Abstract
In the present work natural rubber (NR) latex and starch was added as an adhesive to synthesize the medium density fiber (MDF) board panels. The studies are aimed on increasing the mechanical and physical properties of MDF by using NR latex and starch as an adhesive. Three combinations which are 5 g of starch with 15 g of NR latex, 10 g starch with 10 g of NR latex and 15 g of starch with 5 g of NR latex were prepared and the results obtained were compared with the MDF prepared by using urea formaldehyde adhesive. Adhesive preparation trials, physico-chemical testing of adhesives and mechanical testing of adhesives bonded to MDF were done. The morphology of the specimens was characterized by using thermo gravimetric analysis (TGA) and fourier transform infrared spectroscopy. The mechanical testing results of MDF obtained from adhesive prepared using 5 g starch with 15 g NR latex shows higher mechanical strength in comparison to two other formulations. From the TGA graph, it was observed that the thermal stability of the MDF boards having higher starch percentage is higher in comparison to others. The results of this study indicated that starch can be used as a viable alternative binder with NR latex.
Similar content being viewed by others
References
Abilash N, Sivapragash M (2013) Environmental benefits of eco-friendly natural fiber reinforced polymeric composite materials. Int J Appl Innov Eng Manag (IJAIEM) 2:53–59
Honeycutt T, Swanson M, Doyle W, Clark M, Culp R (2011) Vytex natural rubber latex: a proposed industry standard for the manufacture of commercial natural rubber products. Vystar Corp. http://www.vytex.com/BizDocs/Vytex_Ind_Standard.pdf
Irle M, Barbu MC (2010) Wood-based panel technology. In: Heiko T (ed) Wood based panels: an introduction for specialists. Brunel university press, London, p 190
Kiatkamjornwong S, Surunchanajirasakul P, Tasakorn P (2001) Natural rubber–cassava starch foam by compression moulding. Plast, Rubber Compos 30:318–327
Natural rubber statistics (2013) online. http://www.lgm.gov.my/nrstat/nrstats.pdf
Naya M, Nakanishi J (2005) Risk assessment of formaldehyde for the general population in Japan. Regul Toxicol Pharmacol 43(3):232–248
Osemeahon SA, Barminas JT (2007) Study of some physical properties of urea formaldehyde and urea proparaldehyde copolymer composite for emulsion paint formulation. Int J Phys Sci 2(7):169–177
Roumeli E, Papadopoulou E, Pavlidou E, Vourlias G, Bikiaris D, Paraskevopoulos KM, Chrissafis K (2012) Synthesis, characterization and thermal analysis of urea-formaldehyde/nanoSiO2 resins. Thermochim Acta 527:33–39
Shey J, Imam SH, Glenn GM, Orts WJ (2006) Properties of baked starch foam with natural rubber latex. Ind Crops Prod 24:34–40
Yuhazri YM, Sihombing H, Jeefferie AR, Mujahid AZA, Balamurugan AG, Norazman MN, Norazman A (2011) Optimization of coconut fibers toward heat insulator applications. Glob Eng Technol Rev 1(1):35–40
Acknowledgments
The author is thankful to University Malaysia Pahang for providing post graduate scholarship and funding to complete this research.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Akbari, S., Gupta, A., Khan, T.A. et al. Synthesis and characterization of medium density fiber board by using mixture of natural rubber latex and starch as an adhesive. J Indian Acad Wood Sci 11, 109–115 (2014). https://doi.org/10.1007/s13196-014-0124-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13196-014-0124-0