Skip to main content
SpringerLink
Log in

Numerical Nonlinear Buckling Analysis of Tapered Slender Reinforced Concrete Columns

  • Research Paper
  • Published:
International Journal of Civil Engineering Aims and scope Submit manuscript

Abstract

Tapered columns could be used either for architectural purposes or for structural needs to accommodate the variation of moments along the height of the column. In highway bridges, tapered columns are usually used to reduce the amount of moments that are transferred from the column base to the foundation. This paper studies slender RC columns with a linear variation in the columns’ cross section in both the principal directions of the cross section. Two slenderness ratios of 70 and 40 have been investigated in this study for RC tapered columns. Computational analysis, using the finite element (FE) method, is conducted in this study after the calibration of the reference FE models with tests that were conducted by other researches in Jenkins (Improving the design of slender, concrete columns. Doctoral dissertation, Purdue University, West Lafayette, 2015). These FE models were extended to account for different degrees of column tapering. The paper found that a minor tapering of the column (where the tapering ratio is greater than 150) is just an esthetic feature and it does not contribute to the buckling load of RC columns. In case of slender columns with a slenderness ratio of 40, the increase in the tapering of the column causes a slight increase in the buckling load of roughly 15%, as compared with non-tapered columns that have the same slenderness ratio. On the other hand, the increase in the buckling load of columns that have a slenderness ratio of 70 is about 45%. Analytical solutions based on the eigenvalue problem have also been presented to estimate the buckling load of a variety of tapering ratios.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12

Similar content being viewed by others

References

  1. MacGregor JG, Breen JE (1970) Design of slender concrete columns. J Proc 67(1):6–28

    Google Scholar 

  2. MacGregor JG, Barter SL (1966) Long eccentrically loaded concrete columns bent in double curvature. In: Symposium on reinforced concrete columns—ACI special publication 13(1):139–156

  3. Jenkins RW (2015) Improving the design of slender, concrete columns. Doctoral dissertation, Purdue University, West Lafayette

  4. ACI (American Concrete Institute) (2014) Building code requirements for structural concrete and commentary. ACI 318-14, Farmington Hills

    Google Scholar 

  5. Mirza S (1990) Flexural stiffness of rectangular reinforced concrete columns. ACI Struct J 87(4):425–435

    Google Scholar 

  6. Khuntia M, Ghosh SK (2004) Flexural stiffness of reinforced concrete columns and beams: experimental verification. Struct J 101(3):364–374

    Google Scholar 

  7. Lloyd NA, Rangan BV (1995) High strength concrete columns under eccentric compression. In: Doctoral dissertation, School of Civil Engineering Curtin University of Technology, Perth, Western Australia

  8. Alavi A, Rahgozar R (2018) A simple mathematical method for optimal preliminary design of tall buildings with peak lateral deflection constraint. Int J Civil Eng 6(1):1–8. https://doi.org/10.1007/s40999-018-0349-1

    Article  Google Scholar 

  9. Hu HT, Huang CS, Wu MH, Wu YM (2003) Nonlinear analysis of axially loaded concrete-filled tube columns with confinement effect. J Struct Eng 129(10):1322–1329

    Article  Google Scholar 

  10. Takiguchi K (2003) An investigation into the behavior and strength of reinforced concrete columns strengthened with ferrocement jackets. Cement Concrete Composites 25(2):233–242

    Article  Google Scholar 

  11. Ozcan O, Binici B, Ozcebe G (2008) Improving seismic performance of deficient reinforced concrete columns using carbon fiber-reinforced polymers. Eng Struct 30(6):1632–1646

    Article  Google Scholar 

  12. Fitzwilliam J, Bisby LA (2010) Slenderness effects on circular CFRP confined reinforced concrete columns. J Composit Construct 14(3):280–288

    Article  Google Scholar 

  13. Marques L, Da Silva LS, Rebelo C (2014) Rayleigh-Ritz procedure for determination of the critical load of tapered columns. Steel Comp Struct 16(1):45–58

    Article  Google Scholar 

  14. Li QS (2008) A stability of non-uniform columns under the combined action of concentrated follower forces and variably distributed loads. J Construct Steel Res 64(3):367–376

    Article  Google Scholar 

  15. Maiorana E, Pellegrino C (2011) Linear buckling analysis of welded girder webs with variable thickness. Steel Compos Struct Int J 11(6):505–524

    Article  Google Scholar 

  16. Ermopoulos J (1997) Equivalent buckling length of non-uniform members. J Construct Steel Res 42(2):141–158

    Article  Google Scholar 

  17. Yossif WV (2008) Elastic critical load of tapered members. J Eng Dev 12(1):148–160

    Google Scholar 

  18. Coskun SB, Öztürk B (2012) Elastic stability analysis of euler columns using analytical approximate techniques. Adv Comput Stabil Anal 6(1):115–132

    Google Scholar 

  19. Iremonger MJ (1980) Finite difference buckling analysis of non-uniform columns. Comput Struct 12(5):741–748

    Article  MathSciNet  MATH  Google Scholar 

  20. Head MC, Aristizabal-Ochoa JD (1987) Analysis of prismatic and linearly tapered reinforced concrete columns. J Struct Eng 113(3):575–589

    Article  Google Scholar 

  21. Gallagher RH, Lee CH (1970) Matrix dynamic and instability analysis with non-uniform elements. Int J Numer Meth Eng 2(2):265–275

    Article  MATH  Google Scholar 

  22. ABAQUS (2011) Analysis user’s manual online documentation. Dassault Systèmes Simulia Corp, Providence

  23. Chang GA, Mander JB (1994) Seismic energy based fatigue damage analysis of bridge columns: part 1—evaluation of seismic capacity. NCEER Technical Report No. NCEER-94-0006, State University of New York, Buffalo

  24. MATLAB and Optimization Toolbox Release (2012) The MathWorks, Inc, Natick

Download references

Funding

Not applicable.

Author information

Authors and Affiliations

  1. Department of Civil Engineering, University of Jordan, Queen Rania St, Amman, 11942, Jordan

    Amer Alkloub, Rabab Allouzi & Hana Naghawi

Authors
  1. Amer Alkloub
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Rabab Allouzi
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Hana Naghawi
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Amer Alkloub.

Ethics declarations

Conflict of interest

On behalf of all authors, the corresponding author states that there is no conflict of interest.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Alkloub, A., Allouzi, R. & Naghawi, H. Numerical Nonlinear Buckling Analysis of Tapered Slender Reinforced Concrete Columns. Int J Civ Eng 17, 1227–1240 (2019). https://doi.org/10.1007/s40999-019-00395-5

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40999-019-00395-5

Keywords

Search

Navigation