mg benzo [a]pyrene/kg. Pyrene was degrade d through a rate of 19 mg/(L day) whereas the degradation rates of chrysene and benzo [a]pyrene were, 3.5 and 0.94 mg/(L day), respectively.
Wang & Vipulanandam [9] observed the effect of naphtalene concentration on the A-SB remediation potential. Naphthalene was generally found to rapidly desorb from the spiked soil by undergoing rapid and extensive biodegradation. 500 mg/kg of naphthalene were reduced to 20 mg/kg after 65 h days of treatment whereas 5000 mg/kg of the same pollutants were reduced to 40 mg/kg after 100 h.
Castaldi [33] treated petroleum waste sludges containing 680 mg/Kg of 2–3 ring PAHs and 38 mg/kg of 4–6 ring PAHs in a continuous flow multistage A-SB that operated at relatively short residence times with minimal loss of volatiles constituents. The higher molecular weight PAHs, including the four-ring derivatives of pyrene, benzo [a]pyrene, and chrysene, were removed with efficiencies greater than 90%.
Rutherford et al. [41] treated in a A-SB two different soils (a sandy soil and a silty clay one) contaminated with creosote compounds in the range 10 000 to 20 000 mg/kg. Unexpectedly, the extent of PAHs removal over 10 weeks was higher in the clay soil (43%) than in the sandy one (25%).
De Jonge & Verstrate [42] reported 70% removal from a soil initially polluted with up to 3 000 mg/kg of oil in A-SBs. Also, soils heavily contaminated with crude oil (200 g TPH/kg) could be treated in pilot A-SBs reaching 1 to 2 g TPH/kg in 5–7 weeks of treatment [43].
Castaldi & Ford [15] reported 73% removal of PCBs in 90 days of A-SB treatment of petrochemical waste sludges polluted with 115 mg/kg of PCBs. Bioremediation of sediments contaminated with 88 mg phenanthrene/kg in batch A-SB showed removal percentages of 25–50% in 7 days of operation [36]. On the other hand, Mueller et al. [17] observed the extensive removal (up 98%) of pentachlorophenols and creosote from soils and sediments in 30 days of operation. A soil spiked with a mixture of PAHs (270 mg/kg), composed by fluorene, phenanthrene, anthracene and pyrene, was treated in a batch A-SB for 20 days: fluorene and phenathrene were found to be removed by 70% and 40% after 3 days of incubation [16]. In another work with soil polluted with PAHs, Lewis [44] reported a removal of 70–97% of spiked PAHs (728 – 4 920 mg/kg) in 60 days of treatment.
Pinelli et al. [8] studied the intrinsic depuration capability of a soil historically contaminated by PAHs (overall initial PAHs: 3.7 g/kg) by using different aerobic batch bioreactors: a SB, a blade agitated bioreactor and a rotary vessel bioreactor. The performance of each bioreactor was evaluated by analyzing the disappearance of 14 target PAHs and of the total extractable organic matter of the soil. About 72, 96 and 95% of the total amount of PAHs initially present in the soil were removed in the SB, blade agitated semisolid-phase bioreactor, and rotatory vessel semisolid-phase bioreactor after 17, 47, and 35 days of treatment, respectively. Among the three treatments, SB was capable of inducing the readiest and fastest removal of the soil PAHs.
Fava et al. [11] treated an actual site historically contaminated soil containing about 13 g/kg of a large variety of PAHs in laboratory scale A-SB amended with soya lecithin or humic substances at 1.5% w/w. After 150 days of incubation of a room temperature, about 60% of original amount of PAHs was biodegraded with a marked reduction of the original soil ecotoxicity.
A-SBs have also been successfully applied to bioremediation of soils contaminated with pesticides. Cookson [20] reported that levels of pesticides in soils polluted with mixtures of 2,-4-dichlorophenoxy acetic acid (2,4-D), 4-chloro-2-methyl-phenoxy acetic acid, alachlor, trifuralin and carbofuran could be reduced from 800 to 20 mg/kg after two weeks of treatment. Robles-González et al. [30] carried out laboratory scale experiments with batch A-SB for bioremediation of an agricultural soil with high contents of clay and organic matter and polluted with 300 mg 2,4-D/kg. They observed removals of 2,4-D higher than 95% after 14 days of treatment; no chlorophenol intermediates of 2,4-D degradation were detected. Bachman et al. [27] reported 90–100% mineralization of α-hexachlorocyclohexane (HCH) from a soil initially polluted with 400 mg α-HCH/kg after 42 days of batch incubation of laboratory scale A-SB.
SBs also provided excellent results in the aerobic bioremediation of actual site PCBs-contaminated soils. Fava and co-workers [45, 46] reported of the efficient bioremediation of an actual site soil with 350 mg/kg of total PCBs through 141 days of A-SB treatment. They also demonstrate the possibility of enhancing the process through the SB supplementation with cyclodextrins (CDs) or the phytogenic surfactant Quillaya Saponin at 10 g/L. The opportunity to improve the aerobic slurry-phase bioremediation of another actual site soil lacking indigenous specialized bacteria and contaminated by 1547 mg/kg of PCBs through (a) soil bioaugmentation with the PCB mineralizing three-member bacterial coculture ECO3 [47] or (b) improvement of SB configuration [14] was successively investigated and demonstrated by the same authors.
Rattan et al. [48] found that batch soil slurry microcosms inoculated with a strain of Pseudomonas putida coexpressing cytochrome p-450 cam and luciferase, removed more than 65% of γ-HCH (105 mg/L slurry) after 4 weeks of incubation. On the other hand, less than 15% was the γ-HCH depletion achieved in the parallel non-inoculated controls.
Hudak & Cassidy [49] treated an aged contaminated soil in SB; lubricating oil (LO) and polychlorinated biphenyls (PCBs) were the pollutants applied at the concentration of ~11 400 mg/kg and ~1200 mg/kg, respectively. They also examined biosurfactant production by Pseudomonas aeruginosa. Rhamnolipid production was observed within 1 to 2 days after nitrogen depletion. By day 6, total rhamnolipid concentrations increased from below detection to average values over 1 000 mg/L, which was associated to removals over 98% of soil-bound PCBs and over 99% of total petroleum hydrocarbons.
Mohan et al. [22] studied the degradation of a di-ethyl phthalate (DEP) contaminated soil in a sequencing A-SB; the effect of bioaugmentation using effluent treatment plant (ETP) microflora on the degradation of DEP was also investigated. Consistent desorption of DEP was observed in the aqueous phase with increase in the contact time (cycle period) due to prevailing agitation in the reactor. Reactor operated with native soil microflora (7.6 × 103 CFU/g) and exhibited a maximum DEP degradation of 47.9%. Initially, up to 8 h of the cycle operation, the degradation of DEP in soil was found to be 9.85% and reached a maximum of 47.9% in 40 h. Another reactor was operated in the presence of ETP-degrading microflora (2.4 × 107 CFU/ml) without native soil microflora. Within 8 h of cycle operation a DEP degradation of 22.45% was noticed and reached a maximum of 75.4% at the end of cycle period. It was concluded that bioaugmentation with ETP-acclimated biomass significantly increased DEP removal.
Zhang et al. [5] have conducted pilot scale studies on bioremediation with A-SB of soils contaminated with explosives. They treated two soils from a former ammunition manufacturing plant, polluted with 14715 mg/kg to 1125 mg/kg of 2,4-dinitrotoluene (2,4-DNT) and 8940 mg/kg to 4800 mg/kg of 2,6-dinitrotoluene (2,6-DNT). Almost complete removal of explosives could be achieved in a short 2 days period. Moderate removal of 40% was reported for a soil polluted with 570 mg/kg of 2,4-DNT and 380 mg/kg of 2,6-DNT [50]. Laboratory scale experiments with A-SB showed an effective removal of explosives (90%) from soils with initial 400–1200 mg TNT/kg after 130 days of treatment [12].
4. Utilization of electron acceptors other than oxygen
Recent research has shown that non aerobic bioremediation holds promise for remediation of specific recalcitrant and toxic contaminants (such as organo-chlorinated pesticides and compounds, nitro-organics, etc.) where soils are rich in sulfate, nitrate, or bicarbonate [13, 30, 51–54].
Very often, non aerobic bioremediation is also preferable when anaerobic or reducing conditions predominate in the contaminated sites. In such scenarios, anaerobic bioremediation may be desirable whenever the pollutants are amenable to reductive dechlorination or nitro-reduction as first step to final biodegradation. Another advantage of anaerobic remediation is associated to savings of aeration (both investment and operating costs of aeration) [29, 30].
Reported studies on anaerobic bioremediation of soils and/or sediments in SB are still scarce. Table 4 summarizes a selection of recent research published in the open literature. Boopathy [29] treated a soil contaminated with 550 mg diesel/kg in several anoxic and anaerobic batch, laboratory scale SB. He found the highest removal of 80% in a SB with "mixed" or combined electron acceptors (SO4=, NO3-, CO2). One electron acceptor-SB showed lower removals, for instance, 55% of diesel removal was observed in the sulfate-reducing SB. Soils polluted with 1500 mg TNT/kg have been treated in batch, pilot scale anaerobic SB; up to 95% removal of TNT was reported [55].
Bachman et al. [28] tested aerobic and several laboratory scale anaerobic SB for the bioremediation of a coarse soil polluted with 400 mg α-HCH/kg. They reported 90 to 100% mineralization of the pesticide after 100 days of treatment in the A-SB, 85% in the methanogenic SB, whereas in the sulfate-reducing and denitrifying SB no conversion of HCH was observed. A 95% removal of Dinoseb (2-sec-buthyl-2,6-dinitrophenol) in methanogenic conditions was obtained from a soil contaminated with 800 mg/kg of this herbicide [55]. Robles-González et al. [30] conducted laboratory scale experiments with batch sulfate-SB for bioremediation of an agricultural soil with high contents of clay and organic matter and polluted with 300 mg 2,4-D/kg. They observed removals of 2,4-D near to 50% after 30 days of treatment and they detected chlorophenol intermediates of the anaerobic transformation of 2,4-D.
5. Use of surfactants and solvents to improve availability of contaminants
5.1 Advances on hysteresis characterization
Hysteresis coefficient is used for determining the adsorption-desorption behavior of pollutants on sediments and soils. In soil and sediment pollution, the adsorption and desorption play a key role on pollutants availability and transport. For several pollutants and solid matrices, the desorption pathway is different from that of adsorption. This phenomenon is known as hysteresis. Poggi-Varaldo et al. [56] have defined a hysteresis coefficient CH as the ratio of the slope (derivative) of the adsorption curve and the slope of the desorption curve in a given point (Cj, qj) of interest. When hysteresis is not important, CH ≅ 1, i.e., the adsorption is reversible, when hysteresis is important, then CH >1, i.e., the adsorption is irreversible. Among several uses of the CH, it can be cited the following: quantification of the effect of aging on the availability of a pollutant adsorbed onto sediments or soils; quantitative comparison of the degree or retention of a pollutant in several types of solid matrices; quantification of the effect of adding surfactants and solvents to a given system pollutant-solid matrix; quantitative comparison of the degree or retention of several pollutants in a given sediment or soil; and estimation of the retardation factor of transport of contaminant in porous, adsorbent media [31, 56].
The availability enhancement factor (AEF) is used for determining the effectiveness of desorption treatments of pollutants from soils and sediments. The AEF was defined as the ratio of the slope of the desorption curve of a given pollutant with a surfactant or solvent treatment to the slope of the corresponding curve of the reference treatment (usually desorption with distilled water). This factor has proved to be useful for the quantification of the effect of a given soil treatment (with surfactant, biosurfactant, solvents) on the possible improvement of the pollutant desorption and availability for further biodegradation or physicochemical removal [57].
5.2 Surfactants
Surfactants may facilitate hydrophobic pollutant desorption from a solid matrix, and its dispersion in the aqueous phase. They may also help in stabilizing the slurry soil-aqueous medium in the SB. Surfactants are classified as anionic (SDS, LASA and SDOSS), cationic (benzyl trimethyl-ammonium bromide) and non ionic (Triton X-100; Brij 35; Tergitol NP-10, Tween-80, etc.) from the point of view of predominant electric charge after contact with water [58, 59]. They can also been classified as synthetic and biological surfactants, according to its origin or production. The first ones are mainly manufactured by petrochemical plants, whereas the second ones are produced by living organisms. Examples in the second category are rhamnolipids, glycolipids or lipoproteins, among others [60–65].
Main factors that determine surfactant success and capability are its chemical nature and concentration as a multiple of critical micellar capacity (CMC). For synthetic surfactants, it has been observed that although they may be very effective for increasing the detachment of pollutants from soils, they usually become toxic to microbes at the high concentrations required for their action; very often pollutant degradation is adversely affected [35, 36, 64, 66, 67]. Results on surfactant capability and performance in the literature has been obscured by experimental designs that have not taken into account the surfactant CMC [58]. In this way, several works report no effect or negative effect of surfactants on pollutant mobilization and detachment from the solid matrix. Closer examination of a large amount of these experiments have revealed that surfactants were used at concentrations lower than their corresponding CMCs. Now it is generally recognized that surfactants should be added at a concentration higher than its CMC in order to effectively disperse and pseudo-solubilize the hydrophobic pollutant in water.
Regarding synthetic surfactants, the order of preference generally accepted is: non ionic > anionic > cationic. Cationic surfactants are usually toxic to microorganisms and also they can adsorb to negatively-charged sites of the clay and organic matter of the soil, reducing the actual concentration value. So, it is recommendable not only to carry out in vitro studies for determining surfactant capability [57] but inhibition studies of the candidate surfactants on the active microflora of the SB as well [68].
Biodegradable surfactants and biosurfactants may be the choice for increasing pollutant availability while minimizing inhibitorial effects on SB microflora. Yet, some biodegradable surfactants can compete with the pollutant as carbon source for the microorganisms provoking a preferential degradation of the surfactant and a lower removal of the contaminant [35, 36, 67, 69]. Microbial surfactants have proved to be able to combine excellent hydrophobic pollutant-mobilizing properties with other special features, rarely displayed by commercial chemical surfactants, such as complete biodegradability and non-toxicity [62, 65]. Unfortunately, little is very often known about their chemical-physical properties, and they are still not available on the large scale at low price, and this currently precludes their application in bioremediation. It has been recently shown that some commercial mixtures of biogenic compounds, such as cyclodextrins, phytogenic surfactants of water-soluble fraction of humic substances, can markedly intensify the bioremediation of PCB-, PAH- and/or hydrocarbon-contaminated soils in SBs (Tables 1 and 2) by displaying the same advantages showed by microbial surfactants. In particular, Fava and co-workers [45, 46] demonstrated that two cyclodextrins (CDs), i.e., hydroxypropyl-β-CD and γ-CD, and the phytogenic surfactant Quillaya Saponin were able to enhance from 15 to 30% the aerobic bioremediation of an actual site, aged PCB-contaminated soil (with 350 mg/kg of total PCBs) when applied at 10 g/l under slurry-phase conditions. The agents did not exhibit the toxicity and the recalcitrance displayed by the chemical surfactants Triton X-100 tested at the same concentration in identical parallel laboratory-scale SBs. Then, the same group [70–72], investigated the opportunity to use less costly industrial CD products, and in particular a mixture of RAndomly MEthylated-β-cyclodextrins (RAMEB), to intensify the aerobic bioremediation of 5 other different PCB-contaminated soils under several treatment conditions including laboratory-scale SBs. A faster and more complete removal of PCBs was generally observed in the amended bioreactors for the ability of RAMEB to improve both PCB occurrence in the soil water-phase and the growth and the occurrence of soil specialized bacteria in the reactors. Larger PCBs biodegradation and dechlorination, along with larger toxicity depletion, were generally observed in SBs than in the solid-phase or saturated soil loop reactors, especially in the presence of RAMEB. This may be ascribed to the higher degree of homogeneity and higher mass-transfer rates typical of slurry-phase conditions [20, 21] which, in turn, probably enhance the intimate contact among the specialized microorganisms, the mobilizing materials and the soil-sorbed PAHs. Then, the beneficial effects of RAMEB have been also demonstrated in the aerobic bioremediation of PAH- and transformer oil-contaminated soils under laboratory slurry and solid-phase conditions as well as in the field, through pilot scale experiments conducted both under ex-situ (biopile) and in situ conditions [73]. Recently, the potential enhancing effects of other two commercial biogenic pollutant-solubilizing agents, namely a technical mixtures of Soya Lecithins and an extract of water soluble humic substances of North Dakota Lignite, on the aerobic slurry-phase bioremediation of a model soil spiked with PCBs [74, 75] and of an aged PAH-contaminated soil [11] have been demonstrated. In the latter case, a soil historically contaminated by about 13 g/kg of a large variety of PAHs was amended with soya lecithin or humic substances at 1.5% w/w and treated in aerobic solid-phase and SBs for 150 days. The overall removal of PAHs in the presence of the agents was faster and more extensive and accompanied by a larger soil detoxification, especially under slurry-phase conditions. The agents could be metabolised by soil aerobic microorganisms and enhanced the occurrence of both soil PAHs and indigenous aerobic PAHs-degrading bacteria in the reactor water-phase. Thus, the agents were biodegradable and efficiently enhance PAH biodegradation by improving the availability of both PAHs and specialized microorganisms in the soil reactors.
All biogenic pollutant-mobilizing agents mentioned above were found to be promising bioremediation enhancing additives, as capable of combining marked enhancing effects on the process with a complete biodegradability, non-toxicity and therefore a complete environmental compatibility. In addition, they are biogenic compounds and this makes their incorporation into soil more socially acceptable than that of the chemical surfactants currently proposed to intensify the bioremediation of aged PCB- and hydrocarbon-contaminated soils.
5.3 Solvents
Solvents can also be used for increasing the availability and bioavailability of low solubility-, hydrophobic pollutants in soil remediation. In particular, immiscible (in water) and non degradable solvents with affinity for hydrophobic contaminants can help in attracting the molecules of contaminants adsorbed onto soil, transfer the contaminant into the solvent phase, and afterwards to facilitate the exchange of contaminant between the solvent to the aqueous phase [6, 76] where microorganisms can finally degrade the pollutant. In SB practice, there is little or no experience on using solvents for this purpose. If it were done, the SB would be a tri-phasic bioreactor (3P-SB) with one particular solid phase (soil and microorganisms) and two liquid phases (droplets of solvent dispersed in the water phase).
Available information mainly comes from the application of two-phase 2P (liquid, solvent-water) bioreactors (Table 5). Knowledge accumulated from the 2P (liquid) bioreactor practice indicates that best solvents used for enhancing biodegradation of PAH are paraffin oil, silicone oil, n-hexadecane, corn oil, cis-jasmone, r-limonene, 2-undecanone, l-decene and n-dodecane [6, 64, 77]. The 2P bioreactor concept has been shown to be very effective for biodegradation of high concentrations of toxic organic compounds by bacteria, Table 5.
For successful application of either 3P or 2P-SB technology, appropriate selection of the solvent is of paramount importance: solvent should be immiscible in water, non toxic to microorganisms, non biodegradable, stable and non flammable, non volatile, and with high affinity for hydrophobic pollutants [78]. According to Villemur et al. [38] and Collins & Daugulis [79] 2P bioreactors might provide an efficient way to bioremediate contaminated soils. For example, in a large scale process, a 2P-SB (soil-solvent) could be used to extract pollutants from a contaminated soil by transferring to the water-immiscible, non degradable liquid phase. The solvent would then be recovered and the treated soil returned to the site. This could be repeated a number of times with the same solvent. Once the water-immiscible liquid has reached a certain concentration of contaminant, the extraction vessel could then be used as a 2P-bioreactor (liquid, solvent and water) to degrade the extracted contaminants.
6. Bioaugmentation and advances on characterization and monitoring of microbial communities of slurry bioreactors
Very often SB operation relies on the use of native microflora already existing in the polluted soil. However, whenever native microflora is scarce or weak or with no apparent capability of degrading the target compounds, it is advisable to inoculate SB with enriched/acclimated consortia or strains, more commonly consortia. This is called bioaugmentation. Thus, inoculation of 'specialized' biomass may allow for an increased biodegradation of target pollutants as well as a more effective detoxification of the solid matrix [47, 80, 81]. Another common result of bioaugmentation is the dramatic reduction of remediation times [5].
Barbeu et al. [82] have recommended a protocol for producing aerobic acclimated consortia based on activated sludge process. An outline of their procedure follows: start a complete-mix activated sludge reactor with 10% (w/v) of soil and a mineral medium. The concentration of the target pollutant(s) in the feed of bioreactor is cautiously increased step-wise until the desired concentration in the feed is reached. After 30 days of operation, provided that reactor monitoring indicates the uptake of the contaminant, an acclimated consortium is developed with the capability of using the target pollutant(s) as energy and carbon sources. Acclimated inocula can also been obtained from polluted sites such as sediments, soils and wastewaters [6, 9, 64]
To a lower extent and mainly in laboratory and pilot scale trials, specific strains have been used for bioaugmentation. A three-membered co-culture of strains of Pseudomonas sp and Alcaligenes sp. have been applied to aerobic degradation of PCBs [47]; Sphingomonas aromaticivorans to degradation of PAHs [6]; Flavobacterium sp. for degradation of naphtalene [9]Burkholderia cepacia JS872, B. cepacia and Hydrogenophaga palleronii for degradation of 2,4-DNT and 2,6-DNT [5]. However, several failures have been recorded in this field; they have been mostly ascribed to the inability of inoculated specialized pure or mixed cultures to compete with autochthonous microflora and to face the toxicity and the scarcity of nutrients occurring in the contaminated biotope [83]. Thus, the opportunity to bioaugment contaminated soils with complex microbial systems consisting of a large variety of robust microorganisms and essential nutrients has been recently explored [33, 84]. In particular, Di Toro et al. [85] studied the effects of Enzyveba, i.e. a partially characterized consortium of microorganisms developed from the stabilization of high quality organic wastes, on the aerobic bioremediation of an actual-site aged PCB-contaminated soil (overall PCBs: 920 mg/kg) under laboratory-scale slurry and solid-phase conditions. Markedly enhanced PCB-biodegradation rates and extents (from 50 to 100%) and soil detoxification as well as higher availability and persistence of aerobic PCB- and chlorobenzoic acid-degrading cultivable bacteria were observed in the Enzyveba-amended SBs. These findings suggested that Enzyveba enhanced the biotreatability of the selected soil by providing exogenous bacteria and fungi able to remove inhibitory or toxic intermediates of PCB biodegradation and/or exogenous nutrients able to sustain microorganisms in charge for PCB mineralization.
Also, dehalorespiring strains that use organo-chlorinated compounds as electron acceptors have used in bioaugmentation such as Desulfitobacterium frappieri PCP-1 and Desulfitobacterium dehalogenans introduced into non-sterile soil or soil slurry microcosms [86, 87].
Monitoring of microbial communities and specific strains in soil SBs is becoming an important tool for improving our understanding of microbial population dynamics [88], the fate of inoculated cultures as well as biodegradation mechanisms, and the influence of process operating conditions and other variables [87].
Monitoring of microbial community is traditionally accomplished by microbial counting by total or selective plating, most probable number counting, or bacterial staining followed by microscopic analysis, or by measuring microbial activity through respirometric or radiorespirometric analyses [89]. Due to experimental limitations, such as the lack of suitable electron donors or acceptors or of nutritional factors in the growth media or the unsuitable growth conditions as regards temperature, pressure or redox conditions, most of these methods are inadequate to give a reliable picture of the microbial community. However the most important factor affecting the reliability of methods based on cultivation of microorganisms is the poor culturability of most of microorganisms in complex environments such as those created in the laboratories [90]. When the active microbial population is poorly cultivable the effectiveness of a remediation process cannot be efficiently predicted or followed during a treatment by using traditional microbiological methods. Modern molecular biology tools offer in these cases several advantages respect to traditional microbiological methods, since they can couple qualitative and quantitative information on the microbial community including the uncultivable fraction. The polymerase chain reaction (PCR) and competitive PCR (cPCR) have been used with success to monitor Desulfitobacterium frappieri PCP-1 and Desulfitobacterium dehalogenans introduced into non-sterile soil or soil slurry microcosms [86, 87]. A previous report showed that strain PCP-1 can dechlorinate PCP in anaerobic soil slurry microcosms and can be monitored by PCR when introduced in this system [91]. The fatty acid methyl ester (FAME) analysis approach was successfully employed by Cassidy & Hudak [92] to selectively monitor the main bacterial and yeast strains responsible for biosurfactants production in a 8 L slurry-sequencing batch reactor developed to treat a soil contaminated with 21.8 g/kg diesel fuel. The results of the study demonstrated that SB operation can be manipulated on the basis of microbial monitoring information to control and improve the overall reactor performance [92]. No other reports on microbial molecular/biochemical monitoring of SBs were found in the literature. However, such approaches might allow predicting, following and improving the effectiveness of SB bioremediation processes, and therefore they should be included in the integrated strategies for SB monitoring and assessment.
7. Developments on ecotoxicity assays aimed at evaluating bioremediation efficiency of the process
Several types of ecotoxicity bioassays are known, some of them have already been standardised, some others are under development [93, 94]. They are carried out in polluted and treated soil to further assess treatment performance and end point. Information of these tests shed light on "true" soil detoxification achieved by treatment, in opposition of "apparent" decontamination assessed by mere chemical or instrumental analysis. In effect, pollutant removal sometimes may be accompanied by transformation of the mother contaminant into toxic intermediates that could persist in soil. So, contaminant removal not always is equivalent to decontamination or detoxification [95]. Ecotoxicity tests also account for the interactions among pollutants, which might interact through a synergic or antagonistic manner. Again, this type of interaction cannot be observed by mere instrumental analysis [96]. Thus, ecotoxicity assays appear as a significant complementary tool to assess the extent and success of bioremediation [97].
Some ecotoxicity tests are carried out using the aqueous extracts of soils: they are useful when pollutants are water soluble. The OECD [98–102] has proposed to apply a variety of tests organisms belonging to different levels of the trophic chain: microorganisms (Pseudomonas putida, Photobacterium phosphoreum), primary consumers (micro crustaceans Daphnias); secondary consumers (fish); primary producers (algae).
Yet, some other tests are performed using whole soil. These methods are also quoted as direct contact tests, as they rely on the growth or germination of well defined, artificially cultivated test-organisms directly into the contaminated soils. Test organisms include plants (Brassica rapa, Avena sativa, Lepidium sativum, etc), seeds for assessing germination, and mortalitiy of earth worms (Eisenia fetida, Eisenia andrei) [103]. These tests are particularly indicated for those soils contaminated by hydrophobic pollutants such as PAHs and PCBs, which typically are sorbed onto the soil. Other ecotoxicity assays rely on the evaluation of biological abundance or diversity of organisms autochthonous of the contaminated soils (nematodes, microorganisms) [97, 100, 104] or in the measure of some specific activities of the soil, like respiration, enzyme activities, etc. [105].
A combination of the Lepidium sativum roots and shoots elongation inhibition test and of Folsomia candida mortality test has been successfully applied by Fava and co-workers in the assessment of the efficacy of different slurry-phase bioremediation strategies developed for actual-site soils contaminated by PCBs [14, 47, 71, 72, 74, 75, 85] and PAHs [11]. The same tests along with other contact tests based on the use of selected bacteria have been applied in the monitoring of the toxicity of hydrocarbons-contaminated soils subjected to bioremediation under slurry but also solid-phase pilot-scale conditions [73].
Conclusion
SB is an ad situ and ex situ technology that can be used for bioremediation of problematic sites (when the less expensive natural attenuation or stimulated in situ bioremediation are not feasible), such as those characterized by soils with high contents of clay and organic matter, contaminated with pollutants that are recalcitrant, toxic, and display hysteretic behavior, or when bioremediation should be accomplished in relatively short times under strong pressure and monitoring of environmental agencies and regulators. SB technology allows for the convenient manipulation and control of several environmental parameters that could lead to enhanced and faster treatment of polluted soils: nutrient N, P and organic carbon source (biostimulation), inocula (bioaugmentation), increased availability of pollutants by use of surfactants or solvents, or inducing biosurfactant production inside the SB, etc. An interesting emerging area is the use of SB with simultaneous electron acceptors, which has demonstrated its usefulness for the bioremediation of soils polluted with hydrocarbons. Characterization studies of microbial communities of SB are still in the early stages, in spite of their significance for improving reactor operation and design optimization; so far SB are still modeled as "black boxes".
Inter alia, we have identified the following avenues of research for SB in the future: (i) application of SB with sequential and simultaneous electron acceptors to soils polluted with contaminants other than hydrocarbons (i.e., pesticides, explosives, etc.), (ii) evaluation of the technical feasibility of triphasic SB that use innocuous solvents to help desorbing pollutants strongly attached to soils, and in turn, to enhance their biodegradation, (iii) gaining deeper insight of microbial communities present in SB with the intensified application of molecular biology tools such as PCR-DGGE, PCR-TGGE, ARDRA, etc., (iv) development of more representative ecotoxicological assays, more complex however more informative than the mere uni-species bioassays or battery of uni-species tests (for instance, microcosm and mesocosms bioassays) to better assess the effectiveness of a given bioremediation process.
Abbreviations
- A:
-
Aerobic
- AEF:
-
Availability enhancement factor
- CMC:
-
Critical micellar capacity
- CDs:
-
Cyclodextrins
- 2:
-
4-D: 2,4-dichlorophenoxyacetic acid
- 2:
-
4-DNT: 2,4-dinitrotoluene
- 2:
-
6-DNT: 2,6-dinitrotoluene
- DEP:
-
di-ethyl phthalate
- EPTC:
-
S-ethyl dipropylthiocarbamate
- ETP:
-
Effluent treatment plant
- HCH:
-
Hexachlorocyclohexane
- CH:
-
Coefficient of hysteresis
- LO:
-
Lubricating oil
- PCR:
-
Polymerase chain reaction
- PAHs:
-
Polynuclear aromatic hydrocarbons
- PCB:
-
Polychlrorinated byphenyls
- TPH:
-
Total petroleum hydrocarbons
- 2:
-
4,6-TNB: 2,4,6-trinitrobenzene
- 2:
-
4,6-TNB 2,4,6-trinitrotoluene
- SB:
-
Slurry bioreactor
- TLP:
-
Three-phase bioreactor
- TPH:
-
Total petroleum hydrocarbons
References
Atlas RM: Microbial degradation of petroleum hydrocarbons: an environmental perspective. Microbiol Review. 1981, 45: 180-209.
Vidali M: Bioremediation. An overview. Pure Appl Chem. 2001, 73 (7): 1163-1172. 10.1351/pac200173071163.
Cho YG, Rhee SK, Lee ST: Effect of soil moisture on bioremediation of chlorophenol-contaminated soil. Biotechnol Letters. 2000, 22 (11): 915-919. 10.1023/A:1005612232079.
Korda A, Santas P, Tenente A, Santas R: Petroleum hydrocarbon bioremediation: sampling and analytical techniques, in situ treatments and commercial microorganisms currently used. Appl Microbiol Biotech. 1997, 48 (6): 677-686. 10.1007/s002530051115.
Zhang C, Hughes JB, Nishino SF, Spain JC: Slurry-phase biological treatment of 2,4-dinitrotoluene and 2,6-dinitrotoluene: role of bioaugmentation and effects of high dinitrotoluene concentrations. Environ Sci Technol. 2000, 34 (13): 2810-2816. 10.1021/es000878q.
Janikowski T, Velicogna D, Punt M, Daugulis A: Use of a two-phase partitioning bioreactor for degrading polycyclic aromatic hydrocarbons by a Sphingomonas sp. Appl Microbiol Biotechnol. 2002, 59 (2–3): 368-376.
Oberbremer A, Müller-Hurtig R, Wagner F: Effect of the addition of microbial surfactants on hydrocarbon degradation in a soil population in a stirred reactor. Appl Microbiol Biotechnol. 1990, 32 (4): 485-489. 10.1007/BF00903788.
Pinelli D, Fava F, Nocentini M, Pasquali G: Bioremediation of a polycyclic aromatic hydrocarbon-contaminated soil by using different aerobic batch bioreactor system. J Soil Contam. 1997, 243-256.
Wang SY, Vipulanandar C: Biodegradation of naphthalene-contaminated soils in slurry bioreactors. J Environ Eng. 2001, 127 (8): 748-754. 10.1061/(ASCE)0733-9372(2001)127:8(748).
Nano G, Borroni A, Rota R: Combined slurry and solid-phase bioremediation of diesel contaminated soil. J Hazard Mater. 2003, 100 (1–3): 79-94. 10.1016/S0304-3894(03)00065-7.
Fava F, Berselli S, Conte P, Piccolo A, Marchetti L: Effects of humic substances and soya lecithin on the aerobic bioremediation of a soil historically contaminated by polycyclic aromatic hydrocarbons (PAHs). Biotechnol Bioeng. 2004, 88 (2): 214-223. 10.1002/bit.20225.
Fuller ME, Manning JF: Microbiological changes during bioremediation of explosives-contaminated soils in laboratory and pilot-scale bioslurry reactors. Bioresour Technol. 2004, 91 (2): 123-133. 10.1016/S0960-8524(03)00180-9.
Robles-González I, Ríos-Leal E, Sastre-Conde I, Ferrera-Cerrato R, Caffarel-Méndez S, Poggi-Varaldo HM: Effect of supplementary organic carbon source and electron acceptors on the removal of 2,4-Dichlorophenoxyacetic acid in slurry bioreactors. Proceedings 2nd International Conference on Remediation of Contaminated Sediments, Venice, September 30 2003; Venice, Italy. Edited by: Pellei M, Porta A, Hinchee E. 2003, Battelle Press, Columbus, OH, Paper G-08, ISBN. 1-57477-143-4.
Fava F, Di Gioia D, Marchetti L: Role of the reactor configuration in the biological detoxification of a dump site-polychlorobiphenyl-contaminated soil in lab slurry phase conditions. Appl Microbiol Biotechnol. 2000, 53 (2): 243-248. 10.1007/s002530050015.
Castaldi FJ, Ford DL: Slurry bioremediation of petrochemical waste sludges. Water Sci Technol. 1992, 25 (3): 207-212.
Woo SH, Park JM: Evaluation of drum bioreactor performance used for decontamination of soil polluted with polycyclic aromatic hydrocarbons. J Chem Technol Biotechnol. 1999, 74 (10): 937-944. 10.1002/(SICI)1097-4660(199910)74:10<937::AID-JCTB128>3.0.CO;2-Q.
Mueller JG, Lantz SE, Blattman BO, Chapman PJ: Bench-scale evaluation of alternative biological treatment processes for the remediation of pentachlorophenol and creosote contaminated materials: slurry-phase bioremediation. Environ Sci Technol. 1991, 25: 1045-1055. 10.1021/es00018a005.
Eweis JB, Ergas SJ, Chang DPY, Schroeder ED: Bioremediation Principles. 1998, McGraw-Hill. USA, 207-236.
Crawford RL, Crawford DL: Bioremediation: Principles and Applications. 1996, Cambridge University Press. United Kongdom
Cookson JT: Bioremediation Engineering: Design and Application. 1995, McGraw-Hill, New York, USA
Christodoulatos C, Koutsospyros A: Bioslurry reactors. Biological treatment of hazardous wastes. Edited by: Lewandowsky GA, DeFilippi LJ. 1998, New York: John Wiley & Sons, Inc, 69-103.
Mohan VS, Shailaja S, Krishna MR, Reddy KB, Sarma PN: Bioslurry phase degradation of di-ethyl phthalate (DEP) contaminated soil in periodic discontinuous mode operation: Influence of bioaugmentation and substrate partition. Process Biochem. 2006, 41 (3): 644-652. 10.1016/j.procbio.2005.08.018.
Evans BS, Dudley CA, Klasson KT: Sequential anaerobic-aerobic biodegradation of PCBs in soil slurry microcosms. Appl Biochem Biotechnol. 1996, 57–58: 885-894.
Tabak HH, Govind R: Bioavailability and biodegradation kinetics protocol for organic pollutant compounds to achieve environmentally acceptable end-points during bioremediation. Ann NY Acad Sci. 1997, 829 (1): 36-61. 10.1111/j.1749-6632.1997.tb48564.x.
Boopathy R, Manning J, Kulpa CF: Optimization of environmental factors for the biological treatment of trinitrotoluene-contaminated soil. Arch Environ Contam Toxicol. 1997, 32 (1): 94-98. 10.1007/s002449900159.
Wenk M, Baumgartner T, Dobovsek J, Fuchs T, Kucsera J, Zopfi J, Stucki G: Rapid atrazine mineralisation in soil slurry and moist soil by inoculation of an atrazine-degrading Pseudomonas sp. strain. Appl Microbiol Biotechnol. 1998, 49 (5): 624-630. 10.1007/s002530051224.
Bachmann A, De Bruin W, Jumelet JC, Rijnaarts HH, Zehnder AJ: Aerobic biomineralization of alpha-hexachlorocyclohexane in contaminated soil. Appl Environ Microbiol. 1988, 54 (2): 548-554.
Bachmann A, Walet P, Wijnen P, De Bruin W, Huntjens JL, Roelofsen W, Zehnder AJ: Biodegradation of alpha and beta-hexachlorocyclohexane in a soil slurry under different redox conditions. Appl Environ Microbiol. 1988, 54 (1): 143-149.
Boopathy R: Use of anaerobic soil slurry reactors for the removal of petroleum hydrocarbons in soil. International Biodeterioration Biodeg. 2003, 52 (3): 161-166. 10.1016/S0964-8305(03)00054-4.
Robles-González I, Ríos-Leal E, Ferrera-Cerrato R, Esparza-García F, Rinderkenecht-Seijas N, Poggi-Varaldo HM: Bioremediation of a mineral soil with high contents of clay and organic matter contaminated with herbicide 2,4-dichlorophenoxyacetic acid using slurry bioreactors: effect of electron acceptor and supplementation with an organic carbon source. Process Biochem. 41 (9): 1951-1960. 10.1016/j.procbio.2006.04.004.
Robles-González IV, Rios-Leal E, Galíndez-Mayer J, Caffarel-Méndez S, Barrera-Córtes J, Esparza-García F, Poggi-Varaldo HM: Comportamiento adsortivo-desortivo del lindano en un suelo agrícola. Interciencia. 2006, 31 (4): 305-308.
Yun YS, Park JI, Suh MS, Park JM: Treatment of food wastes using slurry-phase decomposition. Bioresour Tech. 2000, 73 (1): 21-27. 10.1016/S0960-8524(99)00131-5.
Castaldi FJ: Tank-based bioremediation of petroleum waste sludges. Environ Prog. 2003, 22 (1): 25-36. 10.1002/ep.670220114.
Montante G, Pinelli D, Magelli F: Scale-up criteria for the solids distribution in slurry reactors strirred with multiple impellers. Chem Eng Sci. 2003, 58 (23–24): 5363-5372. 10.1016/j.ces.2003.09.021.
Alexander M: Biodegradation and Bioremediation. 1999, Academic Press. San Diego, California. USA, 356-361.
Woo SH, Jeon CO, Park JM: Phenantrene biodegradation in soil slurry systems: Influence of salicylate and Triton X-100. Korean J Chem Eng. 2004, 21 (2): 412-418. 10.1007/BF02705429.
Alexander M: Biodegradation of chemicals of environmental concern. Science. 1981, 211 (4478): 132-138. 10.1126/science.7444456.
Jee V, Beckles DM, Ward CH, Hughes JB: Aerobic slurry reactor treatment of phenanthrene contaminated sediment. Water Res. 1998, 32 (4): 1231-1239. 10.1016/S0043-1354(97)00333-3.
Dean-Ross D: Biodegration of selected PAH from sediment in bioslurry reactors. Bull Environ Contam Toxicol. 2005, 74: 32-39. 10.1007/s00128-004-0544-4.
Villemur R, Déziel E, Benachenhou A, Marcoux J, Gauthier E, Lépine F, Beaudet R, Comeau Y: Two-liquid-phase slurry bioreactors to enhance the degradation of high-molecular-weight polycyclic aromatic hydrocarbons in soil. Biotechnol Prog. 2000, 16 (6): 966-972. 10.1021/bp000118j.
Rutherford PM, Banerjee DK, Luther SM, Gray MR, Dudas MJ, McGill WB, Pickard MA, Salloum MJ: Slurry-phase bioremediation of creosote and petroleum-contaminated soils. Environ Technol. 1998, 19 (7): 683-696.
De Jonge H, Verstrate JM: Increased mineral oil bioavailability in slurries by monovalent cation-induced dispersion. 3rd Int In Situ and On Site Bioremediation Simposium. Edited by: Hinchee RH, Vogel CM, Brockman FJ. 1993, Battelle Press. Columbus, OH, ISBN 1-57477-099-8
Kuyukina MS, Ivshina IB, Ritchova MI, Philp JC, Cunningham CJ, Christofi N: Bioremediation of crude oil contaminated soil using slurry-phase biological treatment and landfarming techniques. Soil Sediment Contam. 2003, 12 (1): 85-99. 10.1080/713610962.
Lewis R: Slurry biodegradation removes wide range of organics in soils. Tech Trends EPA/542/N-92/001. 1992, 8: 2-
Fava F, Di Gioia D, Marchetti L: Cyclodextrin effects on the ex-situ bioremediation of a chronically polychlorobiphenyl-contaminated soil. Biotechnol Bioeng. 1998, 58 (4): 345-355. 10.1002/(SICI)1097-0290(19980520)58:4<345::AID-BIT1>3.0.CO;2-J.
Fava F, Di Gioia D: Effects of Triton X-100 and Quillaya Saponin on the ex-situ bioremediation of a chronically polychlorobiphenyl-contaminated soil. Appl Microbiol Biotechnol. 1998, 50 (5): 623-630. 10.1007/s002530051345.
Fava F, Bertin L: Use of exogenous specialised bacteria in the biological detoxification of a dump site-polychorobiphenyl-contaminated soil in slurry phase conditions. Biotechnol Bioeng. 1999, 64 (2): 240-249. 10.1002/(SICI)1097-0290(19990720)64:2<240::AID-BIT13>3.0.CO;2-F.
Rattan K, Shanker R, Khanna P, Atkins WM: Stress survival of a genetically engineered pseudomonas in soil slurries: cytochrome P-450cam-catalyzed dehalogenation of chlorinated hydrocarbons. Biotechnol Prog. 1999, 15 (5): 958-962. 10.1021/bp990097x.
Hudak AJ, Cassidy DP: Stimulating in-soil rhamnolipid production in a bioslurry reactor by limiting nitrogen. Biotechnol Bioeng. 2004, 88 (7): 861-868. 10.1002/bit.20295.
Nishino SF, Spain JC, Lenke H, Knackmuss HJ: Mineralization of 2,4- and 2,6-dinitrotoluene in soil slurries. Environ Sci Technol. 1999, 33: 1060-1064. 10.1021/es9808301.
Edwards EA, Wills LE, Reinhard M, D Grbiæ-Galiæ: Anaerobic degradation of toluene and xilene by aquifer microorganisms under sulfate reducing conditions. Appl Environ Microbiol. 1992, 58 (3): 794-800.
Evans PJ, Mang DT, King KS, Young LY: Anaerobic degradation of toluene by a denitrifying bacterium. Appl Environ Microbiol. 1991, 57 (4): 1139-1145.
Mihelcic JR, Luthy RG: Degradation of polycyclic aromatic hydrocarbon compounds under various redox conditions in soil-water system. Appl Environ Microbiol. 1988, 54 (5): 1182-1187.
Rueter P, Rabus R, Wilkes H, Aeckersberg F, Rainey FA, Jannasch HW, Widdel F: Anaerobic oxidation of hydrocarbons in crude oil by new types of sulfate-reducing bacteria. Nature. 1994, 372 (6505): 455-458. 10.1038/372455a0.
Environmental Protection Agency: Simplot ex-situ anaerobic bioremediation technology:TNT. 540/R-95/529a. 1995, Office of research and development. Cincinnati, OH, USA
Poggi-Varaldo HM, Rinderknecht-Seijas N, Caffarel-Mendez S: Irreversibilidad en el comportamiento adsortivo-desortivo de contaminantes en suelos y sedimentos: evaluación cuantitativa por medio de un coeficiente de histéresis diferencial. Interciencia. 2002, 27 (4): 180-185.
Poggi-Varaldo HM, Rinderknecht-Seijas N: A differential availability enhancement factor for the. evaluation of pollutant availability in soil treatments. Acta Biotechnol. 2003, 23 (2–3): 271-280. 10.1002/abio.200390034.
Rouse JD, Sabatini DA, Suflita JM, Harwell JH: Influence of surfactant on microbial degradation of organic compounds. Crit Rev Environ Sci Technol. 1994, 24 (4): 325-370.
West CC, Harwell JH: Surfactants and subsurface remediation. Environ Sci Technol. 1992, 26: 2324-2330. 10.1021/es00036a002.
Amezcua-Vega C, Rodríguez-Vázquez R, Poggi-Varaldo HM, Ríos-Leal E: Effect of a rhamnolipid biosurfactant on the phenanthrene desorption from a clay-loam soil. Bioremediation of Energetics, Phenolics and Polycyclic Aromatic Hydrocarbons. 2001, Battelle Press, Columbus, OH, USA, ISBN 1-57477-113-2
Amezcua-Vega C, Poggi-Varaldo HM, Esparza-García F, Ríos-Leal E, Rodríguez-Vázquez R: Effect of culture conditions on fatty acids composition of a biosurfactant produced by Candida ingens and changes of surface tension of culture media. Bioresource Technol. 2007, 98 (1): 237-240. 10.1016/j.biortech.2005.11.025.
Christofi N, Ivshina IB: Microbial surfactants and their use in field studies of soil remediation. J Appl Microbiol. 2002, 93 (6): 915-929. 10.1046/j.1365-2672.2002.01774.x.
Kosaric N: Biosurfactants and their application for soil bioremediation. Food Technol Biotechnol. 2001, 39 (4): 295-304.
Marcoux J, Déziel E, Villemur R, Lépine F, Bisaillon JG, Beaudet R: Optimization of high-molecular-weight polycyclic aromatic hydrocarbons degradation in a two-liquid-phase bioreactor. J Appl Microbiol. 2000, 88 (4): 655-662. 10.1046/j.1365-2672.2000.01011.x.
Rosenberg E, Ron EZ: High- and low-molecular-mass microbial surfactants. Appl Microbiol Biotechnol. 1999, 52 (2): 154-162. 10.1007/s002530051502.
Tiehm A: Degradation of polycyclic aromatic hydrophobic compounds in the presence of synthetic surfactants. Appl Environ Microbiol. 1994, 60 (1): 258-263.
Volkering F, Breure AM, Rulkens WH: Microbiological aspects of surfactant use for biological soil remediation. Biodegradation. 1997, 8 (6): 401-417. 10.1023/A:1008291130109.
Quintero JC, Moreira MT, Feijoo G, Lema JM: Anaerobic degradation of hexachlorocyclohexane isomers in liquid and soil slurry systems. Chemosphere. 2005, 61 (4): 528-536. 10.1016/j.chemosphere.2005.02.010.
Deschênes L, Lafrance P, Villeneuve JP, Samson R: Adding sodium dodecyl sulfate and Pseudomonas aeruginosa UG2 biosurfactants inhibits polycyclic aromatic hydrocarbons biodegradation in a weathered creosate-contaminated soil. Appl Microbiol Biotechnol. 1996, 46 (5–6): 638-646.
Fava F, Ciccotosto FV: Effects of Randomly Methylated-β-Cyclodextrins (RAMEB) on the bioavailability and aerobic biodegradation of polychlorinated biphenyls in three pristine soils spiked with a transformer oil. Appl Microbiol Biotechnol. 2002, 58: 393-399. 10.1007/s00253-001-0882-7.
Fava F, Di Gioia D, Marchetti L, Fenyvesi E, Szejtli J: Randomly methylated α-cyclodextrins (RAMEB) enhance the aerobic biodegradation of polychlorinated biphenyls in aged-contaminated soils. J Inclusion Phenom Mol Recognit Chem. 2002, 44: 417-421. 10.1023/A:1023019903194.
Fava F, Bertin L, Fedi S, Zannoni D: Methyl-β-cyclodextrin enhanced solubilization and aerobic biodegradation of polychlorinated biphenyls in two aged-contaminated soils. Biotechnol Bioeng. 2003, 81: 384-390. 10.1002/bit.10579.
Molnár M, Leitgib L, Gruiz K, Fenyvesi É, Szaniszló N, Szejtli J, Fava F: Enhanced biodegradation of transformer oil in soils with cyclodextrin – from the laboratory to the field. Biodegradation. 2005, 16 (2): 159-168. 10.1007/s10532-004-4873-0.
Fava F, Di Gioia D: Soya lecithin effects on the aerobic biodegradation of polychlorinated biphenyls in an artificially-contaminated soil. Biotechnol Bioeng. 2001, 72 (2): 177-184. 10.1002/1097-0290(20000120)72:2<177::AID-BIT6>3.0.CO;2-K.
Fava F, Piccolo A: Effects of humic substances on the bioavailability and aerobic biodegradation of polychlorinated biphenyls in a model soil. Biotechnol Bioeng. 2002, 77 (2): 204-211. 10.1002/bit.10140.
Smith MJ, Lethbridge G, Burns RG: Bioavailability and biodegradation of polycyclic aromatic hydrocarbons in soils. FEMS Microbiol Lett. 1997, 152 (1): 141-147. 10.1111/j.1574-6968.1997.tb10420.x.
Jimenez I, Bartha R: Solvent-augmented mineralization of pyrene by a Mycobacterium sp. Appl Environ Microbiol. 1996, 62 (7): 2311-2316.
Daugulis AJ: Two-phase partitioning bioreactors: a new technology platform for destroying xenobiotics. Trends in Biotechnol. 2001, 19 (11): 457-462. 10.1016/S0167-7799(01)01789-9.
Collins D, Daugulis AJ: BTX degradation part II: effect of substrate interactions and feeding strategies in toluene-benzene and toluene-p-xilene fermentations in a partitioning bioreactor. Appl Microbiol Biotechnol. 1999, 52 (3): 360-365. 10.1007/s002530051532.
Baker BH, Herson DS: Bioremediation. 1994, McGraw-Hill, 1-25. 193–195, 238–247.
Silva E, Fialho AM, Sá-Correia I, Burns RG, Shaw LJ: Combined bioaugmentation and biostimulation to cleanup soil contaminated with high concentrations of atrazine. Environ Sci Technol. 2004, 38 (2): 632-637. 10.1021/es0300822.
Barbeu C, Deschênes L, Karamanev D, Comeau Y, Samson R: Bioremediation of pentachlorophenol-contaminated soil by bioaugmentation using activated soil. Appl Microbiol Biotechnol. 1997, 48 (6): 745-752. 10.1007/s002530051127.
Goldstein RM, Mallory LM, Alexander M: Reasons for possible failure of inoculation to enhance biodegradation. Appl Environ Microbiol. 1985, 50 (4): 977-983.
Dejonghe W, Boon N, Seghers D, Top EM, Verstraete W: Bioaugmentation of soils by increasing microbial richness: missing links. Environ Microbiol. 2001, 3 (10): 649-657. 10.1046/j.1462-2920.2001.00236.x.
Di Toro S, Zanaroli G, Fava F: Intensification of the aerobic bioremediation of an actual site soil historically contaminated by polychlorinated biphenyls (PCBs) through bioaugmentation with a non acclimated, complex source of microorganisms. Microb Cell Fact. 2006, 5: 11-21. 10.1186/1475-2859-5-11.
El Fantroussi S, Mahillon J, Naveau H, Agathos SN: Introduction of anaerobic dechlorination bacteria into soil slurry microcosms and nested-PCR monitoring. Appl Environ Microbiol. 1997, 63 (2): 806-811.
Lanthier M, Villemur R, Lépine F, Bisaillon JG, Beaudet R: Monitoring of Desulfitobacterium frappieri PCP-1 in pentachlorophenol-degrading anaerobic soil slurry reactors. Environ Microbiol. 2000, 2 (6): 703-708. 10.1046/j.1462-2920.2000.00144.x.
Fedi S, Tremaroli V, Scala D, Perez-Jimenez JR, Fava F, Young LY, Zannoni D: T-RFLP analysis of bacterial communities in cyclodextrins amended bioreactors developed for biodegradation of polychlorinated biphenyls (PCBs). Res Microbiol. 2005, 156 (2): 201-210.
Head IM: Bioremediation: towards a credible technology. Microbiol. 1998, 144: 599-608.
Amann RI, Ludwig W, Schleifer KH: Phylogenetic identification and in situ detection of individual microbial cells without cultivation. Microbiol Rev. 1995, 59 (1): 143-169.
Beaudet R, Lévesque MJ, Villemur R, Lanthier M, Chénier M, Lépine F, Bisaillon JG: Anaerobic biodegradation of pentachlorophenol in a contaminated soil inoculated with a methanogenic consortium or with Desulfitobacterium frappieri strain PCP-1. Appl Microbiol Biotechnol. 1998, 50 (1): 135-141. 10.1007/s002530051268.
Cassidy DP, Hudak AJ: Microorganism selection and biosurfactant production in a continuously and periodically operated bioslurry reactor. J Hazard Mat. 2001, 84 (2–3): 253-264. 10.1016/S0304-3894(01)00242-4.
Calow P: Handbook of Ecotoxicology. 1993, Blackwell Science Ltd
Landis WG, Yu MH: Introduction to Environmental Toxicology: impact of chemicals upon ecological systems. 1999, CRC Press LLC, New York, Boca Raton, Florida
Belkin S, Stieber M, Tiehm A, Frimmel FH, Abeliovich A, Werner P, Ulitzur S: Toxicity and genotoxicity enhancement during polycyclic aromatic hydrocarbons biodegradation. Environ Toxicol Water Qual. 1994, 9: 303-309. 10.1002/tox.2530090409.
Horvath B, Gruiz k, Sára B: Ecotoxicological testing of soil by four bacterial biotests. Toxicol Environ Chem. 1997, 58: 223-235.
Hund K, Traunspurger W: Ecotox-evaluation strategy for soil bioremediation exemplified for a PAH-contaminated site. Chemosphere. 1994, 29 (2): 371-390. 10.1016/0045-6535(94)90111-2.
OECD (Organization for Economic Cooperation and Development): Alga, growth inhibition test. 1984, Guineline No. 201 Paris, France
OECD (Organization for Economic Cooperation and Development): Daphnia sp., acute immobilisation test and reproduction test. 1984, Guideline No. 202 Paris, France
OECD (Organization for Economic Cooperation and Development): Earthworm, acute toxicity test. 1984, Guideline No. 207 Paris, France
OECD (Organization for Economic Cooperation and Development): Terrestrial plant test. 1984, Guideline No. 208 Paris, France
OECD (Organization for Economic Cooperation and Development): Fish, Acute toxicity test. 1992, Guideline No. 203 Paris, France
Riepert F, Kula C: Development of laboratory methods for testing effects of chemicals and pesticides on Collembola and earthworms. 1996, Mitteilungen aus der Biologischen Bundesanstalt für Land-und Forstwirtschaft. Berlin: BBLF
Hankard PK, Bundy JG, Spurgeon DJ, Weeks JM, Wright J, Weinberg CI, Svendsen C: Establishing principal soil quality parameters influencing earthworms in urban soils using bioassays. Environ Pollut. 2005, 133 (2): 199-211. 10.1016/j.envpol.2004.06.008.
Dobler R, Burri P, Gruiz K, Brandl H, Bachofen R: Variability in microbial populations in soil highly polluted with heavy metals on the basis of substrate utilization pattern analysis. J Soils and Sediments. 2001, 1 (3): 151-158.
Schuur JHB, Mattiasson B: Separation of coal-tar constituents from soil particles in a two-liquid-phase slurry system. Environ Technol. 2003, 24 (6): 755-765.
Piskonen R, Nyyssönen M, Rajamäki T, Itävaara M: Monitoring of accelerated naphthalene-biodegradation in a bioaugmented soil slurry. Biodegradation. 2005, 16 (2): 127-134. 10.1007/s10532-004-4893-9.
Garon D, Sage L, Wouessidjewe D, Seigle-Murandi F: Enhanced degradation of fluorine in soil slurry by Absidia cylindrospora and maltosyl-cyclodextrin. Chemosphere. 2004, 56 (2): 159-166. 10.1016/j.chemosphere.2004.02.019.
Znad H, Kasahara N, Kawase Y: Biological decomposition of herbicides (EPTC) by activated sludge in a slurry bioreactor. Process Biochem. 2006, 41 (5): 1124-1128. 10.1016/j.procbio.2005.12.006.
Fuller ME, Kruczek J, Schuster RL, Sheehan PL, Arienti PM: Bioslurry treatment for soils contaminated with very high concentrations of 2,4,6-trinitrophenylmethylnitramine (tetryl). J Hazard Mater. 2006
Nishino SF, Spain JC: Technology status review: Bioremediation of dinitrotoluene (DNT). Air Force Research Laboratory. 2001, Tyndall AFB, Florida
Kao CM, Chen SC, Liu JK, Wu MJ: Evaluation of TCDD biodegradability under different redox conditions. Chemosphere. 2001, 44 (6): 1447-1454. 10.1016/S0045-6535(00)00464-1.
Mohan SV, Sirisha K, Rao NC, Sarma PN, Reddy SJ: Degradation of chlorpyrifos contaminated soil by bioslurry reactor operated in sequencing batch mode: bioprocess monitoring. J Hazard Mater. 2004, 116 (1–2): 39-48. 10.1016/j.jhazmat.2004.05.037.
Shen CF, Guiot SR, Thiboutot S, Ampleman G, Hawari J: Fate explosives and their metabolites in bioslurry treatment processes. Biodegradation. 1998, 8 (5): 339-347. 10.1023/A:1016094932066.
Johnson K, Ghosh S: Feasibility of anaerobic biodegradation of PAHs in dredged river sediments. Water Sci Technol. 1998, 38 (7): 41-48. 10.1016/S0273-1223(98)00605-2.
Shen CF, Hawari JA, Ampleman G, Thiboutot S, Guiot SR: Origin of p-cresol in the anaerobic degradation of trinitrotoluene. Can J Microbiol. 2000, 46 (2): 119-124. 10.1139/cjm-46-2-119.
Lee T, Tokunaga T, Suyama A, Furukawa K: Efficient dechlorination of tetrachlroethylene in soil slurry by combined use of an anaerobic Desulfitobacterium sp. strain Y-51 and zero-valent iron. J Bioscience Bioeng. 2001, 92 (5): 453-458. 10.1263/jbb.92.453.
Acknowledgements
The authors wish to thank CONACYT for a graduate scholarship to IVR-G, and CINVESTAV. The insightful comments and suggestions of the Editor and the anonymous Referees of Microbial Cell Factories are gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Additional information
Authors' contributions
All authors participated equally in the conception and writing of this review. All authors read and approved the final manuscript.
Authors’ original submitted files for images
Below are the links to the authors’ original submitted files for images.
Rights and permissions
Open Access This article is published under license to BioMed Central Ltd. This is an Open Access article is distributed under the terms of the Creative Commons Attribution License ( https://creativecommons.org/licenses/by/2.0 ), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
About this article
Cite this article
Robles-González, I.V., Fava, F. & Poggi-Varaldo, H.M. A review on slurry bioreactors for bioremediation of soils and sediments. Microb Cell Fact 7, 5 (2008). https://doi.org/10.1186/1475-2859-7-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1186/1475-2859-7-5