Abstract
One of the essential issues in the quality management of water resources is the determination of the level of eutrophication and dissolved oxygen in dam reservoirs and other water bodies. It is possible to study changes in dissolved oxygen concentration using qualitative models. In this study, CE-QUAL-W2, a two-dimensional model of hydrodynamics and water quality capable of predicting the behavior of aquatic ecosystems, has been used to simulate dissolved oxygen concentration and eutrophication. As a case study, the water quality of the Yamchi dam reservoir, located in Ardabil Province, has been qualitatively investigated using the CE-QUAL-W2 model. Based on the geographical location of the Yamchi dam reservoir, it includes warm monomictic basins. According to the results, the dissolved oxygen concentration in the simulation period varied between 0 and 12 mg/L. In autumn and winter, this concentration was almost uniform at various depths. However, in summer, a sharp decrease in dissolved oxygen concentration, to less than 2 mg/L in the bottom layers, was observed, which is due to the presence of nutrients. Regarding eutrophication, the Yamchi dam reservoir is one of the eutrophic reservoirs, and practical strategies should be employed to improve these conditions. Recommended strategies include reducing the retention time of water in the reservoir, dewatering from the underlying layers during the thermal stratification period, and preventing the entry of agricultural drains into the inlet tributaries of the reservoir.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
Introduction
Due to the economic, social, and industrial growth of societies, the water in rivers, estuaries, and natural lakes, in terms of quantity, quality, and geographical distribution, no longer meets human needs. In order to overcome this problem, several dams were constructed all over the world. The construction and operation of dams have physical, chemical, and biological effects on the rivers. These effects have both positive and negative aspects, such as flood control, hydropower generation, water supply for agricultural and drinking sectors, as well as profound influences on the aquatic environment, including changes in the qualitative structure of outgoing water (Yigzaw et al. 2019; Khonok et al. 2021). One of the critical issues related to the operation and environment of dam reservoirs is the prediction of the quality of reservoir water and its outflow during operation. Increased water nutrients, i.e., eutrophication, in reservoirs results in a sharp drop in dissolved oxygen concentration, water quality, and its inability to meet the various environmental needs that endanger the aquatic life of the river downstream ecosystem. This phenomenon decreases the water quality and increases sedimentation in the reservoir by increasing the growth of algae and aquatic plants in reservoirs, thus reducing the amount of dissolved oxygen in water (Sun et al. 2022; Oliveira et al. 2020; and Yigzaw et al. 2019). Ma et al. (2008) examined the thermal stratification in the Kouris dam reservoir in Cyprus using the CE-QUAL-W2 qualitative two-dimensional model. They showed that this reservoir has thermal stratification most of the year, while a mixing occurs in the reservoir in early February. Meteorological parameters are the crucial parameters that affect this phenomenon in the reservoir. They then investigated the effect of selective dewatering on thermal stratification in the dam reservoir by defining water withdrawal scenarios from various water elevations and concluded that water withdrawal scenarios did not affect the reservoir stratification pattern during the year. The reason was the relatively small volume of water withdrawal from the dam. However, the outflow of water from the deeper layers was able to facilitate the heat transfer from the surface to the depth (Ma et al. 2008). Chai et al. (2014) studied the simulation of the Heihe reservoir in Xian city, China, in terms of pollution characteristics due to thermal stratification and found that this reservoir has a stable thermal stratification, and the lower layers lack oxygen in summer. The main qualitative problem of the reservoir is the release of pollutants from sediments. Therefore, to disrupt the stratification, aeration of the bed has been suggested to improve water quality (Chai et al. 2014). Ebrahimi et al. (2015) studied the simulation of thermal and salinity stratification in the Baft dam reservoir, Iran, using the CE-QUAL-W2 software. They showed that thermal stratification occurs in nine months of the year, starting in April and peaks in August and September, and there is a correlation between salinity and thermal stratifications. The maximum salinity is 307 mg/L, indicating a favorable condition of the Baft dam reservoir in terms of drinking and agricultural water compared to the optimum salinity threshold (500 mg/L) (Ebrahimi et al. 2015). Sabeti et al. (2017) simulated the thermal and salinity stratification of the Mamloo dam using the CE-QUAL-W2 model. The results showed that the reservoir experiences a vertical mixing in summer and a radiant slope in winter. Also, thermal and salinity stratification prevail at the same time. Moreover, the thermal stratification decreases, and the temperature intensity increases in summer (Sabeti et al. 2017). Rahimi Movaghar et al. (2019) modeled the temperature conditions, dissolved oxygen concentration, and total dissolved solids (TDS) in the Shahid Rajaee dam reservoir, Mazandaran Province. They studied the effects of reducing the input TDS to the reservoir under two scenarios: a 20% reduction in the input TDS in both input branches (Scenario 1) and a 20% reduction in the input TDS in the main input branch (Scenario 2). They investigated the quality conditions of the reservoir according to IRWQISC. The results showed the optimal modeling with acceptable performance. The simulations indicated that TDS in the first and second scenarios was reduced by 20.0 and 14.2% in the maximum TDS conditions and 19.4 and 13.4% in the minimum TDS conditions, respectively. Subsequently, IRWQISC values showed that the water quality of the Rajaee dam reservoir is in relatively good condition (Rahimi Movaghar et al. 2019). Shabani et al. (2019) used the CE-QUAL-W2 model to investigate the thermal stratification of the Seymareh dam in Ilam Province, Iran. The modeling results determined that the dam has a period of thermal stratification, which causes the organic matter and sediment deposited in the bottom to increase gradually. Moreover, the mixing of the reservoir causes the spread of the eutrophication phenomenon. This phenomenon lasts from March to December and reaches its peak in autumn. The thickness of the surface layer of water, called epilimnion, varies from month to month. Besides, this difference in the middle layer, called the thermocline, is also seen in various months. The thickness of the epilimnion in December is more than in other months (Shabani et al. 2019). Salehi et al. (2019) investigated the water quality of the Mahabad dam reservoir located in West Azerbaijan Province using the CE-QUAL-W2 model as an efficient software for water quality analysis in reservoirs and lakes. According to the results, the Mahabad dam reservoir has a relatively strong stratification in summer that starts in late April and reaches its peak in August. With the beginning of autumn and at the same time with the decrease in radiation entering the reservoir, stratification changes into mixing in such a way that complete mixing occurs in the reservoir in December. The changes in TDS have an upward trend by increasing the depth so that the maximum concentration is at the bottom of the reservoir throughout the year. In contrast, dissolved oxygen concentration decreases by increasing the depth of the reservoir. The changes in dissolved oxygen concentration begin in June and continue until late summer, so that at this time of year, the dissolved oxygen concentration in the hypolimnion reaches zero, eventually leading to the production of unpleasant color and odor in the reservoir (Salehi et al. 2019). Talakesh et al. (2019) investigated the water quality of the Karun 3 dam reservoir, Khuzestan Province, using the CE-QUAL-W2 model. The results showed that this reservoir had only one period of thermal stratification, starting from the end of April and reaching its peak in the middle of summer. Passing through this peak and entering the cold seasons of the year, the formed stratification gradually disappears so that in March, complete mixing occurs in the reservoir. Changes in dissolved oxygen concentration also show a downward trend by increasing the depth so that its amount decreases from 7.07 to 4.37 mg/L in September. This downward trend starts in April and intensifies with the warming of the weather. This condition eventually produces an unpleasant color and odor in the reservoir (Talakesh et al. 2019). Mercy and kioko (2021) evaluated the water quality of two Maruba and Kyai earth dam in Machakos Municipality, Kenya, based on variables including pH, chlorides, EC, turbidity, nitrites, nitrates, sulfates, phosphates and TDS. The results showed that the amount of all mentioned parameters were within WHO set standard except turbidity for domestic water in both dams which was due to poor farming practices causing soil erosion and accumulation of silt within the two dam reservoirs (Mercy and Kioko. 2021).
Rezaei Barandagh et al. (2018) investigated the thermal and qualitative stratification of the Taham dam reservoir, Zanjan Province, Iran, using the CE-QUAL-W2 model. The results indicated the existence of a period of thermal stratification in the reservoir that lasts about eight months of the year. This phenomenon starts at the end of April and reaches its peak in August and September, with a 20 °C difference between the epilimnion and hypolimnion. Also, mixing was observed from January to April. In autumn, with decreasing the difference in water temperature in the upper and lower layers, the thermal stratification in the reservoir weakened and completely disappeared in winter. The results also indicated the presence of salinity stratification at the same time as thermal stratification in the reservoir (Rezaei Barandagh et al. 2018). Beiramipoor et al. (2018) conducted a qualitative study of the Baft dam constructed on the Baft River in Kerman Province, Iran, with the help of CE-QUAL-W2. Their studies showed that thermal stratification begins in late May with the onset of the heating season and peaks in August and September. This stratification continues until October, and mixing occurs in the reservoir in November and March, with decreasing water temperature (Beiramipoor et al. 2018). Kaveh et al. (2015) used the CE-QUAL-W2 model to investigate the thermal stratification and eutrophication conditions of the Ilam dam, Iran. The results indicated the presence of stratification in summer. This stratification begins with the warming of the air in the spring and reaches its most stable state in July. With the decreasing trend of temperature in the reservoir in autumn, a mixing is observed in winter, and also, the reservoir is in the mesotrophic and eutrophic state according to the Vollenweider and Kress, as well as the Newton and Ulm criteria (Kaveh et al. 2015). Kiani Sadr (2017) simulated thermal stratification and dissolved oxygen concentration of the Garsha dam reservoir, Kermanshah Province, Iran, using the CE-QUAL-W2 model. The results showed that thermal stratification occurs in summer and the reservoir is almost completely mixed in terms of changes in dissolved oxygen in December. The concentration of dissolved oxygen in the water surface increases sharply in spring, which is due to the photosynthesis of algae in these months. The lowest dissolved oxygen concentration (0 mg/L) occurs in January and December and in the hypolimnion, while the highest concentration (10.2 mg/L) is observed at the water surface in May (Kiani Sadr 2017). Since the Yamchi dam reservoir, Ardabil, Iran, is used for drinking and agricultural purposes, it is necessary to investigate its qualitative parameters, the timing of thermal stratification, eutrophication, and their effect on the water dissolved oxygen concentration. Therefore, in this study, in order to identify the water quality status of Yamchi Dam, thermal stratification and dissolved oxygen concentration were simulated using the CE-QUAL-W2 model, and the eutrophication conditions of the dam reservoir have also been investigated which these evaluations are beneficial to ensure the safety of the water for not only drinking and agricultural purposes but also for the environment by controlling the phenomenons like eutrophication and thermal stratification affecting water quality parameters.
Material and methods
Study area
Constructed in 2005, the Yamchi dam (38°2’- 38°4’ N, 48°2’-48°5’ E) is located on Balkhlichai River ca. 25 km away from west of Ardabil (Fig. 1). Considering the altitude and geographical location of the reservoir, it is classified as a warm monomictic reservoir. The dam was constructed for drinking water supply and irrigation purposes with the capacity of 82 MCM: 80 MCM useful storage and 2 MCM dead storage.
CE-QUAL-W2 model
In this study, the CE-QUAL-W2 model was used to simulate the thermal stratification and its effects on dissolved oxygen concentration. This is a two-dimensional, longitudinal/vertical, hydrodynamic model to study water quality, and it is best suited for relatively long and narrow water bodies, such as rivers, lakes, reservoirs, estuaries, as well as entire river basins with multiple reservoirs and river segments, exhibiting longitudinal and vertical water quality gradients. Geometric data, initial conditions, boundary conditions, hydraulic parameters, kinetic parameters, and calibration data are required for the CE-QUAL-W2 model (Wells 2020a, b).
Governing equations of the CE-QUAL-W2 model
The CE-QUAL-W2 model solves the mean transverse equations using the finite difference method. These equations include momentum in the x-direction (Eq. 1), momentum in the z-direction (Eq. 2), continuity equation (Eq. 3), state equations (Eq. 4), and water surface elevation equation (Eq. 5)
where x and z are horizontal and vertical coordinates, B is the width of the waterbody, U is the horizontal mean transverse velocity, W is the vertical mean transverse velocity, ρ is water density, t is time, p is pressure, g is the gravitational acceleration, q is the inlet and outlet flow rate, α is the slope of waterbody bed, dz and dx are the thermal elements in x and z directions, τxx and τxz are turbulent shear stress in x and z directions, βη is water surface width that varies with time and location, η is the water surface elevation, and h is depth. In the state equation, the density is a function of water temperature (TW), total dissolved solids concentration (∅TDS), and suspended solids concentration (∅SS) (Wells 2020a, b).
Model calibration
Model calibration was performed in three steps, the calibration of reservoir geometry, the calibration of water surface elevation, and the calibration of temperature and quality (concentration of qualitative parameters). After calibrating the model, Absolute Mean Error (AME) (Eq. 6) and Root-Mean-Square error (RMSE) (Eq. 7) were used to measure the error between the observed and predicted data
where n is the total number of data and xpi and xoi are the predicted and observational data, respectively (Wells 2020a, b).
Simulation duration and geometry
The Yamchi dam reservoir was simulated for a one-year period from May 2015 to April 2016. The waterbody of the reservoir was divided into a primary branch with 28 longitudinal segments, each having a 200 m length. Reservoir depth was also divided into 32 elements with a 2 m depth. Figure 2 depicts a view of the geometrical model of the Yamchi dam reservoir.
Inflow temperature
Due to the lack of sufficient data on the temperature of inlet water to the reservoir and the existence of a significant relationship between this parameter and air temperature (Fig. 3), the temperature of the inlet to the reservoir was extracted using the Nir synoptic station data for the simulation period. In this research, the existing inlet water temperatures and the meteorological data were obtained from Iran Water Resources Management Company and Iran Meteorological Organization.
Eutrophication
Eutrophication is the process in which a water body becomes overly enriched with nutrients like Nitrogen and Phosphorus, leading to dramatic growth of algae and simple plant life which leads to the deterioration of water quality and the depletion of dissolved oxygen in water bodies which threaten the survival of organisms (Sun et al. 2022 and Olivera et al. 2020).
Vollenweider trophic graph
Vollenweider provided the graph shown in Fig. 4 to diagnose eutrophication in dam reservoirs. In this diagram, H is the average depth of the reservoir (m), TW is the water retention time in the reservoir (year), and LP is the amount of entrance of phosphorus into the dam reservoir, which is obtained by dividing the amount of input phosphorus in the reservoir per year by lake area (Parchami et al. 2016).
Carlson trophic state index
Carlson trophic state index (TSI) uses three water quality parameters, namely, Secchi depth (SD), chlorophyll-a (CHL), and total phosphorous (TP), to determine the eutrophication level of the dam reservoirs.
In using this index, it should be noted that these three water quality parameters can vary from one reservoir to another and from one season to another. TSI (SD) might be associated with the error, as opacity might not be due to the presence of algae alone, and the TSI (CHL) can be more reliable overall. Therefore, the TSI (CHL) was used in this study. Table 1 shows the eutrophication level of dam reservoirs according to Carlson TSI (Vice Presidency for Strategic Planning and Supervision 2011).
Results and discussion
Model calibration
For geometric calibration of the reservoir, according to the observational and simulated data of volume-area-elevation, the observational volume and area were compared with predicted data by the model at various elevations. To do this, the observational and simulated data were refined by changing the width of the segments. Figures 5 and 6 show these comparisons. As can be seen, there is a good agreement between observational and simulation data. The second step was to calibrate the water surface elevation. The simulated water surface elevation during the simulation period should be similar to the observed data. A program (waterbal-ivf37.exe) was used to calibrate the water surface elevation. Figure 7 depicts a comparison of observational and simulated data, while Table 2 shows the error calculated by the program. According to the results of other researches including Talakesh et al. 2019 with the calculated AME and RMSE of 0.74 and 0.84, respectively, calibration has been appropriately conducted in this research (Talakesh et al. 2019). The third step was the calibration of temperature and quality. According to the comparison of observational data and the simulation results of the model, the trend of changes in temperature and dissolved oxygen parameters has been simulated with acceptable performance (Tables 3 and 4). According to the results conducted in other researches shown in the user manual of the CE-QUAL-W2 model, calibration has been done properly. Furthermore, as can be seen, during the validation process for temperature parameter, the AME calculated for two months were higher than one which led to a higher amount for AME calculated for validation period. This could be due to human Error or not calibrated devices (Table3).
Thermal stratification
Thermal stratification, refers to the uneven variation of water temperature in vertical profiles of a water body (in our case Yamchi Dam Reservoir). In a stratified reservoir three layers are formed: an upper layer called (Epilimnion), which is well-mixed and a bottom layer called (hypolimnion), which is disconnected from the former layer by a third layer called thermocline (Yuanning et al. 2022; Yigzaw et al. 2019).
The effects of the thermal stratification of reservoirs on changes in dissolved oxygen concentration are undeniable (Yuanning et al. 2022). The Yamchi dam reservoir has a four-month stratification period, starting in June and reaching its peak in August, resulting in a temperature difference of up to 6 °C between the epilimnion and hypolimnion. It is possible to observe more temperature differences if the depth of stored water exceeds its value during the simulated period in this study. With the beginning of September and the decrease in air temperature, the temperature difference between the epilimnion and hypolimnion decreases to the point that the mixing process begins in mid-September, and complete mixing is observed in the coming months of autumn and winter due to decreasing the temperature of the reservoir water. The reservoir temperature varies between 0 and 2 °C in January and February. Also, the mixing process continues in April and May, and the epilimnion begins to form in early June, and the reservoir enters the period of thermal stratification.
Dissolved oxygen concentration
The importance of monitoring the Dissolved oxygen concentration in water bodies is inevitable as this parameter is vital to support aquatic life. In this regard, the distribution of the dissolved oxygen in Yamchi dam has been modeled (Kiani Sadr 2017). Figures 8, 9, 10 and 11 show the dissolved oxygen concentration in the simulation period in the Yamchi dam reservoir. According to these figures, from mid-October to May, the reservoir becomes fully mixed in terms of changes in dissolved oxygen concentration. From September, with the decrease in water temperature, as it is predicted, the concentration of dissolved oxygen starts to increase so that the concentration reaches its maximum amount (more than 12 mg/L) in January and February. However, with the onset of temperature increase which leads to less gas being soluble in the water body from March to June, when the reservoir is still in the mixing condition, the dissolved oxygen concentration decreases to about 9 mg/L. In the following months, with the beginning of the thermal stratification period in summer and its intensification in July and August, the amount of dissolved oxygen starts to decrease dramatically, Specifically in the hypolimnion the amount of DO becomes equal to 0 mg/L, which is due to high presence of nutrients and eutrophic condition of the Yamchi dam reservoir leading to the high oxygen consumption in this layer. During this period, the reduction in oxygen dissolution causes the anaerobic decomposition of some compounds in water, resulting in an unpleasant odor, color, and taste.
Vollenweider graph
According to the graph and method provided by Vollenweider, in the Yamchi dam reservoir, the value of H/Tw, which is equal to the Q/A ratio, is equal to:
The average annual flow rate to the Yamchi dam reservoir is 64.9 MCM and the total phosphorus concentration entering the Yamchi dam reservoir is 0.33 mg/L. Therefore, the amount of phosphorus entering the reservoir per year in terms of grams is equal to:
The resulting LP is equal to:
According to the Vollenweider graph (Fig. 12), the condition of the Yamchi dam reservoir is in the eutrophic zone.
Carlson trophic state index
The average values of TSI (chl) in the reservoir in the four seasons of spring, summer, autumn, and winter are 47.97, 46.07, 42.02, and 44.06, respectively. As a result, according to the calculations and Table 1, the Yamchi dam reservoir is in the eutrophic condition in spring and summer and in the mesotrophic condition in winter and autumn.
Conclusion
In this study, thermal stratification, eutrophication, and dissolved oxygen concentration in the Yamchi dam reservoir have been studied using the CE-QUAL-W2 two-dimensional hydrodynamic model for a one-year period (2015–2016). Due to the importance of the study reservoir in supplying the drinking and agricultural water in the region, the necessity of this study was apparent. The results show a four-month period of thermal stratification, beginning in June and reaching its peak in August. A temperature difference of about 6 °C is observed between the epilimnion and hypolimnion in the vicinity of the dam axis. This stratification continues until the middle of September, and the reservoir is witnessing a mixing process in other months. Therefore, the Yamchi dam reservoir has a thermal stratification of summer type and experiences a mixing in autumn and winter seasons. The eutrophication was investigated according to the amount of total phosphorus entering the reservoir and chlorophyll-a concentration using Carlson TSI and Vollenweider graph, which according to the results, the reservoir is in eutrophic and mesotrophic conditions. Also, although the dissolved oxygen concentration in the epilimnion during the whole simulation period is more than 6 mg/L, in the lower layers, its concentration has decreased sharply from June to September and even decreased to nearly 0 mg/L. After summer, with decreasing temperature and the beginning of mixing, the concentration of dissolved oxygen increases and reaches more than 11 mg/L in winter.
Data availability
Data used in this research were obtained from Iran Water Resources Management Company and Iran Meteorological Organisation; therefore the data are not available to share.
References
Beiramipoor S, Qaderi K, Haghjuie, Rahimpoor M (2018). Reservoir water quality management of Baft dam through selected drainage from the dam outlet locations using the model CE-QUAL-W2. Irrigation & Water Engineering. 8(31), pp. 237. https://www.magiran.com/paper/1858525https://www.researchgate.net/publication/355789003_Reservoir_water_quality_management_of_Baft_dam_through_selected_drainage_from_the_dam_outlet_locations_using_the_model_CE-QUAL-W2 (In Persian).
Chai B, Li Y, Huang T, Zhao X (2014) Pollution characteristics of thermally-stratified reservoir: A case study of the Heihe reservoir in Xian city China. J Chem Pharm Res USA 6(7):1231–1240
de Oliveira TF, de Sousa Brandao IL, Mannaerts CM, Hauser-Davis RA, de Ferreira Oliveira AA, Fonseca Saraiva AC, de Oliveira MA, Ishihara JH (2020) Using hydrodynamic and water quality variables to assess eutrophication in a tropical hydroelectric reservoir. J Environ Manage 256(1):11. https://doi.org/10.1016/j.jenvman.2019.109932
Ebrahimi M, Jabbari E, Abbasi H (2015) Simulation of thermal stratification and salinity in dam reservoir using CE-QUAL-W2 software (case study: Abaft dam). J Civil Engine Urban 5(1):07–11
Kaveh M, Moridi A, Shoorian M (2018) Solutions for improving water quality in dams’ reservoirs (Case Study: Ilam Reservoir). Water Eng 11(37):87–97 ((In Persian))
Khonok A, Sarai Tabrizi M, Babazadeh H, Saremi A, Mohammadi Ghaleni M (2021) Sensitivity analysis of water quality parameters related to flow changes in regulated rivers. Int J Environ Sci Technol 19:3001–3014. https://doi.org/10.1007/s13762-021-03421-z
Kiani S (2017) Simulation of thermal stratification and concentration of the solvent oxygen using model CE QUAL W2 (Case Study: GARSHA Dam). J Wetland Ecobiol 9(2):39–52 ((In Persian))
Ma S, Kassinos SC, Fatta-Kassinos D, Akylas E (2008) Effects of selective withdrawal schemes on thermal stratification in kouris dam in Cyprus. Lakes & Reservoirs: J Res Manage 13:51–61. https://doi.org/10.1111/j.1440-1770.2007.00353.x
Mercy G, Kioko N (2021) Assessment of water quality in selected dams in Machakos municipality. Kenya Environ Earth Sci 11(10):35–42. https://doi.org/10.7176/JEES/11-10-04
Parchami N, Mohammadnejad BA, Behmanesh J (2016) Investigation of water quality in Mahabad dam reservoir using novotny index and Vollenweider graph. J Water Soil Sci 25(4):243–257 ((In Persian))
Rahimi Movaghar M, Mirbagheri S, Kerachian R (2019) Total dissolved solid and dissolved oxygen modeling, thermocline calculation and applying reservoir salinity reduction scenario in Shahid Rajaee reservoir using CE-QUAL-W2. Water Supply 19(2):424–433. https://doi.org/10.2166/ws.2018.087
Rezaei Barandagh H, Salmasi F, Sahebi F (2018) Water quality and temperature stratification of Zanjan Taham Dam with CE-QUAL-W2 software. Water Soil Conserv 25(1):127–145. https://doi.org/10.22069/jwsc.2018.13327.2799 ((In Persian))
Sabeti R, Jamali S, Hajikandi Jamali H (2017) Simulation of thermal stratification and salinity using the Ce-Qual-W2 Model (case study: Mamloo dam). Eng Technol Appl Sci Res 7(3):1664–1669. https://doi.org/10.48084/etasr.1062
Salehi M, Khanitemeliyeh Z, Parchami N, Ahmadpour Z (2019) Numerical modeling of thermal stratification and water quality in reservoir by CE-QUAL-W2 model. Water Soil Conserv 26(4):53–73. https://doi.org/10.22069/jwsc.2019.14971.3010 ((In Persian))
Shaban E, Ketabchi H (2019) Simulation of sulfur cycle using CE-QUAL-W2 model (case Study of Seymareh dam reservoir, Iran). Iran Water Res J 13(33):151–161 ((In Persian))
Shabani N, Rahmanifiroozjaee A, Abessi O (2019) Thermal stratification of Seymareh Dam using two-dimensional, hydrodynamic and water quality model: CE-QUAL-W2. J Environ Sci Technol 21(7):77–87. https://doi.org/10.22034/JEST.2018.22904.3200 ((In Persian))
Sun W, Niu X, Teng H, Ma Y, Ma L, Liu Y (2022) A 133-year record of eutrophication in the Chaihe Reservoir. Southwest China J Ecol Indic 134:1–10. https://doi.org/10.1016/j.ecolind.2021.108469
Talakesh S, Fatahi Nafechi R, Samadi Boroujeni H, Mirabbasi Najafabadi R, Khajepour I (2019) Investigation on stratification of temperature and dissolved oxygen in a large dam reservoir (case study: Karun 3 Dam). Iran Water Res J 13(32):49–57 ((In Persian))
Vice Presidency for Strategic Planning and Supervision. (2011). Guidelines for water quality studies of large dam reservoirs. Technical note No. 550. Publications of technical and executive system of Iran. https://ehss.moe.gov.ir/ (In Persian)
Wells, S. A. (2020a). CE-QUAL-W2: A two-dimensional, laterally averaged, hydrodynamic and water quality model, version 4.2.2, user manual part 2, hydrodynamic and water quality model theory," Department of Civil and Environmental Engineering, Portland State University, Portland, OR.
Wells, S. A. (2020b). CE-QUAL-W2: A two-dimensional, laterally averaged, hydrodynamic and water quality model, version 4.2.2, user manual part 4, model examples. Department of Civil and Environmental Engineering, Portland State University, Portland, OR.
Yigzaw W, Li H-Y, Fang X, Leung LR, Voisin N, Hejazi MI, Demissie Y (2019) A multilayer reservoir thermal stratification module for earth system models. J Adv Model Earth Syst 11:3265–3283. https://doi.org/10.1029/2019MS001632
Yuanning Z, Xueping G, Bowen S, Chang L, Budong L, Xiaobo L, (2022). Tracking thermal structure evolution: An objective practice in a stratified reservoir based on high-frequency measurements’, J Hydrol: Reg Stud, 39:100989, ISSN 2214-5818, https://doi.org/10.1016/j.ejrh.2022.100989
Acknowledgements
This research is extracted from the thesis of the master's student (Mr. Amin Esmaeilzadeh Hanjani) in Water Science and Engineering, Islamic Azad University of science and Research Branch.
Funding
Funding information is not applicable. No funding was received. “The author(s) received no specific funding for this work.”
Author information
Authors and Affiliations
Contributions
All authors had equal contribution in writing, review, and final approval of the paper.
Corresponding author
Ethics declarations
Conflict of interest
The author declares that there is no conflict of interest.
Ethical approval
The present study and ethical aspect was approved by Department of Water Engineering and Sciences, Faculty of Agricultural Sciences and Food Industries, Science and Research Branch, Islamic Azad University (SRBIAU), Tehran, Iran.
Consent to participate
All authors designed the study, collected data, wrote the manuscript and revised it.
Consent to publish
All authors agree to publish this manuscript. There is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Hanjaniamin, A.E., Tabrizi, M.S. & Babazadeh, H. Dissolved oxygen concentration and eutrophication evaluation in Yamchi dam reservoir, Ardabil, Iran. Appl Water Sci 13, 9 (2023). https://doi.org/10.1007/s13201-022-01786-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s13201-022-01786-1