Skip to main content
SpringerLink
Log in

Empirical Models for Prediction of Frost Resistance of Normal- and High-Strength Concretes

  • Research Paper
  • Published:
Iranian Journal of Science and Technology, Transactions of Civil Engineering Aims and scope Submit manuscript

Abstract

This study aimed to derive practical empirical models of frost resistance for both normal-strength (NS) and high-strength (HS) concretes (NSC and HSC) using a comprehensive test program. For this purpose, the effects of the three key parameters of water-to-cement (w/c) ratio (at levels of 0.5, 0.6, 0.7, and 0.8), air content (at levels of 3, 4.5, 6, and 7.5%), and the number of freeze–thaw cycles, FTCs, (45, 100, and 150 cycles) were investigated on the frost resistance of NSC. To study the effect of key parameters on the frost resistance of HSC, the influence of water-to-cementitious materials ratio, w/cm, (0.25, 0.3, and 0.4), silica fume (SF) content (0, 5, 10, and 15%), type of coarse aggregate (limestone and quartzite), and number of FTCs (45, 150, and 200) was investigated. The experiments were performed using 720 concrete specimens divided into 288 NS and 432 HS concrete specimens. Finally, some models for predicting the frost resistance of NS and HS concretes were proposed. Validation of the proposed models using different parameters and previous studies showed their good capability to predict frost resistance of HS and NS concretes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

Availability of data and materials

Some or all data, models, or codes that support the findings of this study are available from the corresponding author upon reasonable request, including the data used for plotting the figures, the design calculation procedure, and additional photographs of the test specimens.

References

  • American Concrete Institute (2002) ACI Committee 211: Standard practice for selecting properties of normal, heavyweight and mass concrete (ACI 211.1-91, Reapproved 2009). American Concrete Institute, Farmington Hills, MI

    Google Scholar 

  • American Concrete Institute (2011) ACI Committee 214: Guide to evaluation of strength test results in concrete (ACI 214R-11). American Concrete Institute, Farmington Hills, MI

    Google Scholar 

  • American Concrete Institute (2016) ACI Committee 201: Guide to durable concrete (ACI 201.2R-16). American Concrete Institute, Farmington Hills, MI

    Google Scholar 

  • ASTM International (2014) Standard test methods for compressive strength and elastic moduli of intact rock core specimens under varying states of stress and temperatures (ASTM D7012-14), West Conshohocken, PA, 2014, www.astm.org

  • ASTM International (2015) Standard test method for resistance of concrete to rapid freezing and thawing (ASTM C666/C666M-15), West Conshohocken, PA, www.astm.org

  • ASTM International (2015) Standard test method for slump of hydraulic-cement concrete (ASTM C143/C143M-15a), West Conshohocken, PA, www.astm.org

  • ASTM International (2016) Standard specification for portland cement (ASTM C150/C150M-16), West Conshohocken, PA, www.astm.org

  • ASTM International (2017) Standard test method for air content of freshly mixed concrete by the pressure method (ASTM C231/C231M-17a), West Conshohocken, PA, www.astm.org

  • Bahmani H, Mostofinejad D, Dadvar SA (2020a) Effects of synthetic fibers and different levels of partial cement replacement on mechanical properties of UHPFRC. J Mater Civ Eng 32(12):04020361

    Google Scholar 

  • Bahmani H, Mostofinejad D, Dadvar SA (2020b) Mechanical properties of ultra-high-performance fiber-reinforced concrete containing synthetic and mineral fibers. ACI Mater J 117(3):155–168

    Google Scholar 

  • Bakharev T, Struble LJ (1994) Microstructural features of freeze-thaw deterioration of concrete. MRS Online Proceedings Library Archive 370

  • Bogas JA, De Brito J, Ramos D (2016) Freeze–thaw resistance of concrete produced with fine recycled concrete aggregates. J Clean Prod 115:294–306

    Google Scholar 

  • Cai H, Liu X (1998) Freeze-thaw durability of concrete: ice formation process in pores. Cem Conc Res 28(9):1281–1287

    Google Scholar 

  • Cao J, Chung D (2002) Damage evolution during freeze–thaw cycling of cement mortar, studied by electrical resistivity measurement Cem. Conc Res 32(10):1657–1661

    Google Scholar 

  • Daghighi A, Nahvi A, Samadi D, Rahmani T, Shekarchi M (2014) Comparison of the concrete electrical resistivity and compressive strength by effect of freeze-thaw cycling. 6th National Conference of Concrete, Tehran, Iran (In Persian)

  • Duan A, Jin W, Qian J (2011) Effect of freeze–thaw cycles on the stress–strain curves of unconfined and confined concrete Mater. Structure 44(7):1309–1324

    Google Scholar 

  • Duan A, Tian Y, Dai JG, Jin WL (2014) A stochastic damage model for evaluating the internal deterioration of concrete due to freeze–thaw action. Mater Struct 47(6):1025–1039

    Google Scholar 

  • He Z, Tang S, Zhao G, Chen E (2016) Comparison of three and one dimensional attacks of freeze-thaw and carbonation for concrete samples Constr. Build Mater 127:596–606

    Google Scholar 

  • Hooton R (1993) Influence of silica fume replacement of cement on physical properties and resistance to sulfate attack, freezing and thawing, and alkali-silica reactivity. ACI Mater J 90(2):143–151

    Google Scholar 

  • Hover K (1993) Why is there air in concrete? Conc Constr 38(1):11–15

    Google Scholar 

  • Huang Y, Wang Y, Wang R, Zhou Y, Ding Q (2020) Fractional-order freezing-and-thawing damage model for hydraulic concrete subjected to variable temperature processes. Struct Concr. https://doi.org/10.1002/suco.201900391

    Article  Google Scholar 

  • Karakoç MB, Demirboğa R, Türkmen İ, Can İ (2011) Modeling with ANN and effect of pumice aggregate and air entrainment on the freeze–thaw durabilities of HSC. Constr Build Mater 25(11):4241–4249

    Google Scholar 

  • Li A, Xu S, Wang Y (2017) Effects of frost-damage on mechanical performance of concrete. J Wuhan Univ Technol Mater Sci Ed 32(1):129–135

    MathSciNet  Google Scholar 

  • Liu L, Ye G, Schlangen E, Chen H, Qian Z, Sun W, Van Breugel K (2011) Modeling of the internal damage of saturated cement paste due to ice crystallization pressure during freezing Cem. Concr Compos 33(5):562–571

    Google Scholar 

  • Liu H, Luo G, Wei H, Yu H (2018a) Strength, permeability, and freeze-thaw durability of pervious concrete with different aggregate sizes, porosities, and water-binder ratios. Appl Sci 8(8):1217

    Google Scholar 

  • Liu L, Qin S, Wang X (2018b) Poro-elastic–plastic model for cement-based materials subjected to freeze–thaw cycles Constr. Build Mater 184:87–99

    Google Scholar 

  • Lu X, Sun Q, Feng W, Tian J (2013) Evaluation of dynamic modulus of elasticity of concrete using impact-echo method. Constr Build Mater 47:231–239

    Google Scholar 

  • Marzouk H, Jiang D (1994) Effects of freezing and thawing on the tension properties of high-strength concrete. ACI Mater J 91(6):577–586

    Google Scholar 

  • Minitab 17 statistical software (2010) [Computer Software]. State College, PA: Minitab, Inc. (www.minitab.com)

  • Mori H, Ishikawa Y, Shibata T, Okamoto T (1999) Deterioration of concrete using artificial lightweight aggregate under freezing and thawing conditions (Special issue on structural materials). J Soc Mater Sci 48(8):889–894

    Google Scholar 

  • Mostofinejad D, Nozhati M (2005) Prediction of the modulus of elasticity of high strength concrete IRAN. J Sci Technol B 29(B3):311–321

    Google Scholar 

  • Mostofinejad D, Nikoo MR, Hosseini SA (2016) Determination of optimized mix design and curing conditions of reactive powder concrete (RPC) Constr. Build Mater 123:754–767

    Google Scholar 

  • Neville AM (1963) Properties of concrete. Pearson Education Asia, Longman

    Google Scholar 

  • Neville AM, Brooks JJ (2010) Concrete technology. Prentice Hall, Upper Saddle River

    Google Scholar 

  • Nili M, Azarioon A, Hosseinian SM (2017) Novel internal-deterioration model of concrete exposed to freeze-thaw cycles. J Mater Civ Eng 29(9):0401713

    Google Scholar 

  • Pasqualini A, Bressan M, Liberatore FM (2015) Durability and sustainability of fly ash HPC exposed to freeze-thaw cycles. Special Publication 305, 20.21-20.28

  • Patil HS, Dwivedi A, Chatterjee A (2017) Optimize properties of concrete with silica fume MAYFEB. J Mater Sci

  • Penttala V (2006) Surface and internal deterioration of concrete due to saline and non-saline freeze–thaw loads Cem. Conc Res 36(5):921–928

    Google Scholar 

  • Ramezanianpour A, Malhotra V (1995) Effect of curing on the compressive strength, resistance to chloride-ion penetration and porosity of concretes incorporating slag, fly ash or silica fume. Cem Conc Compos 17(2):125–133

    Google Scholar 

  • Richardson A, Coventry K, Bacon J (2011) Freeze/thaw durability of concrete with recycled demolition aggregate compared to virgin aggregate concrete. J Clean Prod 19(2–3):272–277

    Google Scholar 

  • Rutherford JH, Langan BW, Ward MA (1994) Use of control specimens in freezing and thawing testing of concrete. Cem Concr Aggr 16(1):78–82

    Google Scholar 

  • Sabet FA, Libre NA, Shekarchi M (2013) Mechanical and durability properties of self consolidating high performance concrete incorporating natural zeolite, silica fume and fly ash. Constr Buil Mater 44:175–184

    Google Scholar 

  • Sabir B (1997) Mechanical properties and frost resistance of silica fume concrete. Cem Concr Compos 19(4):285–294

    Google Scholar 

  • Shang HS, Song Y (2006) Experimental study of strength and deformation of plain concrete under biaxial compression after freezing and thawing cycles. Cem Concr Res 36(10):1857–1864

    Google Scholar 

  • Shang H-S, Yi T-H, Song Y-P (2012) Behavior of plain concrete of a high water-cement ratio after freeze-thaw cycles. Materials 5(9):1698–1707

    Google Scholar 

  • Shang H-S, Cao W-Q, Wang B (2014) Effect of fast freeze-thaw cycles on mechanical properties of ordinary-air-entrained concrete. Sci World J 2014:923032

    Google Scholar 

  • Sun M, Xin D, Zou C (2019) Damage evolution and plasticity development of concrete materials subjected to freeze-thaw during the load process. Mech Mater 139:103192

    Google Scholar 

  • Tian W, Han N (2016) Evaluation of damage in concrete suffered freeze-thaw cycles by CT technique. J Adv Conc Technol 14(11):679–690

    Google Scholar 

  • Wardeh G, Ghorbel E (2015) Prediction of fracture parameters and strain-softening behavior of concrete: effect of frost action. Mater Struct 48(1–2):123–138

    Google Scholar 

  • Yang X, Wang G, Gao S, Song M, Wang A (2019) Equation for the degradation of uniaxial compression stress of concrete due to freeze-thaw damage. Adv Mater Sci Eng 2019:8603065

    Google Scholar 

  • Zhang S, Zhao B (2013) Research on the performance of concrete materials under the condition of freeze-thaw cycles. Eur J Environ Civ Eng 17(9):860–871

    Google Scholar 

  • Zhou Z-Y, Mihashi H (2008) Micromechanics model to describe strain behavior of concrete in freezing process. J Mater Civ Eng 20(1):46–53

    Google Scholar 

Download references

Acknowledgement

Not Applicable.

Funding

Not Applicable.

Author information

Authors and Affiliations

  1. Department of Civil Engineering, Isfahan University of Technology (IUT), Isfahan, Iran

    Davood Mostofinejad, Bahareh Nader Tehrani & S. Mahdi Hosseinian

  2. Department of Civil Engineering, University of Sherbrooke, Sherbrooke, Canada

    Seyed Mohammad Hosseini

Authors
  1. Davood Mostofinejad
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Seyed Mohammad Hosseini
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Bahareh Nader Tehrani
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S. Mahdi Hosseinian
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Seyed Mohammad Hosseini.

Ethics declarations

Conflict of interest

The authors declare that they have no conflict of interest.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Mostofinejad, D., Hosseini, S.M., Nader Tehrani, B. et al. Empirical Models for Prediction of Frost Resistance of Normal- and High-Strength Concretes. Iran J Sci Technol Trans Civ Eng 45, 2107–2131 (2021). https://doi.org/10.1007/s40996-020-00574-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s40996-020-00574-8

Keywords

Search

Navigation