Abstract
Many important processes—from the manufacturing of integrated circuit boards to an insect’s ability to walk on water—depend on the wetting of liquids on surfaces. Wetting is commonly controlled through material selection, coatings, and/or surface texture. However, wetting is sensitive to environmental conditions. In particular, some hydrophobic fluoropolymer coatings are sensitive to extended water exposure as evidenced by a declining contact angle and increasing contact angle hysteresis. Understanding “degradation” of these coatings is critical to applications that deploy them. The durability of a series of fluoropolymer coatings was tested by measuring the water contact angle before, during, and after extended submersion of coated glass slides in a deionized water bath. Vibration was introduced as a potential method for expediting the effects of long-term water exposure, so similar measurements were taken before, during, and after the same coatings were subject to ultrasonic vibration while covered in deionized water. Both methods caused changes in advancing and receding contact angles, but degradation rates of vibrated coatings were significantly increased. Prolonged soaking caused significant decreases in the contact angle of most of the samples, though most experienced significant recovery of hydrophobicity when heat-treated at 160°C after submersion. Some coatings appeared noticeably more resistant to degradation by one or both methods. FluoroSyl showed no clear change under submersion, while other coatings experienced significant contact angle change. Degradation of vibrated coatings was also inconsistent among coatings and was not simply an acceleration of the degradation resulting from submerging coatings in water. This was apparent as some coatings were affected by one method but not the other. Atomic force microscopy was utilized to characterize the surface roughness of the coatings and revealed differing surface effects for different coatings after submersion and heat treatment. However, the magnitude of this roughness change was insufficient to fully explain the wetting changes. The rate of contact angle degradation was not altered significantly for coatings that were vibrated with acceleration magnitudes between 700 and 7000 g.
Similar content being viewed by others
References
Asmatulu, R, Mahmud, GA, Hille, C, Misak, HE, “Effects of UV Degradation on Surface Hydrophobicity, Crack, and Thickness of MWCNT-Based Nanocomposite Coatings.” Prog. Org. Coat., 72 553–561 (2011)
Yang, XF, Tallman, DE, Bierwagen, GP, Croll, SG, Rohlik, S, “Blistering and Degradation of Polyurethane Coatings Under Different Accelerated Weathering Tests.” Polym. Degrad. Stab., 77 103–109 (2002)
Gutiérrez-Cano, V, Rodríguez, F, González, JA, Díaz, V, “Thermal Degradation of Hydrophobic Graphite-Based Thin Film Nano-Coatings Observed by Raman Spectroscopy.” Thin Solid Films, 648 8–11 (2018)
Han Yeong, Y, Steele, A, Loth, E, Bayer, I, De Combarieu, G, Lakeman, C, “Temperature and Humidity Effects on Superhydrophobicity of Nanocomposite Coatings.” Appl. Phys. Lett., 100 053112 (2012)
Mahadik, SA, Fernando, PD, Hegade, ND, Wagh, PB, Gupta, SC, “Durability and Restoring of Superhydrophobic Properties in Silica-Based Coatings.” J. Colloid Interface Sci., 405 262–268 (2013)
Ji, W-G, Hu, J-M, Zhang, J-Q, Cao, C-N, “Reducing the Water Absorption in Epoxy Coatings by Silane Monomer Incorporation.” Corros. Sci., 48 3731–3739 (2006)
Lacombre, CV, Bouvet, G, Trinh, D, Mallarino, S, Touzain, S, “Water Uptake in Free Films and Coatings Using the Brasher and Kingsbury Equation: A Possible Explanation of the Different Values Obtained by Electrochemical Impedance Spectroscopy and Gravimetry.” Electrochim. Acta, 231 162–170 (2017)
Zhou, Q, Wang, Y, “Comparisons of Clear Coating Degradation in NaCl Solution and Pure Water.” Prog. Org. Coat., 76 1674–1682 (2013)
Boinovich, L, Emelyanenko, AM, Pashinin, AS, “Analysis of Long-Term Durability of Superhydrophobic Properties Under Continuous Contact with Water.” ACS Appl. Mater. Interfaces, 2 1754–1758 (2010)
Zhou, Q, Wang, Y, Bierwagen, GP, “Flow Accelerated Degradation of Organic Clear Coat: The Effect of Fluid Shear.” Electrochim. Acta, 142 25–33 (2014)
Yuan, Z, Wang, X, Bin, J, Peng, C, Xing, S, Wang, M, et al., “A Novel Fabrication of a Superhydrophobic Surface with Highly Similar Hierarchical Structure of the Lotus Leaf on a Copper Sheet.” Appl. Surf. Sci., 285 205–210 (2013)
Youngblood, JP, Andruzzi, L, Ober, CK, Hexemer, A, Kramer, EJ, Callow, JA, et al., “Coatings Based on Side-Chain Ether-Linked Poly(ethylene glycol) and Fluorocarbon Polymers for the Control of Marine Biofouling.” Biofouling, 19 91–98 (2003)
Rao, AV, Latthe, SS, Mahadik, SA, Kappenstein, C, “Mechanically Stable and Corrosion Resistant Superhydrophobic Sol–Gel Coatings on Copper Substrate.” Appl. Surf. Sci., 257 5772–5776 (2011)
Liu, Y, Lin, Z, Moon, K, Wong, CP, “Superhydrophobic Nanocomposite Coating for Reliability Improvement of Microelectronics.” IEEE Trans. Compon. Packag. Manuf. Technol., 3 1079–1083 (2013)
Arunkumar, P, Kim, YH, Kim, HJ, Unithrattil, S, Im, WB, “Hydrophobic Organic Skin as a Protective Shield for Moisture-Sensitive Phosphor-Based Optoelectronic Devices.” ACS Appl. Mater. Interfaces, 9 7232–7240 (2017)
Lu, HW, Glasner, K, Bertozzi, AL, Kim, CJ, “A Diffuse-Interface Model for Electrowetting Drops in a Hele-Shaw Cell.” J. Fluid Mech., 590 411–435 (2007)
Bonhye, K, Chang-Jin, K, “Evaluation of Repeated Electrowetting on Three Different Fluoropolymer Top Coatings.” J. Micromech. Microeng., 23 067002 (2013)
Arcella, V, Ghielmi, A, Tommasi, G, “High Performance Perfluoropolymer Films and Membranes.” Ann. N. Y. Acad. Sci., 984 226–244 (2006)
Cytop Catalog. Available: http://www.bellexinternational.com/products/cytop/pdf/cytop-catalog.pdf
Simal, S, Benedito, J, Sánchez, ES, Rosselló, C, “Use of Ultrasound to Increase Mass Transport Rates during Osmotic Dehydration.” J. Food Eng., 36 323–336 (1998)
Bellex, “Cytop Catalog,” ed, 2009.
Cytonix. FluoroPel Coatings Selection Guide. Available: https://www.cytonix.com/Articles.asp?ID=252
Cytonix. FluorAcryl 3298 Datasheet. Available: https://www.cytonix.com/Articles.asp?ID=277
Cytonix. FluoroSyl 3750 Datasheet. Available: https://www.cytonix.com/FluoroSyl-3750-p/fsm3750_60ml.htm
Trujillo-Pino, A, Krissian, K, Alemán-Flores, M, Santana-Cedrés, D, “Accurate Subpixel Edge Location Based on Partial Area Effect.” Image Vis. Comput., 31 72–90 (2013)
Trujillo-Pino, A, “Accurate Subpixel Edge Location,” ed, 2017, p. Detection of subpixel edges with very high precision in grey level images.
Gal, O, “fit_ellipse,” ed, 2003, p. Find the best fit for an ellipse using a given set of points (a closed contour).
Andersen, NK, “Drop Shape Analysis,” ed, 2016, p. Fit contact angle by double ellipses or polynomials.
Krasovitski, B, Marmur, A, “Drops Down the Hill: Theoretical Study of Limiting Contact Angles and the Hysteresis Range on a Tilted Plate.” Langmuir, 21 3881–3885 (2005)
Pierce, E, Carmona, FJ, Amirfazli, A, “Understanding of Sliding and Contact Angle Results in Tilted Plate Experiments.” Colloids Surf. A, 323 73–82 (2008)
Ebert, D, Bhushan, B, “Durable Lotus-Effect Surfaces with Hierarchical Structure Using Micro- and Nanosized Hydrophobic Silica Particles.” J. Colloid Interface Sci., 368 584–591 (2012)
Feng, L, Li, S, Li, Y, Li, H, Zhang, L, Zhai, J, et al., “Super-Hydrophobic Surfaces: From Natural to Artificial.” Adv. Mater., 14 1857–1860 (2002)
Hang, T, Hu, A, Ling, H, Li, M, Mao, D, “Super-Hydrophobic Nickel Films with Micro-Nano Hierarchical Structure Prepared by Electrodeposition.” Appl. Surf. Sci., 256 2400–2404 (2010)
Acknowledgments
This work was supported by the National Science Foundation under Grant No. 1361919.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Trapuzzano, M., Crane, N.B., Guldiken, R. et al. Wetting metamorphosis of hydrophobic fluoropolymer coatings submerged in water and ultrasonically vibrated. J Coat Technol Res 17, 633–642 (2020). https://doi.org/10.1007/s11998-019-00250-1
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11998-019-00250-1