Abstract
In wafer probing, probe needles provide the physical contact between the wafers and the probe card. During the contact process, the shape of the probe needle and the mounting configuration onto the probe card has large influences on the stresses and contact force that the probe needles experience. In this paper, static performance of a vertical-type probe needle integrated with floating mount technology was analyzed with a nonlinear finite element analysis. The geometry of a vertical probe needle was optimized in order to minimize the stress that occurs during the overdrive process, while maintaining adequate force for proper contact with the wafer. Maximum stress and contact force were formulated using the coefficients of 4th order polynomial representing the shape of cobra body, and then curvature of the probe needle body was optimized by applying the constrained minimization function to these functions. The maximum stress in the vertical probe pin at 125 μm overdrive was reduced from 972 MPa to 666 MPa by employing the probe needle with optimized geometry. The optimized design also induced the contact force of 5.217 gf, which is in the range of the required contact force of 5 to 8 gf.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Sasho, S. and Sakata, T., “Four Multi Probing Test for 16 Bit Dac with Vertical Contact Probe Card,” Proc. of International Test Conference, pp. 86–91, 1996.
Chang, H. Y., Pan, W. F., and Lin, S. M., “Investigation of Contact Behavior and Design of Vertical Probe for Wafer Level Probing,” IEEE Transactions on Components, Packaging and Manufacturing Technology, Vol. 2, No. 4, pp. 710–718, 2012.
Chiu, J. T. and Chang, D. Y., “A New Probe Design Combining Finite Element Method and Optimization used for Vertical Probe Card in Wafer Probing,” Precision Engineering, Vol. 33, No. 4, pp. 395–401, 2009.
Hauck, T. and Muller, W., “Large Deformation of Beam Columns-a Closed Form Solution and Design Guide for Vertical Buckling Probe Needles,” Proc. of 11th International Conference on Thermal, Mechanical & Multi-Physics Simulation, and Experiments in Microelectronics and Microsystems, pp. 1–3, 2010.
Hauck, T., Müller, W. H., and Schmadlak, I., “Nonlinear Buckling Analysis of Vertical Wafer Probe Technology,” Microsystem Technologies, Vol. 16, No. 11, pp. 1909–1920, 2010.
Iwai, H., Nakayama, A., Itoga, N., and Omata, K., “Cantilever Type Probe Card for At-Speed Memory Test on Wafer,” Proc. of 23rd IEEE VLSI Test Symposium, 85–89, 2005.
Comeau, A. R. and Nadeau, N., “Modeling the Bending of Probes used in Semiconductor Industry,” IEEE Transactions on Semiconductor Manufacturing, Vol. 4, No. 2, pp. 122–127, 1991.
Takahiro, I., Sawada, R., and Higurashi, E., “Fabrication of Micro IC Probe for LSI Testing,” Sensors and Actuators A: Physical, Vol. 80, No. 2, pp. 126–131, 2000.
Lee, K. and Kim, B., “Mems Spring Probe for Non-Destructive Wafer Level Chip Test,” Journal of Micromechanics and Microengineering, Vol. 15, No. 5, pp. 953, 2005.
Taber Jr, F. L., “An Introduction to Area Array Probing,” Proc. of 8th IEEE International Test Conference, pp. 277–277, 1998.
Beiley, M., Leung, J., and Wong, S. S., “A Micromachined Array Probe Card-Fabrication Process,” IEEE Transactions on Components, Packaging, and Manufacturing Technology, Part B: Advanced Packaging, Vol. 18, No. 1, pp. 179–183, 1995.
Zimmermann, K. F., “Siprobe-a New Technology for Wafer Probing,” Proc. of the 5th IEEE SouthWest Test Conference, pp. 106–112, 1995.
Pardee, B. and Fulton, B., “Using MLO Packages to Build Vertical Probe Space Transformers,” Proc. of 12th IEEE SouthWest Test Workshop, pp. 1–25, 2002.
Byrnes, H. P. and Wahl, R., “Contact for an Electrical Contactor Assembly,” US Patent, No. 4027935 A, 1977.
Maekawa, S., Takemoto, M., Kashiba, Y., Deguchi, Y., Miki, K., and Nagata, T., “Highly Reliable Probe Card for Wafer Testing,” Proc. of 50th IEEE Electronic Components & Technology Conference, pp. 1152–1156, 2000.
Chao, Y. C., Lee, Y. J., Liu, J., Shen, G. S., Tsai, F. J., et al., “Development of Probing Mark Analysis Model [IC Testing],” Proc. of 5th International Conference on in Electronic Packaging Technology Proceedings, pp. 40–43, 2003.
Broz, J. J. and Rincon, R. M., “Probe Contact Resistance Variations during Elevated Temperature Wafer Test,” Proc. of IEEE International Test Conference, pp. 396–405, 1999.
Doherty, D. and Rogers, R., “Vertical Probe Alternative for Cantilever Pad Probing,” IEEE SW Semiconductor Wafer Test Workshop, 2008.
Wakuda, M., Yamauchi, Y., Kanzaki, S., and Yasuda, Y., “Effect of Surface Texturing on Friction Reduction between Ceramic and Steel Materials under Lubricated Sliding Contact,” Wear, Vol. 254, No. 3, pp. 356–363, 2003.
Kataoka, K., Kawamura, S., Itoh, T., Suga, T., Ishikawa, K., and Honma, H., “Low Contact-Force and Compliant Mems Probe Card Utilizing Fritting Contact,” Proc. of 15th IEEE International Conference on Micro Electro Mechanical Systems, pp. 364–367, 2002.
Bates, R. D., “The Search for the Universal Probe Card Solution,” Proc. of IEEE International Test Conference (ITC), pp. 533–533, 1997.
Weeden, O., “Probe Card Tutorial,” Keithley Instruments, Inc, pp. 1–40, 2003.
Brizmer, V., Kligerman, Y., and Etsion, I., “The Effect of Contact Conditions and Material Properties on the Elasticity Terminus of a Spherical Contact,” International Journal of Solids and Structures, Vol. 43, No. 18, pp. 5736–5749, 2006.
Tunaboylu, B., “Testing of Copper Pillar Bumps for Wafer Sort,” IEEE Transactions on Components, Packaging and Manufacturing Technology, Vol. 2, No. 6, pp. 985–993, 2012.
Dowling, N. E., “Mechanical Behavior of Materials,” Prentice Hall, pp. 413–415, 2007.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Kwon, HJ., Lee, J., Shin, B. et al. Geometry design of vertical probe needle using mechanical testing and finite element analysis. Int. J. Precis. Eng. Manuf. 15, 2335–2342 (2014). https://doi.org/10.1007/s12541-014-0598-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12541-014-0598-0