Abstract
The distribution of damage in deep rock cores is critical for assessing its influence on rock mechanical characteristics. This paper presents a case study on estimating the coring damage extent induced by the stress redistribution through a combined method of numerical simulation and X-ray Computed Tomography (CT) scanning. Rock cores are taken at 1900 m depth from the test tunnel at Jin-ping Second Stage Hydropower Station (JPII) in China. Firstly, the stress path experienced by the rock core during coring has been examined by the numerical simulation, and the distribution of tensile zone in the cross-section of rock core is also discussed. Then two kinds of samples, collected from the same position under different stress levels, are scanned to obtain CT images, and a special CT value analysis strategy was adopted to evaluate coring damage intensities of these samples. The result indicates that the stress state can be regarded as the principal factor for the distribution of coring damage. During coring in the Test Tunnel of JPII under the quasi-hydrostatic stress condition, high tensile stresses (over 5 MPa) are observed at the exterior edge of rock cores, which may lead to the nucleation of microcracks around the core boundary, and the coring damage then propagates to the core centre. The CT scanning also illustrates that the coring damage zone may cover approximately 70~80% of the entire cross-section from the outside inside (stress level of 50 MPa), and that the central part of the core is less damaged or eventually undisturbed. Thus, intact rock samples can be expected to be obtained by overcoring the original rock cores. However, the applicability of the overcoring method seems to be largely dependent on the state of in-situ stress at the coring site. The whole core may be damaged if the lateral stress coefficient reaches a critical value (e.g. greater than 3.0), in which case a special coring equipment should be adopted to improve the stress state during coring.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Chu W. J. (2009). Wall rock stabilization and safety evaluation of deep buried tunnel, Hangzhou: Hydro-China Hua-dong Engineering Corporation (in Chinese).
Durelli, A. J., Obert, L., and Parks, V. J. (1968). “Stress required to initiate core discing.” Transaction Society of Mining Engineers, Vol. 241, pp. 269–276.
Eberhardt, E., Stead, D., and Stimpson, B. (1999). “Effects of sample disturbance on the stress-induced microfracturing characteristics of brittle rock.” Canadian Geotechnical Journal, Vol. 36, No. 2, pp. 239–250, DOI: 10.1139/t98-109.
Fairhurst, C. (2003). Rock Mechanics and Radioactive Waste Isolation-“One small step for geology, one giant leap for rock mechanics”. Fourth Müller Lecture, Tenth Congress of the International Society for Rock Mechanics, Sandton, South Africa, September 8-12.
Feng, X. T., Chen, S. L., and Zhou, H. (2004). “Real-timE Computerized Tomography (CT) experiments on sandstone damage evolution during triaxial compression with chemical corrosion.” International Journal of Rock Mechanics and Mining Sciences, Vol. 41, No. 2, pp. 181–192, DOI: 10.1016/S1365-1609(03)00059-5.
He, M. C., Xie, H. P., Peng, S. P., and Jiang, Y. D. (2005). “Study of rock mechanics in deep mining engineering.” Chinese Journal of RockMechanics and Engineering, Vol. 24, No. 16, pp. 2803–2813, DOI: 1000-6915(2005)16-2803-11 (in Chinese).
Holt, R. M., Brignoli, M., and Kenter, C. J. (2000). “Core quality: quantification of coring-induced rock alteration.” International Journal of Rock Mechanics and Mining Sciences, Vol. 37, No. 6, pp. 889–907, DOI: 10.1016/S1365-1609(00) 00009-5.
Jaeger, J. C. and Cook, N. G. W. (1963). “Pinching off and disking of rock.” Journal of Geophysical Research, Vol. 68, No. 6, pp. 1759–1765, DOI: 10.1029/JZ068i006p01759.
Kaga, N., Matsuki, K., and Sakaguchi, K. (2003). “The in situ stress states associated with core discing estimated by analysis of principal tensile stress.” International Journal of Rock Mechanics and Mining Sciences, Vol. 40, No. 5, pp. 653–665, DOI: 10.1016/S1365-1609 (03)00057-1.
Kawakata, H., Cho, A., Kiyama, T., Yanagidani, T., Kusunose, K., and Shimada, M. (1999). “Three-dimensional observations of faulting process in Westerly granite under uniaxial and triaxial conditions by X-ray CT scan.” Tectonophysics, Vol. 313, No. 3, pp. 293–305, DOI: 10.1016/S0040-1951(99)00205-X.
Li, Y. and Schmitt, D. R. (1998). “Drilling-induced core fractures and in situ stress.” Journal of Geophysical Research: Solid Earth (1978-2012), Vol. 103, No. B3, pp. 5225–5239, DOI: 0148-0227/98/97jb-02333$09.00.
Lim, S. S. and Martin, C. D. (2010). “Core discing and its relationship with stress magnitude for Lac du Bonnet granite.” International Journal of Rock Mechanics and Mining Sciences, Vol. 47, No. 2, pp. 254–264, DOI: 10.1016/ j.ijrmms. 2009.11.007.
Lockner, D. A., Byerlee, J. D., Kuksenko, V., Ponomarev, A., and Sidorin A. (1992). “Observations of quasistatic fault growth from acoustic emissions.” International Geophysics, Vol. 51, pp. 3–31, DOI: 10.1016/S0074-6142(08)62813-2.
Martin, C. D. and Stimpson, B. (1994). “The effect of sample disturbance on laboratory properties of Lac du Bonnet granite.” Canadian Geotechnical Journal, Vol. 31, No. 5, pp. 692–702, DOI: 10.1139/ t94-081.
Maury V. M. Santarelli F. J. and Henry J. P. 1990. “Corediscing A review.” In: Proceedings of 1st regional ISRM symposium for Africa Rock mechanicsin Africa: Swaziland South African National Groupon Rock Mechanics, Vol. 27, No. 2, pp. 221–231.
Obert, L. and Stephenson, D. E. (1965). “Stress conditions under which core discing occurs.” Society of Mining Engineers of AIME Transactions, Vol. 232, No. 3, pp. 227–235.
Sakaguchi, K., Lino, W., and Matsuki, K. (2002). “Damage in a rock core caused by induced tensile stress and its relation to differential strain curve analysis.” International Journal of Rock Mechanics and Mining Sciences, Vol. 39, No. 3, pp. 367–380, DOI: 10.1016/S1365-1609(02)00039-4.
Shan, Z. G., Wu, X. M., Yan, P., Liu, N., Zhu, Y. S., and Zhu, H. C. (2010). “Behavior of marble at Jinping II Project—part 1: intactrock.” In: Proceedings of the 44th US Rock Mechanics Symposium, the American Rock Mechanics Association, Salt Lake City, Utah, pp. 72.
Shimada, M. and Cho, A. (1990). “Two types of brittle fracture of silicate rocks under confining pressure and their implications in the earth’s crust.” Tectonophysics, Vol. 175, No. 1, pp. 221–235, DOI: 10.1016/ 0040-1951(90)90139-Y.
Song, I. and Haimson, B. C. (1999). “Core disking in Westerly granite and its potential use for in situ stress estimation. In: Amadei B, Kranz RL, Scott GA, Smeallie PH, editors.” Proceedings of 37st U.S. rock mechanics symposium, Colorado, Vol. 2. Rotterdam: A.A. Balkema, pp. 1173–80.
Stacey, T. R. (1982). “Contribution to the mechanism of core discing.” Journal of the South African Institute of Mining and Metallurgy, Vol. 82, pp. 269–275.
Wang, M. Y., Zhou, Z. P., and Qian, Q. H. (2006). “Tectonic deformation and failure problems of deep rock mass.” Chinese Journal of Rock Mechanics and Engineering, Vol. 25, No. 3, pp. 448–455, DOI: 1000-6915(2006)03-0448-08 (in Chinese).
Withjack, E. M. (1988). “Computerized Tomography for rock property determination and fluid flow visualization.” Society of Petroleum Engineers Formation Evaluation, Vol. 3, No. 4, pp. 696–704, DOI: 10.2118/16951-PA.
Yan, P., Lu, W. B., Chen, M., He, Y. L., Zhou, W., Chen, M., and Wang, G. H. (2012). “Damage-free coring technique for rock mass under high in-situ stresses.” Journal of Rock Mechanics and Geotechnical Engineering, Vol. 4, No. 1, pp. 44–53, DOI: 10.3724/SP.J.1235.2012. 00044.
Yan, P., Lu, W. B., He, Y., He, Y. L., Zhou, W., Chen, M., and Wang, G. H. (2016). “Coring damage mechanism of the Yan-tang group marble: Combined effect of stress redistribution and rock structure.” Bulletin of Engineering Geology and the Environment, Vol. 75, No. 4, pp. 1701–1716, DOI: 10.1007/s10064-015-0842-6.
Yang, G. S., Xie, D. Y., Zhang, C. Q., and Pu, Y. B. (1996). “CT identification of rock damage properties.” Chinese Journal of Rock Mechanics and Engineering, Vol. 15, No. 1, pp. 48–54 (in Chinese).
Zhao, X. D., Tang, C. A., Li, Y. H., Yuan, R. F., and Zhang, J. Y. (2006). “Study on the AE activity characters under uniaxial compression loading.” Chinese Journal of Rock Mechanics and Engineering, Vol. 25, No. Supp. 2, pp. 3673–3678, DOI: 1000-6915(2006)Supp2-3673-06 (in Chinese).
Zhou, H. M., Yang, Y., ZHANG, Y. H., Fan, L., and Zou, Y. Z. (2010). “Fine test on progressive fracturing of multi-crack rock samples under uiniaxial compression.” Chinese Journal of Rock Mechanics and Engineering, Vol. 29, No. 3, pp. 465–470, DOL: 1000-6915(2010) 03-0465-06 (in Chinese).
Zhou, H. W., Xie, H. P., and Zuo J. P. (2005). “Developments in researches on mechanical behaviour of rocks under the condition of high geostress in the depths.” Advances in Mechanics, Vol. 35, No. 1, pp. 91–99 (in Chinese).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Yan, P., He, Q., Lu, W. et al. Coring damage extent of rock cores retrieved from high in-situ stress condition: A case study. KSCE J Civ Eng 21, 2946–2957 (2017). https://doi.org/10.1007/s12205-017-1660-0
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12205-017-1660-0