Abstract
In the present work, microstructure and mechanical properties like hardness, tensile, and wear of AZ91 Mg alloy have been studied for four different samples of the same composition. The first sample was as-cast alloy; the second sample was given only mechanical vibration (15 Hz-2 mm), the third sample by adding 2 wt.% ZnO as a grain refiner, and the fourth sample with a collective effect of grain refiner and the imposition of mechanical vibration during solidification. The optimum results were obtained for the fourth sample, because both mechanical vibrations and grain refiner provide nucleating sites in the melt, resulting in grain growth restriction. Microstructural studies reveal that the combined effect results in fragmentation and uniform distribution of primary α-Mg and β-Mg17Al12 phases. It is witnessed that, among all samples, the fourth sample is showing superior density and mechanical properties when compared with the as-cast sample. Hardness at three different locations (top, middle, and bottom) is increased from 53-72, 55-79, to 58-92 BHN, respectively. Similarly, yield strength, UTS, and % elongation has increased from 90-121 MPa, 140-182 MPa, to 1.8-2.8, respectively. Likewise, the coefficient of friction and specific wear rate at 5 N was decreased from 0.59-0.13 to 1.07-0.43 mm3/Nm, respectively, whereas at 10 N load, these were 0.68-0.23 and 1.69-0.47 mm3/Nm respectively.
Similar content being viewed by others
References
S. García-Rodrígueza, B. Torresa et al., Dry sliding wear behavior of globular AZ91 magnesium alloy and AZ91/ SiCp composites, Wear, 2017, 390–391, p 1–10
A.W. El-Morsy, Dry sliding wear behavior of hot deformed magnesium AZ61 alloy as influenced by the sliding conditions, Mater. Sci. Eng. A, 2008, 473, p 330–335
R.M. Pillai, K.S. Biju, and B.C. Pai, A simple inexpensive technique for enhancing density and mechanical properties of Al-Si alloys, J. Mater. Process. Technol., 2004, 146, p 338–348
W. Jiang, Z. Fan, Y. Dai, and C. Li, Effects of rare earth elements addition on microstructures, tensile properties and fractography of A357 alloy, Mater. Sci. Eng. A, 2014, 597(3), p 237–244
W. Jiang, Z. Fan, X. Chen, B. Wang, and H. Wu, Combined effects of mechanical vibration and wall thickness on microstructure and mechanical properties of A356 aluminum alloy produced by expendable pattern shell casting, Mater. Sci. Eng. A, 2014, 619(12), p 228–237
H.M. Fu, D. Qiu, M.X. Zhang, H. Wang, P.M. Kelly, and J.A. Taylor, The development of a new grain refiner for magnesium alloys using the edge-to-edge model, J. Alloys. Compd., 2008, 456, p 390–394
K. Lee, A study on grain refinement of AZ91E magnesium alloy with Al-5TiB2, Al-Al4C3 and ZnO additions, Master of Applied Science Thesis, Ryerson University (2011).
S. Saha and C. Ravindran, Effects of zinc oxide addition on the microstructure and mechanical properties of AZ91E Mg alloy, Int. J. Metal Cast., 2015, 9, p 39–48
Y. Wang, X. Zeng, and W. Ding, Effect of Al-4Ti-5B master alloy on the grain refinement of AZ31 magnesium alloy, Scr. Mater., 2006, 54, p 269–273
Q. Jin, J.P. Eom, S.G. Lim, W.W. Park, and B.S. You, Grain refining mechanism of a carbon addition method in a Mg-Al magnesium alloy, Scr. Mater., 2005, 52, p 421–423
Y. Wang, H.Y. Wang, Y.F. Yang, and Q.C. Jiang, Solidification behavior of cast TiB2 particulate reinforced Mg composites, Mater. Sci. Eng. A, 2008, 478, p 9–15
A. Maltais, M. Fiset, and D. Dubé, Grain refinement of magnesium alloy AZ91D cast in permanent mold using mechanical vibrations, Mater. Sci. Forum, 2003, 426–432, p 527–532
A. Fatai Olufemi and I. Simeon Ademola, Effects of melt vibration during solidification on the mechanical property of Mg-Al-Zn alloy, Int. J. Metall. Mater. Eng., 2012, 1, p 40–43
H.M. Guo, A.S. Zhang, X.J. Yang, M.M. Yan, and Y. Ding, Microstructure formation and mechanical properties of AZ31 magnesium alloy solidified with a novel mechanical vibration technique, Metall. Mater. Trans. A, 2014, 45, p 438–446
N. Omura, Y. Murakami, M. Li, T. Tamura, K. Miwa, H. Furukawa, M. Harada, and M. Yokoi, Effects of mechanical vibration on macrostructure and mechanical properties of AC4C aluminum alloy castings, Mater. Trans., 2009, 50, p 2578–2583
K. Kocatepe and C.F. Burdett, Effect of low frequency vibration on macro and micro structures of LM6 alloys, J. Mater. Sci., 2000, 35, p p3327–p3335
S. Hu, L. Chen, Q. Zhou, J. Huang, L. Zhang, Effect of mechanical vibration on solidified structure and mechanical properties of AZ91-0.4Ca alloy. Foundry Technol. (2018).
J. Chen, X. Chen, and Z. Luo, Effect of mechanical vibration on microstructure and properties of cast AZ91D alloy, Results Phys., 2018, 11, p 1022–1027
V. Chaturvedi, U. Pandel, and A. Sharma, Effect of mechanical vibrations on grain refinement of AZ91 Mg alloy, Mater. Res. Exp., 2017, 4(4), p 1–11
J.Y. Li, J.X. Xie, J.B. Jin, and Z.X. Wang, Microstructural evolution of AZ91 magnesium alloy during extrusion and heat treatment, Trans. Nonferrous Metals Soc. China, 2012, 22, p 1028–1034
A. Kumar, R. Kumar, S. Ansari, and S.S. Mishra, Effect of mould vibration on microstructure and mechanical properties of casting during solidification, Int. J. Eng. Res. Technol., 2014, 3, p 90–92
M.X. Zhang, P.M. Kelly, M. Qian, and J.A. Taylor, Crystallography of grain refinement in Mg-Al based alloys, Acta Mater., 2005, 53, p 3261–3270
Y.J. Chen, W.N. Hsu, and J.R. Shih, The effect of ultrasonic treatment on microstructural and mechanical properties of cast magnesium alloys, Mater. Trans., 2009, 50, p 401–408
F. Taghavi, H. Saghafian, and Y.H.K. Kharrazi, Study on the ability of mechanical vibration for the production of thixotropic microstructure in A356 aluminum alloy, Mater. Des., 2009, 30, p 115–121
H.M. Guo, A.S. Zhang, X. Yang, and M.M. Yan, Grain refinement of Al-5%Cu aluminum alloy under mechanical vibration using meltable vibrating probe, Trans. Nonferrous Metals Soc. China, 2014, 24, p 2489–2496
Y.G. Zhao, Y.H. Liang, Q.D. Qin, W. Zhou, and Q.C. Jiang, Effect of mechanical vibration on the microstructure, impact toughness and thermal fatigue behavior of cast hot working die steel, Trans. Iron Steel Inst. Jpn., 2004, 44, p 1167–1172
J.W. Zhao, S.S. Wu, L.Z. Xie, A.N. Ping, and Y.W. Mao, Effects of vibration and grain refiner on microstructure of semisolid slurry of hypeoeutectic Al-Si alloy, Trans. Nonferrous Metals Soc. China, 2008, 18, p p842–p846
D. William, Callister, Materials Science and Engineering, 2010th ed., Wiley India Pvt. Ltd., India, 2010, p 361
J. Zhu, W. Jiang, G. Li, F. Guan, Y. Yu, and Z. Fan, Microstructure and mechanical properties of SiCnp/Al6082 aluminum matrix composites prepared by squeeze casting combined with stir casting, J. Mater. Process. Technol., 2020, 283(116699), p 1–11
E. Ilanaganar, S. Anbuselvan, Wear mechanisms of AZ31B magnesium alloy during dry sliding condition, Mater. Today Proc. (2016), p. 1–9.
P.C. Meena, A. Sharma, and S. Singh, Effect of grain refinement on microstructure and wear behavior of cast Al-7Si alloys, La Metallurgia Italiana, 2015, 1, p 25–34
G.V. Bhaskar, B. Sharmila, and P.N. Chetty, Wear resistance behavior study of AZ31B Mg alloy, Int. J. Eng. Res. Technol., 2014, 3, p 2778–2782
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Chaturvedi, V., Talapaneni, T. Effect of Mechanical Vibration and Grain Refiner on Microstructure and Mechanical Properties of AZ91Mg Alloy during Solidification. J. of Materi Eng and Perform 30, 3187–3202 (2021). https://doi.org/10.1007/s11665-021-05471-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-021-05471-3