Abstract
l-Lysine is an essential amino acid with high commercial importance, as it has to be available in sufficient quantities in animal and human feeds to meet their nutritional requirement. As there is constant increase in l-lysine demand every year, to meet the increasing demand it is necessary to produce l-lysine in large scale. Generally, l-lysine is produced by batch fermentation. In the present investigation, different fermentation process parameters such as fermentation time, pH, temperature, glucose concentration, airflow rate and aeration rate were studied to optimize the production of l-lysine by Corynebacterium glutamicum MH 20-22 B in a 5 L laboratory-scale stirred tank bioreactor. A comparative study of l-lysine production with free cells and immobilized cells of C. glutamicum MH 20-22 B was also investigated to determine whether free cells or immobilized cells were advantageous for production of l-lysine. In this way, optimized fermentation upstream parameters which produced the maximum yield of l-lysine were developed and it was also concluded from the present study that immobilized cells of C. glutamicum MH 20-22 B were more advantageous for l-lysine production as they yield more l-lysine compared to free cells of C. glutamicum MH 20-22 B. It was observed in the present study that the optimum values of fermentation time, pH, temperature, glucose concentration, airflow rate and aeration rate were 96 h, 7.5, 30 °C, 90 g/l, 1.0 vvm and 200 rpm, respectively, by immobilized cells, whereas in case of free cells the optimum values were 72 h, 7.5, 30 °C, 80 g/l, 1.25 vvm and 300 rpm. Immobilized C. glutamicum MH 20-22 B cells exhibited greater l-lysine production of 31.58 g/l than free cells which produced 26.34 g/l of l-lysine.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
Introduction
Amino acids have long played a vital role in both human and animal nutrition and health maintenance (Bercovici and Fuller 2007). With the advent of new applications and the steadily growing market demand of amino acids, their production technology has made an enormous progress during the second half of the twentieth century. Fermentation and enzymatic catalysis are the two biotechnological processes which posses both ecological and economical advantage and are the main reason for the spectacular growth of the amino acid industry. The feed amino acids l-lysine, dl-methionine, l-threonine, and l-tryptophan contribute the largest share (56 %) of the total amino acid market, approximately US$ 4.5 billion (Leuchtenberger et al. 2005). Low-cost fermentation processes have been developed for different kinds of amino acids and the current rapid progress in biotechnology, including biochemical engineering technology, strain improvement along with downstream processing, indicates that the fermentation process is the key role in the amino acid industry. Over a period of time, fermentation technology has played a vital role and recently amino acids produced by fermentation processes are the main products of biotechnology in value and volume (Ikeda 2003).
l-Lysine (C6H14N2O2; MW 146.19) is one of the essential, commercial and important amino acid which is produced on large scale by the amino acid industry. l-lysine is generally produced in purity higher than 98.5 % in stable and non-hygroscopic hydrochlorinated form (Fechter et al. 1997). l-Lysine has a number of applications in the food, pharmaceutical, feed milling and cosmetics industries, and its current price is approximately US$ 3–4/kg. The production costs of l-lysine have been lowered because of continuous optimization of the fermentation process. 80 % of lysine in the world market is synthesized by microbial fermentation and the remaining 20 % by chemical synthesis. Thus, the scope for l-lysine production in the amino acid industry is more because of its increasing market demand (Anastassiadis 2007). The raw materials used in the fermentation process for the production of l-lysine are biologically and naturally available, and the by-products produced during l-lysine fermentation are non-toxic and have high commercial value. The microbes separated from the broth contain more than 50 % of proteins, which are used in animal feed. Organic and inorganic nitrogen compounds, phosphorus compounds and potassium salts, which could be used as fertilizers, are also produced in the spent broth during l-lysine production (Anastassiadis 2007).
Microbial strains such as Brevibacterium lactofermentum (Fechter et al. 1997), Brevibacterium flavum (Ikeda 2003) and C. glutamicum (Anastassiadis 2007) have been used for the past 50 years for large-scale production of l-lysine, but the sole production organism for l-lysine is C. glutamicum and its subspecies. l-Lysine is produced by an aerobic fermentation process using C. glutamicum, which is a rod-shaped, fast-growing, non-sporulating, Gram-positive and nonpathogenic coryneform bacterium (Kinoshita et al. 1957; Udaka 1960). The ability of C. glutamicum to produce other amino acids, such as l-threonine (Nakayama and Kase 1974), l-methionine (Kase and Nakayama 1975), l-serine (Eggeling 2007), l-histidine (Araki et al. 1974), l-valine (Ruklisha et al. 2007), l-tryptophan (Ikeda 2006), l-phenylalanine and l-tyrosine (Ikeda and Katsumata 1992), l-leucine (Patek 2007) and l-isoleucine (Guillout et al. 2002), has made it an important organism in industrial biotechnology. Large-scale production of l-lysine by fermentation with C. glutamicum started in 1958 at Kyowa Hakko’s plant in Japan. The biotechnological production of l-lysine has been constantly improved by fermentation process optimization and strain improvement (Pfefferle et al. 2003). Fermentation time, pH, temperature, glucose concentration, airflow rate and aeration rate are the most important factors in fermentation processes. However, there have been very few reports on fermentation process optimization. Hence, the main objective of this paper is to study l-lysine production by fermentation of free and immobilized cells using different culture parameters.
Materials and methods
C. glutamicum MH 20-22 B, which is a leucine auxotroph, was employed throughout this study. C. glutamicum MH 20-22 B was donated by Professor Eggeling, Biotechnology Institute, Julich, Germany. It was cultured on agar slopes using nutrient agar medium containing peptone (5 g), beef extract (3 g), NaCl (5 g), agar (15 g) and distilled water (1,000 ml). The pH was maintained at 7.0. The composition of the media used in the fermentation process was as follows:
Rich medium
Glucose (10 g), yeast extract (10 g), peptone (10 g), NaCl (2.5 g) and distilled water (1.0 L); the pH was maintained at 7.0.
Inoculum medium
CaCl2·2H2O (1 g), (NH4)·2SO4 (30 g), MgSO4·7H2O (0.4 g), NaCl (0.05 g), MnSO4·H2O (0.0076 g), FeSO4·7H2O (0.001 g), KH2PO4 (0.5 g), K2HPO4 (0.5 g), Urea (2 g), yeast extract (1 g), peptone (1 g), d-glucose (10 g), thiamine (0.2 mg), d-biotin (0.5 mg) and distilled water (1.0 L); the pH was maintained at 7.0.
Fermentation medium
CaCl2·2H2O (1 g), (NH4)·2SO4 (30 g), MgSO4·7H2O (0.4 g), NaCl (0.05 g), MnSO4·H2O (0.0076 g), FeSO4·7H2O (0.001 g), KH2PO4 (1 g), K2HPO4 (1 g), urea (2 g), yeast extract (1.5 g), peptone (2 g), d-glucose (150 g), thiamine (0.2 mg), d-biotin (0.5 mg), l-serine (0.1 mg) and distilled water (1.0 L); the pH was maintained at 7.0.
Fermentation procedure
C. glutamicum MH 20-22 B cells were cultured on a nutrient agar strain maintenance plate at 30 °C for 24 h and inoculated into 20 ml of rich medium in a 250 ml conical flask. After 24 h of cultivation in an orbital shaker with 120 rpm at 30 °C, the seed broth was transferred to 180 ml of inoculum media in an Erlenmeyer flask and maintained in an orbital shaker for 40 h at 120 rpm and 30 °C. This was then used to inoculate the fermentation medium in the stirred tank bioreactor. Batch fermentation experiments were carried out at different parameters to optimize the upstream parameters for free cells and immobilized cells.
Immobilization method
Growth medium composition
Glucose (2 g), beef extract (1 g), Bacto Peptone (1 g), NaCl (0.25 g), agar (2 g) and distilled water (100 ml) were maintained at pH 7.0. Agar slants of C. glutamicum MH 20-22 B which were grown for 24 h were used to inoculate 50 ml of growth medium (and kept on shaker for 48 h (150 rpm) at 30 °C. 100 ml of 72 h-old culture was used to prepare immobilized beads of calcium alginate. 15 % volume of beads were employed throughout this study. Immobilization of C. glutamicum MH 20-22 B cells was done in strict aseptic conditions. Gluteraldehyde entrapment method using cross-linked calcium alginate was used to immobilize C. glutamicum MH 20-22 B cells (Jetty et al. 2005; Marek et al. 1985). 100 µl gluteraldehyde and 3 % sodium alginate were thoroughly mixed with 0.06 % cells on dry cell weight basis (DCW) (w/v) to get uniform suspension. This uniform suspension was transferred into 0.2 M CaCl2 solution using a peristaltic pump through a cut micropipette tip (or) orifice. The curing of the formed beads was done by incubating in 0.2 M CaCl2 solution for 24 h. The beads were washed twice with sterile saline solution (0.9 % NaCl solution (w/v)) and preserved at 4 °C in saline solution for further use.
Sterilization of the stirred tank bioreactor
Initially, all reactor parts were separated. All parts were washed with distilled water thoroughly and again with acetone before sterilization. After washing with distilled water, all the above parts were wrapped with aluminum foil before placing in the autoclave. All these accessories were kept in the autoclave, which was operated at a temperature of 120 °C and a pressure of 15 psi for a period of 20 min.
Fermentation studies
Batch or fed-batch processes are employed for the commercial production of amino acids. In batch operations all of the nutrients are added at the beginning. Moreover, in batch fermentations microorganisms grows until one or more of essential nutrients get exhausted or until fermentation conditions such as oxygen limitation, pH decrease and product inhibition become unfavorable. In this present investigation, fermentation experiments with free cells and immobilized cells of C. glutamicum MH 20-22 B were conducted with different fermentation parameters at batch mode using a sterilized continuous stirred tank bioreactor of 5 L capacity. For experiments with immobilized cells of C. glutamicum, a fermentation medium containing 60 g of immobilized beads (15 %) was used throughout the experiments. Beads containing 3.0–3.5 mm range of diameter were used. Different parameters with different variations were studied, and variations in the particular parameter were made as per the previous experiments and literature.
Analytical methods
l-Lysine in the supernatant fluid was quantitatively estimated by the acidic ninhydrin method (Chinard 1952). Throughout the study, the glucose concentration was estimated by the anthrone method (Morris 1948; Neish 1952). The dry cell weight (Biomass) was determined (Kim et al. 1981).
Results and discussions
The present report describes the optimization of fermentation parameters for l-lysine production by C. glutamicum MH 20-22 B. The continuous batch fermentation described in this study also facilitated the analysis of the various parameters affecting l-lysine fermentation. Earlier, many investigators have reported about multistage continuous fermentation processes and their difficulties in running continuous l-lysine production systems (Becker 1982; Michalski et al. 1984). To determine the suitable conditions for l-lysine production by free and immobilized cells of C. glutamicum in a stirred tank bioreactor, the parameters investigated are l-lysine concentration, biomass concentration, residual glucose concentration and glucose utilized with variations in fermentation time, temperature, pH, substrate concentration (glucose), aeration and agitation rate.
Effect of fermentation time on l-lysine production by free cells
The effect of fermentation time on l-lysine production by free cells of C. glutamicum MH 20-22 B was studied maintaining the operating conditions as temperature of 28 °C, pH 7.0, air flow rate 1.5 vvm, agitation rate 300 rpm and glucose concentration 100 (g/l). It was analyzed from Fig. 1 that as the fermentation time increased, the concentration of the residual glucose decreased from 34.13 to 18.80 g/l between 48 and 72 h and the product concentration also increased from 12.3 to 18.7 g/l with biomass concentration from 6.11 to 9.1 g/l. Similar studies were carried out by Ekwealor and Obeta (2005) for the production of lysine using Bacillus megaterium free cells. As the fermentation proceeded further, the glucose consumption and l-lysine production increased and reached the maximum at 72 h, with increased sugar utilization rate and maximum l-lysine concentration of 18.7 g/l being observed (Fig. 1). After 72 h, the maximum product achieved a downward trend and l-lysine concentration and yields decreased, in spite of the increase in fermentation time due to less availability of nutrients. So a fermentation time of 72 h was most suitable for the production of l-lysine using C. glutamicum MH 20-22 B free cells. Hadj Sassi et al. (1988) studied the yield of l-lysine (Yp/s) by C. glutamicum in a fed-batch reactor using free cells, and the maximum yield was 0.21 (g/g).
Effect of fermentation time on l-lysine production by free cells
Effect of temperature on l-lysine production by free cells
The growth rate of bacterial microorganisms is strongly dependent on temperature during fermentation which changes the whole metabolism. In this present study, an attempt has been made to study the effect of different temperature ranges (27–32 °C) on l-lysine production carried out in a stirred tank reactor. The temperature profile on l-lysine production was done using C. glutamicum MH 20-22 B free cells under operating conditions such as fermentation time of 72 h, pH 7.0, air flow rate 1.5 vvm, agitation rate 300 rpm and glucose concentration 100 g/l. Any change in the temperature can alter the substrate utilization rate of microorganism, which leads to unbalanced nutrients in the medium with respect to the growth rate of the C. glutamicum cells. If any of the crucial nutrients is exhausted soon or unused, this can make the growth in culture from balanced to unbalanced and results in performance change. At 30 °C, maximum l-lysine concentration of 21.31 (g/l) was obtained along with 18.24 g/l of maximum biomass (Table 1). Glucose utilization was also high at 30 °C. An increase in temperature resulted in decreased productivity, which suggested that a small increase in temperature has a profound effect on cellular activities, such as repression of metabolic enzymes. Hilliger et al. (1984) observed the influence of temperature as one of the major fermentation parameters on growth and l-lysine formation by C. glutamicum. They studied l-lysine production at different temperatures which showed that biomass and l-lysine concentration was high at 30 °C, whereby temperatures exceeding 32 °C reduced the specific l-lysine formation rate and the substrate conversion yield coefficient. Hence, a temperature of 30 °C was optimum temperature for l-lysine fermentation by both free and immobilized cells of C. glutamicum MH 20-22 B.
Effect of pH on l-lysine production by free cells
In microbial fermentations, pH is a very important and strongly influencing factor. Basic compounds, such as ammonium hydroxide, potassium hydroxide, sodium hydroxide, calcium carbonate, ammonia and gaseous ammonia and urea, inorganic acid compounds such as sulfuric or phosphoric acid and organic acids are utilized for controlling pH in l-lysine cultures ranging from 5.0 to 9.0 (Nakamura et al. 2000). The effect of pH was found to be a very significant parameter in l-lysine yield. The pH effect on l-lysine production was investigated under operating conditions such as fermentation time of 72 h, temperature of 30 °C, air flow rate of 1.5 vvm, agitation rate of 300 rpm and glucose concentration rate of 100 g/l. From Table 2, it may be analyzed that the optimum pH for C. glutamicum MH 20-22 B free cells is 7.5, with the maximum lysine concentration of 22.58 (g/l). At 7.5 pH the biomass production was also high at 17.85 g/l. Broer et al. (1993) also reported that the optimum pH for maximum velocity transport of C. glutamicum was 7.4–7.8. To maintain optimal pH, reagents such as calcium carbonate must be added to the culture medium at the beginning of fermentation. Thus, calcium carbonate was used as an internal neutralizing agent. Though the pH of the fermenter was automatically controlled by ammonia water, a small amount of CaCO3 must be added (Wang et al. 1991). It eliminates the lag phase of cell growth, thereby shortening fermentation time. Therefore 7.0 was considered as an optimum pH for all the experiments.
Effect of glucose concentration on l-lysine production by free cells
In fermentation, the cell concentration and substrate concentration play major roles in the overall performance of the process for l-lysine production. The cells use available substrate immediately if the process conditions in the reactor are favorable. The viability and growth of the cells are very much dependent on the substrate availability in the reactor. l-Lysine-producing bacteria can utilize various carbon sources, such as glucose, fructose, sucrose and maltose. The effect of substrate on the l-lysine yield was expressed on the basis of lysine produced per unit substrate consumed. The effect of glucose concentration on l-lysine production by free cells of C. glutamicum MH 20-22 B was studied by carrying fermentation under conditions of pH 7.5, fermentation time 72 h, temperature 30 °C, air flow rate 1.5 vvm, agitation rate 300 rpm and different ranges of glucose concentrations of 70, 80, 90, 100, 110 and 120 (g/l).
Glucose concentration on l-lysine production was investigated by Hirose and Shibai (1985) and it was found that higher concentration of glucose inhibited bacterial growth along with low yield. For this purpose, the effects of different concentrations of glucose on l-lysine production were examined. Different l-lysine batch fermentations were conducted at different initial glucose concentrations. From different batches, it was apparent that lysine production was cell growth associated and this was clearly confirmed. From Table 3 the maximum l-lysine concentration of 20.1 (g/l) is observed at glucose concentration of 80 g/l for C. glutamicum MH 20-22 B free cells and any excessive substrate concentration present in the fermentation broth leads to reduction in the product concentration because of substrate inhibition. (Hadj Sassi et al. 1988) reported that the initial concentration of glucose influenced the production of l-lysine by Corynebacterium Sp. in batch culture and found that the specific production rate was obtained at 65 g/l of glucose. However, it was observed that pH and substrate concentration had significant effect in comparison to temperature.
Effect of airflow rate on l-lysine production by free cells
The air supply in submerged cultures is known to have an important influence on microbial production of amino acids (Akashi et al. 1979). Thus, oxygen has been shown to play an important and crucial role in the regulation of both intermediary metabolism and biomass formation coupled with alteration of l-lysine synthesis and with a change of l-lysine yield, respectively. To find the optimum value of air flow rate for free cells of C. glutamicum MH 20-22 B, experimental studies were conducted in a batch-stirred tank reactor in the bioreactor under conditions of pH 7.5, fermentation time 72 h, temperature 30 °C, agitation rate 300 rpm, glucose concentration 80 g/l and the aeration rate maintained at different ranges from 0.25 to 1.5. Table 4 shows the characteristic batches of l-lysine fermentation at a range of 0.25–1.5 volume air per volume of medium per minute (vvm). The best air flow rate for l-lysine production by free cells was 1.25 vvm, the product concentration was 20.54 g/l and the biomass productivity was 19.34 g/l. Glucose utilized was 80.66 g/l at 1.25 vvm. So 1.25 vvm was considered as the optimum airflow rate for C. glutamicum MH 20-22 B free cells. Wang et al. (1991) performed fermentation of l-lysine on a rotary shaker at 200 rpm and suggested that the optimum air flow rate of l-lysine production was 1.0 vvm or above 1.0 vvm, approximately.
Effect of agitation rate on l-lysine production by free cells
Agitation and aeration in a stirred tank bioreactor always cause foaming. Excess foaming forces the broth out of the bioreactor and contaminates the system quickly. Optimum aeration must be maintained, as agitation minimizes foaming and maximizes the specific production rate. In the bioreactor, the fermentation medium was agitated to provide homogeneity across the vessel. l-lysine production at different agitation rates of 100, 150, 200, 300, 350 and 400 rpm and under different conditions such as pH 7.5, fermentation time 72 h, temperature 30 °C, aeration rate 1.25 vvm and glucose concentration 80 g/l was examined to find out the optimum agitation rate for l-lysine production by free cells of C. glutamicum MH 20-22 B. From Table 5, we can observe that the maximum l-lysine concentration is 26.34 g/l and the biomass is 17.13 g/l at 300 rpm. Therefore, the optimum agitation rate for l-lysine production was 300 rpm for free cells. Shah et al. (2002) studied the influence of dilution in the range between 50 and 300 rpm and concluded that after 200 rpm l-lysine production was levelled off.
Production of l-lysine by immobilized cells of C. Glutamicum
Effect of fermentation time on l-lysine production by immobilized cells
Studies on the effect of fermentation time on l-lysine production by immobilized C. glutamicum MH 20-22 B cells were carried out under different fermentation conditions, such as temperature 28 °C, pH 7.0, air flow rate 1.5 vvm, agitation rate 300 rpm and glucose concentration 100 (g/l). From Fig. 2, it may be analyzed that l-lysine concentration is relatively low over the first 2 (48 h) days. l-lysine accumulation was 20.1 g/l at 72 h and later increased to 23.4 g/l at 96 h. The biomass concentration was 15.07 g/l at 96 h. After 96 h, an important observation was the lower glucose concentration of 10.15 g/l, which further decreased as the fermentation process proceeded. l-lysine production decreased due to the depletion of nutrients in the fermentation medium. The results presented in Fig. 2 show that l-lysine production is good at 96 h, which is the best fermentation time for the production of l-lysine by immobilized cells of C. glutamicum MH 20-22 B.
Effect of fermentation time on l-lysine production by immobilized cells
Effect of temperature on l-lysine production by immobilized cells
The effect of temperature on l-lysine production by immobilized cells of C. glutamicum MH 20-22 B was studied under different operating conditions such as fermentation time of 96 h, pH 7.0, air flow rate 1.5 vvm, agitation rate 300 rpm and glucose concentration 100 g/l. The results from Table 6 show that l-lysine concentration of 24.45 g/l, biomass of 19.45 g/l and glucose utilization of 95.67 g/l, which were maximum compared to all temperatures, were observed at 30 °C. Therefore, 30 °C temperature was most suitable for the production of l-lysine by C. glutamicum MH 20-22 B. The downtrend of residual glucose as the temperature increases can be seen in Table 6. After 30 °C, the l-lysine and biomass concentrations were decreased. Therefore, 30 °C was the optimum temperature for l-lysine production by immobilized cells of C. glutamicum MH 20-22 B.
Effect of pH on l-lysine production by immobilized cells
The growth rate of microorganism is usually very sensitive to variation in pH. Furthermore, the process of growth changes the pH of the medium; therefore, the effect of different pH values on l-lysine production was examined in a stirred tank bioreactor. The pH profile of immobilized cells of C. glutamicum MH 20-22 B was studied by carrying fermentation under conditions such as fermentation time of 96 h, temperature 30 °C, air flow rate 1.5 vvm, agitation rate 300 rpm and glucose concentration 100 g/l. The pH ranges were maintained from 6 to 8.5. The different pH values (6–8.5) of the production medium were adjusted with 2 M HCl and 1 M NaOH. Table 7 shows that the maximum l-lysine concentration of 25.62 (g/l) and biomass of 20.42 (g/l) were obtained at pH of 7.5 for immobilized cells of C. glutamicum MH 20-22 B. Table 7 also shows that as the pH increases, the residual glucose concentration decreases. When compared with all pH ranges, 7.5 was the best pH for l-lysine production with immobilized cells.
Effect of glucose concentration on l-lysine production by immobilized cells
In the bioreactor, the cell concentration and glucose concentration play a major role in the overall performance of the process for l-lysine production. The cells use available glucose immediately if the process conditions in the reactor are favorable. The viability and growth of the cell are very much dependent on the glucose availability in the bioreactor. For this purpose, different glucose concentrations [70, 80, 90, 100, 110 and 120 (g/l)] were employed under different conditions such as pH 7.5, fermentation time 96 h, temperature 30 °C, air flow rate 1.5 vvm and agitation rate 300 rpm to determine its effect on l-lysine production. The maximum concentrations of l-lysine of 26.59 g/l and biomass of 19.68 g/l were obtained at 90 g/l glucose concentration in spite of low residual concentration (Table 8). Glucose concentration of 90 g/l was found to be effective in terms of l-lysine production with immobilized cells of C. glutamicum MH 20-22 B.
Effect of aeration rate on l-lysine production by immobilized cells
The oxygen supply is greatly vital for the fermentation process. Oxygen, an extremely important nutrient, is usually supplied to the reactor by an air pump. Experimental studies were conducted in a batch-stirred tank reactor to find the optimum value of air flow rate for C. glutamicum MH 20-22 B in the bioreactor under conditions of pH 7.5, fermentation time 96 h, temperature 30 °C, agitation rate 300 rpm, glucose concentration 90 g/l and the aeration rate maintained at different ranges from 0.25 to 1.5. The maximum concentrations of l-lysine of 26.85 g/l and biomass of 20.93 g/l were obtained at an optimum air flow rate of 1.0 vvm for stirred tank bioreactor (Table 9). The maximum product concentration, biomass and glucose utilized were good at the flow rate of 1.0 vvm. Therefore, the optimum air flow rate for l-lysine production was found to be 1.0 vvm.
Effect of agitation rate on l-lysine production by immobilized cells
Experimental studies to know the agitation profile of immobilized cells of C. glutamicum MH 20-22 B for better production of l-lysine were done by carrying out fermentation under different conditions such as pH 7.5, fermentation time 96 h, temperature 30 °C, aeration rate 1.0 vvm, glucose concentration 90 g/l and the agitation varied from ranges 100 to 400. In the bioreactor, a stirrer is present to maintain uniform composition throughout the vessel. Maximum l-lysine concentration and yield observed at 200 rpm were 31.58 g/l and biomass of 17.72 g/l, respectively (Table 10). Therefore, the optimum agitation rate for l-lysine production was 200 rpm for immobilized cells of C. glutamicum MH 20-22 B. Table 11 illustrates the optimized fermentation parameters for free cells and immobilized cells of C. glutamicum MH 20-22 B. The results obtained here indicate that l-lysine can be produced efficiently by immobilized growing C. glutamicum MH 20-22 B cells. By comparison with the results obtained with free cells, there is a significant improvement concerning the accumulation of l-lysine by immobilized growing cells.
Conclusion
To improve the production rate of l-lysine, free and immobilized cell of C. glutamicum MH 20-22 B were analyzed under various process conditions. It was observed that the optimum values of fermentation time, pH, temperature, glucose concentration, airflow rate and aeration rate were 96 h, 7.5, 30 °C, 90 g/l, 1.0 vvm and 200 rpm, respectively, by immobilized cells. whereas in case of free cells the optimum values were 72 h, 7.5, 30 °C, 80 g/l, 1.25 vvm and 300 rpm. Immobilized C. glutamicum MH 20-22 B cells exhibited greater l-lysine production of 31.58 g/l than free cells, which produced 26.34 g/l of l-lysine. The results obtained here indicate that l-lysine can be produced efficiently by immobilized growing C. glutamicum MH 20-22 B cells by comparison with the results obtained with free cells in a stirred tank bioreactor.
References
Akashi S, Shibai H, Hirose Y (1979) Effect of oxygen supply on l-lysine, l-threonine and l-isoleucine fermentations. Trends Biochem Sci 43:2087
Anastassiadis S (2007) l-Lysine Fermentation. Recent Pat Biotechnol 1(1):11–24
Araki K, Kato F, Aral Y, Nakayama K (1974) Histidine production by auxotrophic histidine analog-resistant mutants of Corynebacterium glutamicum. Agric Biol Chem 38:837
Becker MJ (1982) Product biosynthesis in continuous fermentation. Folia Microbiol 27:315–318
Bercovici D, Fuller MF (2007) Industrial amino acids in nonruminant animal nutrition. In: Wallace RJ, Chesson A (eds) Biotechnology in animal feeds and animal feeding. Wiley, Weinheim. doi:10.1002/9783527615353.ch6
Broer S, Eggeling L, Kraemer R (1993) Strains of Corynebacterium glutamicum with different lysine productivities may have different lysine excretion systems. Appl Env Microbiol 59:316
Chinard FP (1952) Photometric estimation of proline and ormithine. J Biol Chem 199:91–95
Eggeling L (2007) l-Serine and Glycine. In: Amino acid biosynthesis pathway, regulation and metabolic engineering. Springer, Berlin, vol 5, pp 259–272
Ekwealor A, Obeta JAN (2005) Studies on lysine production by Bacillus megaterium. Afr J Biotechnol 4:633–638
Fechter WL, Dienst JH, Le Patourel JF (1997) US5684190
Guillout S, Rodal AA, Lessard PA, Sinskey AJ (2002) Methods for producing l-isoleucine. USA patent (US 6451564)
Hadj Sassi A, Fauvart L, Deschamps AM, Lebeault JM (1988) Fed batch production of l-lysine by Corynebacterium glutamicum. Biochem Eng J 1:85–90
Hilliger M, Haenel F, Menz J (1984) Influence of temperature on growth and l-lysine formation in Corynebacterium glutamicum. J Appl Microbiol 24:437–441
Hirose Y, Shibai H (1985) l-Glutamic acid fermentation. Compr Biotechnol 3:595–600
Ikeda M (2003) Amino acid production processes. Adv Biochem Eng Biotechnol 79:1–35
Ikeda M (2006) Towards bacterial strains overproducing l-tryptophan and other aromatics by metabolic engineering. Appl Microbiol Biotechnol 69:615–626
Ikeda M, Katsumata R (1992) Metabolic engineering to produce tyrosine or phenylalanine in a tryptophan producing Corynebacterium glutamicum strain. Appl Environ Microbiol 58:781–785
Jetty A, Gangagni Rao A, Sarva Rao B, Madhavi G, Ramakrishna SV (2005) Comparative studies of ALR and FBR for streptomycin production by immobilized cells of Streptomyces sp. Chem Biochem Eng 19:179–184
Kase H, Nakayama K (1975) Fermentation production of l-methionine and regulation of l-methionine biosynthesis in Corynebacterium glutamicum. Agric Biol Chem 39:153–160
Kim BH, Seong bL, Mheen TI, Han MH (1981) Studies on microbial penicillin amidase, optimization of the enzyme production from Escherichia coli. Korean J Appl Micobiol Bioeng 9:29
Kinoshita S, Udaka S, Shimono M (1957) Amino acid fermentation. I. Production of l-glutamic acid by various microorganism. J Gen Appl Microbiol 3:193–205
Kinoshita S, Nakayama K, Akita S (1958) Taxonomical study of glutamic acid accumulating bacteria, Micrococcus glutamicus. Agric Chem Soc Jpn 22:176
Leuchtenberger W, Huthmacher K, Drauz K (2005) Biotechnological production of amino acids and derivatives: current status and prospects. Appl Microbiol Biotechnol 69(1):1–8
Marek PJ, Kierstan M, Coughlan MP (1985) Immobilized cells and enzymes. Practical approaches UK. Ireland press limited, Ireland, pp 43–44
Michalski HJ, Krzystek L, Blazczyk R, Jamroz T, Wieczorek A (1984) The effect of mean residence time and aeration intensity on the l-Lysine production in a continuous culture. In: Third Europian congress on biotechnology, München, FRG, vol 2. Verlag Chemie, Weinheim, pp 527–532
Morris DL (1948) Microbial physiology. Wiley, New York
Nakamura T, Nakayama T, Koyama Y, Shimazaki K, Miwa H, Tsuruta M, Tamura K, Tosaka O (2000) l-Lysine fermentation (US20006025169)
Nakayama K, Kase H (1974) Studies on l-threonine fermentation and Mechanism of l-threonine and l-lysine production by analog-resistant mutants of Corynebacterium glutamicum. Agric Biol Chem 38:993–1000
Neish AC (1952) Analytical methods for bacterial fermentations. Report 46-8-3, 2nd revision. National Research Council of Canada, Saskatoon, Canada
Patek M (2007) Branched chain amino acids biosynthesis pathways, regulation and metabolic engineering. Springer, Heidelberg
Pfefferle W, Moeckel B, Bathe B, Marx A (2003) Biotechnological manufacture of l-lysine. In: Scheper T (ed) Advances in biochemical engineering, vol 79. Springer, Berlin, p 59
Ruklisha M, Paegle L, Denina I (2007) l-Valine biosynthesis during batch and fed batch cultivations of Corynebacterium glutamicum: relationship between changes and bacterial growth rate and intracellular metabolism. Progr Biochem 42:634–640
Shah AH, Hameed A, Khan GM (2002) Fermentative production of l-lysine, bacterial fermentation. J Med Sci 2:152–157
Udaka S (1960) Screening methods for microorganisms accumulating metabolites and its use in the isolation of Micrococcus glutamicus. J Bacteriol 79:754
Wang JS, Kuo YC, Chang CC, Liu YT (1991) Optimization of culture conditions of l-lysine fermentation by Brevibacterium species. Nat Biotechnol 68:154–159
Acknowledgments
The authors are grateful to NATCO for all their encouragement in the fermentation studies.
Conflict of interest
We declare that there is no conflict of interest regarding the publication of this article.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and the source are credited.
About this article
Cite this article
Razak, M.A., Viswanath, B. Optimization of fermentation upstream parameters and immobilization of Corynebacterium glutamicum MH 20-22 B cells to enhance the production of l-lysine. 3 Biotech 5, 531–540 (2015). https://doi.org/10.1007/s13205-014-0252-7
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13205-014-0252-7