Abstract
Austempered ductile irons (ADI) have been developed for an increasing number of the engineering applications such as crankshaft, gears, and other mechanic equipments because of its combination of strength and toughness. Therefore, austempering process has important effects on the mechanical properties of ADI. In this study, we have investigated the effect of austempering process on the cutting tool stresses. The cutting forces (main cutting force, feed force and thrust force) obtained from experimental studies have been applied to rake face, main cutting edge, auxiliary cutting edge on the cutting tool, and then the stresses (von-Mises, shear stress, normal stresses in the X, Y and Z directions) occurred on the cutting tool has been analyzed based on finite element method using ANSYS Workbench commercial software. It is also observed that analytical process of Frocht for the stresses on cutting tool tip. The results obtained show that the austempering process is the significant factor affecting cutting tool stresses.
Similar content being viewed by others
References
Ghani A K, Choudhury I A, Husni, J Mater Process Technol 127 (2002) 17.
Masuda M, Sato T, Kori T, and Chujo Y, Wear 174 (1994) 147.
Aslantas K, Ucun I, and Gok K, J Manuf Sci Eng 130 (2008) 054503.
Seker U, and Hasirci H, J. Mater. Process., 173 (2006) 260.
Attanasio A, Ceretti E, Rizzuti S, Umbrello D, and Micari F, CIRP Manuf Technol 57 (2008) 61.
Köse E, Kurt A, and Şeker U, J Mater Process Technol 196 (2008) 165.
Kim K W, Lee W Y, and Sin H C, J Mater Process Technol 86 (1999) 45.
Duran A, and Nalbant M, Mater Des 26 (2005) 549.
Jaharah A G, Wahid S W, Che Hassan C H, Nuawi M Z and Mohd Nizam A R, J Sci Res 2 (2009) 271.
Dechjarern S, Int J Sci Technol Produc Manuf 1 (2008) 149–158.
Yanda H, Jaharah A G, and Che Hassan C H, Eng e-Trans 4 (2009) 7.
Bareggi A, Donnell O, and Torrance A, in Paper Present at the Proceedings of the 24th International Manufacturing Conference Modelling Thermal Effects in Machining by Finite Element Methods, Waterford, (2007), p 263.
Ucun I, and Aslantaş K, Int J Adv Manuf Technol 54 (2011) 899.
Patrascu G, and Carutasu G, Fasc Manag Technol Eng, 6 (2007) 1423.
Zhou J M, Walter H, Andersson M and Stahl J E, Int J Mach T Manuf, 43 (2003) 301.
Ozel T, Int J Mach Tools Manuf 46 (2006) 518.
Gürbüz H, Kurt A, Ciftci İ, and Seker U, Strojniški vestnik J Mech Eng 572 (2011) 91.
Mondal B, Chattopadhyay A B, Virkar A, and Paul A, Wear 156 (1992) 365.
Mondal B, Adv Appl Ceram, 104 (2005) 256.
Mandal N, Doloi B, and Mondal B, Int J Precis Eng Manuf, 13 (2012) 1589.
Devillez A, Schneider F, Dominiak S, Dudzinski D and Larrouquere D, Wear, 262 (2007) 931.
Ciftci I, Tribol Int 39 (2006) 565.
Ucun I, Aslantas K, Tasgetiren S, and Gok K, J Fac Eng Arch Gazi Univ, 22 (2007) 739.
Frocht MM, Photoelasticity, Wiley, I & II (1948).
Zorev NN, Int Res Produc Eng, (1963), 42.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Gok, A., Gok, K. The Effect on the Cemented Carbide Cutting Tool of Austempering Process. Trans Indian Inst Met 67, 667–674 (2014). https://doi.org/10.1007/s12666-014-0389-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12666-014-0389-4